Maytag Washer Parts

Repairing the problem was the easy part. Diagnosing the problem took a little more time. To diagnose the problem, it took longer because I first cleaned the Drain Pump trap from all the material it collected. Socks, hair pins, and other materials that were not cleaned from pants pockets. It then still did not drain. Repeated the process after finding more materials and a toy that punctured the hose between the tub and the drain pump. Running the drain and spin cycle takes about 11... Read more

Its under warranty so I called Sears repair. The Technician determined the pump was bad order. After a month of waiting for Sears to order the part and the back and forth on the phone, I looked for the part myself. You guys sent the part and in 2 Days my washer is working again. No word yet, from Sears part order.. Read more

Removed valve and replaced with new one. Read more

Replaced Snubber Ring installed spring kit. Watched installation video, found it very helpful to plan repair. The washer runs like new now. Read more

• Will not fill with water

After watching the YouTube video provided by Appliancepartspros and checking various forums I determined the dispenser motor had gone out. Turns out, it was a two part problem. The connectors to the motor, and the motor had corroded. Cleaned them both with vinegar. The old motor did a load before I started having problems with the CCU. I didn't learn about the CCU needing a reset under the quick diagnostics until after replacing the motor and the new part doing the same thing. Both the new... Read more

Remove the top panel by removing 3 hex nuts on the back of the washer. Inlet valve was located right underneath the panel towards the back. Remove one screw using a t20 bit and unplug the 2 plugs located on the valve. With a pair of pliers removed a tension clamp and the valve comes right off. Read more

• Door won't close

I chatted with a rep on Appliance Parts Pros and found out which parts I needed for my model of dryer. Ordered the 2 clips that held the door closed. They arrived the next day!! My dryer was very different than the video but we were able to figure out which screws to remove. The old clips popped out and the new ones popped in. Took about 30 minutes because of there being a top and bottom clip to remove and replace and line up the door parts to screw the screws back in. It works great!! I... Read more

Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine). If you replace the springs, be sure to check for the spring bracket mount. You will also need those. The washer is running fine. Next I'll work on the dryer. Read more

My wife and I along with Mat on the video replaced the upper and lower friction pads, along with the balance springs. The machine runs smooth as it did new. Thank you everyone at Appliance Parts Pro and Mat. You are a great company. P.S. my wife and I should had made our own video for you since we are both in our 60s I bet it would have been funny Thanks Again. JIm & Debbie from Texas. Read more

I watched a few on line videos. Found 2 easy things to check. The motor coupler then the clutch. It took me about 30 minutes to get everything apart and find out which problem it was. Went on line to Appliance Pros.com and ordered the new clutch.It came in 2 days. Took less than 30 minutes to get it on and get everything back together. It was awesome. Read more

I noticed when we would run washer water would stay in tub. Pump would hum but not pump water out. Layed washer on its belly . Pump was at bottom of washer. Easy access . Removed 3 screws,2 wires , & 2 hose clamps. Didn't have to call Maytag Repair man. Easy Read more

• Will not drain

I looked up the error code on the internet and determined that the drain pump had failed. I watched the Appliance Parts Pros repair video on how to replace this part, ordered a new pump and installed it myself in less than 30 minutes. This was an easy job that saved me the price of a service call, at least one hour of labor, and perhaps a markup on the part--probably around $200.00 total. I do this kind of work around the house a lot and win points with my wife. I still haven't received my... Read more

Ordered replacement knob Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Replaced the water valve. Easy repair. The repair video was spot-on. Tools needed: Slip joint pliers for removing and attaching the hoses and moving the hose clip. 5/16 nut driver. Phone to take a picture so I could get the wires put back right. Shut off the water and unplug from power. Remove the hoses. Using a 5/16 nut driver remove the single screw that holds the bracket, lift bracket slightly and pull from the washer. There is a little slack in wires and fill hose to work with. Take a... Read more

Removed washer lid, then upper front panel with controls. Popped off the front retaining ring, then pushed the boot into the washer area after detaching the detergent hose and LED light from the boot. Detached the door lock mechanism. Removed the front panel with the door. Then removed main retaining ring after loosening with Phillips head screwdriver. Removed the old boot. I found a bunch of nasty stuff in the cavity between the main drum and rotating drum which was blocking the boot from... Read more

Saw the drip, ordered the part. Unplugged machine from wall. Torx bit on my DeWalt cordless drill to remove the screws securing the lid to the machine, lifted off top cover. Turned off water supply and removed the water supply hoses from back of the machine, used needle-nosed pliers to remove spring clamps from the defective part, removed mounting screw for defective part at rear of machine. Worked the defective part out of mounting, unplugged the three electrical connectors. Then, plugged in... Read more