Gas Conv Kit Parts

Igniter and orifice assembly includes: Igniter, orifice assembly and gas tube.

The Jet Holder with Nut is an OEM part for Bosch ranges and cooktops. It holds precisely machined jets that control gas flow from each burner valve.

Causes may be wear and deterioration from prolonged heating exposure. Physical impacts or damage accumulation over time could also compromise the jet holder.

Symptoms of a bad jet holder can include:

• Inability to adjust or maintain proper flame stability and heat output
• Irregular or uneven flame patterns between surface burners
• Potential gas leaks observed at jet connections

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This LP conversion kit converts a gas dryer from natural gas to liquefied petroleum (LP/propane), supplying the fuel-specific components needed so the dryer can operate safely and correctly after a fuel-type change. What it does:

• Provides LP-compatible replacement components for the dryer's gas system to match propane fuel requirements.
• Enables correct burner operation after converting fuel, helping prevent weak or no heat and unstable flames following a fuel change.
• Used when relocating or switching a home's fuel source or when OEM conversion is required.
• Helps ensure the appliance meets manufacturer requirements for safe LP operation when installed per instructions.

• Shut off gas supply and power before beginning work; perform a gas-leak test and verify proper burner operation after installation.
• Follow the manufacturer's model-specific conversion instructions included with the kit—do not improvise parts or procedures.

Right front

This LP conversion kit supplies the manufacturer-specified components to configure a compatible gas appliance for propane use. It helps restore proper flame characteristics and safe, efficient performance after switching from natural gas service. What it does:

• Provides the correct orifice sizing and regulator setup for LP operation
• Helps address yellow/sooty flames, weak heat, or delayed ignition after a fuel-type change
• Supports stable burner ignition and proper combustion
• Intended only for models the manufacturer designates as convertible

• One LP conversion kit

• Turn off gas and electrical power; allow the appliance to cool before starting
• Follow the model-specific instructions included with the kit to change orifices and set the regulator/cap
• After installation, leak-test all gas connections and verify flame appearance per the service/installation sheet

Includes 7 spuds.

This LP gas conversion label identifies that the appliance has been converted for use with liquid propane. Applying it near the gas valve/regulator clearly communicates fuel type for safe service, troubleshooting, and future installation decisions.

• Marks a converted unit as LP fuel to prevent misdiagnosis or incorrect hookups
• Provides quick visual identification for technicians and inspectors
• Replaces a missing, damaged, or illegible conversion label
• Use when a conversion has been completed and the original label is not present

• Apply only after completing the correct LP conversion procedure for your specific model
• Clean and dry the mounting surface; place the label where specified (typically near the gas valve/regulator or rating plate)
• Do not cover existing safety or rating labels; press firmly to ensure full adhesion
• Leak-check all fittings before returning the appliance to service

This orifice spud meters gas to the burner for a consistent, correctly sized flame. Replace a clogged or damaged spud to restore proper burner output and reliable ignition on your gas cooktop or range.

• Controls and meters gas flow through a calibrated opening to the burner
• Helps ensure proper flame size and color when matched to the correct burner and fuel type
• Common symptoms of a failing or clogged spud: weak or uneven flame, yellow tipping, or delayed ignition
• Damaged threads or a stripped orifice can prevent correct sealing and fuel delivery

• Shut off gas supply and disconnect power; allow the appliance to cool
• Access the orifice holder/manifold for the affected burner; remove the old spud with an appropriate orifice wrench or nut driver
• Start the new spud by hand to avoid cross-threading; tighten snugly—do not overtighten brass threads
• Restore gas and check for leaks with an approved leak-detection solution; verify flame quality and adjust per the service manual

Natural gas orifice spud.

This burner venturi is the air-gas mixing tube between the orifice and burner head on select gas cooktops and ranges. The 10.7 mm size matches specific burners. Replacing a clogged or damaged venturi restores proper flame and dependable ignition.

• Mixes incoming gas with primary air and channels it to the burner head
• Can help resolve weak/uneven flame, yellow tipping, or delayed ignition when the original venturi is restricted or damaged
• Supports consistent heat output and stable blue flames on the matched burner
• Installs between the orifice holder/nozzle and the burner base

• Shut off gas supply and power; allow the appliance to cool completely
• Remove burner cap and head; note the venturi's orientation before removal
• Clear debris from the orifice area without pushing material into the jet
• Reassemble, restore gas, then leak-test and verify proper flame pattern

This LP conversion kit adapts your compatible gas appliance from natural gas to liquid propane. It provides model-specific components to size the fuel delivery for LP, helping ensure proper flame characteristics and consistent heating performance. What it does:

• Converts the appliance for use with LP (propane) fuel
• Configures orifice sizing and regulator settings for LP on compatible models
• Helps correct oversized yellow flames, weak heat, or sooting when operating on propane without proper conversion
• Commonly needed when relocating to a home with propane service

• One LP conversion kit

• Disconnect electrical power and shut off the gas supply; allow the appliance to cool before starting.
• Follow the model-specific conversion procedure to change orifice spuds and convert the pressure regulator; perform a leak check and verify flame appearance.
• After conversion, test all burners and the oven for proper operation across settings.

This LP conversion kit adapts compatible gas appliances from natural gas to liquid propane. Proper conversion helps ensure safe ignition, correct flame size, and consistent heating when your installation uses propane instead of natural gas. What it does:

• Converts the appliance's gas system from natural gas to LP/propane
• Matches burner/orifice sizing and regulator setting to propane fuel characteristics
• Helps correct symptoms tied to the wrong fuel: tall yellow flames, sooting, weak heat, uneven burner performance
• Required when connecting the appliance to an LP/propane supply

• Includes LP conversion kit

• Must be installed by a gas technician; follow local codes and the model-specific instructions
• Shut off gas and power before starting; verify all connections are leak-free with an approved leak-detection solution
• Replace the specified orifices and set/convert the pressure regulator to LP as directed; apply the provided LP identification label
• After conversion, verify flame appearance and manifold pressure

This LP orifice spud directs propane gas to a burner for correct flame size and stable cooking heat. It's the specific replacement used in LP-configured gas cooktop/oven burners to restore proper gas flow. What it does:

• Meters propane flow to a burner for consistent flame performance.
• Used in LP (propane) conversions or LP-configured burners.
• Common symptoms it can fix: burner won't light, weak or uneven flame, or poor heat control.
• Fits into the burner valve/manifold assembly and works with the burner head.

• Turn off the gas supply and disconnect power to the appliance before servicing.
• Use correct LP conversion instructions for your appliance and replace only with the specified orifice for LP.
• Hand-start threads, then snug with the appropriate wrench; avoid over-tightening.

This 13.7 mm venturi is the burner mixing tube used on select gas cooktops and ranges. It blends gas with air to create a stable flame and helps restore consistent burner performance when the original is clogged or damaged.

• Mixes gas from the orifice with air to support proper ignition and flame quality
• Helps maintain a steady blue flame and even heating
• A restricted or damaged venturi can cause weak or uneven flames, delayed ignition, yellow/orange flames, or popping/lifting
• Replacing a corroded or blocked venturi can improve burner performance

• Shut off gas supply and power; allow the surface to cool before servicing
• Remove grates, burner caps, and burner head to access the venturi; note orientation and routing
• Seat the venturi fully over the orifice; transfer/reuse any original screws, spacers, or gaskets if applicable
• Restore gas and check connections with a soapy-water test; verify flame height and quality