Maytag Valve

This dishwasher overfill control float mounts in the tub floor and rises with the water level to trip the float switch and stop filling. Replacing a warped or stuck float restores proper fill control and helps prevent leaks. What it does:

• Monitors tub water level and actuates the float switch to shut off the inlet valve
• Helps prevent overfilling and water leaking from the door
• Common symptoms of a faulty float include no fill, continuous filling/overfilling, or inconsistent water level

• Float and retainer

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift out the old float
• Access beneath the tub may be required to release/install the retainer
• Ensure the float stem engages the switch lever and moves freely; test-fill and check for leaks

This valve controls the flow of water into the appliance. When energized, it opens to let the correct amount of water in; when de-energized, it closes to stop flow—restoring proper fill and dependable operation. What it does:

• Opens and closes to regulate incoming water during operation
• Helps maintain correct fill levels for cycles
• Common symptoms of a failing valve: no fill or slow fill, error codes related to water supply, dripping/leaks from the valve area, or humming/clicking with little to no water flow

• 1 valve assembly

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Label and transfer hoses/wires one at a time; reuse existing hardware/fittings
• Restore water and power, then check all connections for leaks and run a test cycle

This gas surface burner valve regulates fuel flow to a cooktop or range burner for safe ignition and smooth flame control. Replace a worn or sticking valve to restore consistent flame adjustment and reliable knob operation.

• Regulates gas to the surface burner; opens/closes as the control knob is turned
• Helps resolve no-flame or no-ignition conditions when sparking is present
• Restores proper flame adjustment from low simmer to full boil
• Addresses stiff, seized, or inconsistent valve action at the knob

• Disconnect electrical power and shut off the gas supply before servicing
• Remove the knob and access the manifold to detach the old valve; note tubing and orientation
• Transfer any mounting clip or fittings from the original valve if required by your model
• After reassembly, check all connections with an approved leak-detection solution and verify burner operation

If machine has 2 coil valve, order part #WP22003834.

This is the hot water inlet valve for compatible laundry appliances. It controls the flow of hot water into the machine during fill cycles, helping ensure proper washing performance and accurate temperature mixing.

• Opens and closes to allow hot water into the tub when energized
• A failed valve can cause no hot fill, slow filling, incorrect water temperature, or leaks from the valve body
• Also lead to error codes related to water fill or extended fill times

• Disconnect power and turn off both water supplies before servicing
• Have a towel/contained pan ready for residual water in hoses
• Note hose orientation and electrical connector position before removal
• Inspect and replace inlet screen washers or hoses if restricted or worn

This 3-way water inlet valve regulates and routes incoming water into the appliance. Replacing a sticking or leaking valve restores proper fill and correct water delivery to the intended circuits, helping prevent leaks and fill issues.

• Opens and closes three solenoid-controlled ports to regulate water flow when the control calls for it
• Directs water to the correct internal path as designed
• Helps maintain proper fill levels and timing
• Common symptoms of a failed valve include no fill, slow fill, water leaking from the valve, or water entering the unit when it's off

• Disconnect power and turn off the water supply before servicing
• Keep towels/bucket handy; relieve line pressure and label hoses and wire connectors for correct reassembly
• Inspect/clean inlet screens and flush supply lines before reconnecting
• After installation, restore water and power, then run a test cycle and check all connections for leaks

"Y" Tube is being replaced. The old valve has a double water outlet, must change to this single outlet and eliminate the "Y" Tube.

Electronic water inlet valve that controls the appliance's water flow during fill cycles, restoring proper filling and helping prevent overfills, persistent fill errors, or water leaks when the original valve fails. What it does:

• Opens and closes to route water into the appliance when signaled by the control board.
• Responds to electronic fill commands; a failed valve can cause no-fill, continuous fill, or error-code symptoms.
• Can allow water leaks if seals or valve body fail.
• Works as the unit that meters fill volume for cycles that require water.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect inlet hoses and seals when installing; replace damaged hoses or gaskets to prevent leaks.
• Test the appliance through a short fill cycle after installation and check for leaks.

This cold water inlet valve is the solenoid-operated valve that opens to let cold water into your washer during fill and closes to stop flow. Replacing it restores proper fill speed and helps prevent off-cycle drips.

• Regulates cold-side water flow into the washer during fill and rinse cycles
• Opens when energized by the control; closes to stop water between cycles
• Common signs of failure: no cold fill, slow fill, or dripping into the tub
• May trigger fill/temperature errors or cause a loud hum with little/no water flow

• Disconnect power and shut off the household water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure
• Label and transfer hoses and wire connectors one-for-one to the new valve
• Inspect/clean inlet screens and flush lines; check for leaks after a test fill

16K. Mueller.

This replacement water inlet valve controls the flow of water to the appliance's dispenser and ice-making components, restoring normal fill and preventing supply interruptions when a valve fails. What it does

• Opens and closes to allow water into the dispenser and ice maker on demand
• Restores water flow if the dispenser or ice maker won't fill
• Stops water supply when closed to help prevent overfilling or continuous flow
• Common replacement for intermittent flow, no-water, or leaking symptoms

• Turn off power and shut off the water supply before starting any work
• Inspect fittings, hoses, and seals and replace any damaged components to prevent leaks
• Use basic hand tools; hand-tighten fittings and check for leaks after reconnecting water

Replacement burner valve that controls gas flow to a surface cooktop burner, restoring reliable flame control for safer, consistent cooking. Use this valve when a burner has low or no flame, uneven flame, or won't respond to knob adjustments. What it does:

• Regulates gas flow to a single surface burner so you can adjust flame size and cooking heat.
• Replaces valves that cause burners to fail to light, produce weak or sputtering flames, or not change flame level.
• Restores normal burner operation when the original valve is worn, leaking, or damaged.
• Compatible with gas cooktops and ranges.

• Turn off the gas supply and unplug the appliance before starting any repairs.
• Use appropriate hand tools; avoid overtightening fittings or damaging gas lines.
• After installation, check all connections for leaks (soap-and-water test) and verify proper burner ignition and flame.

This burner valve controls the flow of gas to a single surface burner, restoring proper burner ignition and heat control. It's a direct-replacement gas valve that helps fix intermittent or no-flame burner operation. What it does:

• Regulates gas flow to one surface burner so the burner lights and the flame responds to the control knob.
• Replaces a valve that is stuck, leaking, or not allowing gas through, which can cause a burner to fail to light or produce a weak/unsteady flame.
• Works with pilot/ignition systems to ensure consistent ignition when the knob is turned.
• Helps eliminate clicking or continuous sparking caused by failed gas delivery (when ignition sequence is otherwise OK).

• One burner valve

• Turn off the gas supply and unplug the appliance before starting any work.
• Verify valve orientation and connections match your appliance.
• Use approved fittings and check all gas connections for leaks with a soap solution or gas leak tester after installation.
• Do not attempt repairs if you smell gas; ventilate the area, avoid open flames.

This valve kit repairs the appliance's water/control valve assembly and provides the small mounting screw needed for secure installation. It replaces a worn or damaged valve kit so the appliance can restore proper valve function. What it does:

• Replaces the valve assembly components that control water flow or internal fluid routing
• Helps stop issues caused by a damaged valve kit, such as inconsistent water delivery or valve leakage
• Restores secure mounting with the included screw to prevent loose fittings
• Works as the direct replacement kit specified for the original valve location

• Disconnect power and shut off water supply before starting any repair
• Handle valve components carefully to avoid damaging seals and fittings
• Use basic hand tools; avoid overtightening the mounting screw to prevent stripping

A replacement surface burner valve that controls gas flow to a cooktop burner for consistent flame and heat. Restores proper burner response so burners light and adjust as expected. What it does

• Regulates gas flow to a single surface burner so flame size responds to the control knob
• Helps resolve a burner that won't light or produces little or uneven flame
• Replaces a worn or faulty valve that causes inconsistent temperature during cooking
• Use with the corresponding manifold and control knob assembly for full operation

• One burner valve (surface)

• Turn off gas supply and disconnect power before servicing; follow all safety procedures
• Inspect connections and fittings for proper sealing; check for leaks after installation with a soap solution
• Handle components carefully to avoid damage to valve ports and threads

The Valve-Gas is an OEM part for Whirlpool gas stoves. It controls the flow of gas from the supply line into the burner tubing, igniters, and flames themselves during the operation of the range top. Precise control of gas flow is critical for safe and efficient cooking performance.

Symptoms of a bad gas valve can include:

• Inability to ignite one or more burners  
• Unstable, intermittent burner flames
• Burners that cannot be turned low enough or click off suddenly 
• Escaping gas odor near the range

Causes of a bad valve may involve wear and tear of internal parts like diaphragms or seals letting in air/gas, corrosion on valve surfaces from gas or moisture, or damage from appliance service/movement over time. 

This Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, Amana, Magic Chef, and select Kenmore models.