Range / Cooktop / Oven Control Board

This electronic oven control board governs bake/broil power, temperature regulation, and the clock/display. Replacing a failed control helps restore accurate heating and responsive controls so your oven can run cycles reliably again. What it does

• Interprets keypad inputs to start/stop bake, broil, and clean cycles
• Regulates oven temperature using the sensor feedback and cycles heating elements via internal relays
• Powers and manages the clock, timer, and digital display
• Common symptoms include no heat, won't start, erratic temperatures, blank/garbled display, beeping, or control-related error codes

• 1 electronic control board (ERC3B)

• Disconnect power at the breaker before servicing
• Transfer wiring and mounting hardware from the original control one connector at a time; avoid bending pins
• Reuse your model's existing overlay/faceplate or keypad as required; seat ribbon cables fully and squarely
• After installation, set the clock and verify operation; the tech sheet for calibration if applicable

This electronic oven control board is the brain of your range or wall oven. Replacing a failed board restores the display and keypad response and allows the appliance to heat and run bake/broil cycles reliably again.

• Controls relays for bake and broil circuits
• Uses oven sensor feedback to regulate and maintain temperature
• Powers the time/temperature display and reads keypad inputs
• Common symptoms: blank or erratic display, unresponsive buttons, F-code errors, oven won't heat or shuts off mid-cycle

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Static-sensitive component—handle by the edges and avoid touching circuitry
• Note/photograph wire locations; transfer connectors one at a time to the new board
• Mount the board in the control panel, secure connections, restore power, and test

This factory fixing kit supplies the OEM hardware required to secure the appliance or designated components during installation or service. Replacing missing or damaged fasteners restores a solid, aligned mount so the unit stays stable without shifting, rattling, or gaps.

• Provides the correct hardware to fasten parts per your model's installation or service instructions
• Replaces stripped, corroded, or missing screws/clips that lead to looseness
• Helps maintain alignment and clearances to prevent gaps, rattles, or vibration
• Typical symptoms: loose mounting, panels that shift, or movement when opening/closing doors or drawers

• Disconnect power; shut off water or gas if applicable before starting work
• Follow the model-specific installation/service manual for attachment points and sequence; use the proper driver bit and do not overtighten
• Verify the unit is level and securely anchored; check clearances and operation after securing

This electronic control board is the appliance's central controller, coordinating power to key components so cycles start, run, and finish correctly. Replacing a failed board restores reliable, automatic operation and resolves control-related faults. What it does:

• Orchestrates timing and power to major loads (motors, valves, heaters, pumps)
• Failure may present as no start, won't complete cycle, intermittent operation, or unresponsive/erratic controls
• Can prevent individual components from running even when they test good
• Susceptible to damage from power surges, overheating, or moisture intrusion

• 1 electronic control board

• Disconnect power at the breaker before servicing; verify power is off
• Use ESD protection and handle the board by the edges only
• Access the control compartment, photograph wiring, and move connectors one at a time to matching terminals
• After installation, run a diagnostic/test cycle per your tech sheet

This electronic control module generates and manages ignition spark for DSI-equipped gas ovens/ranges. Replacing a failed unit restores reliable burner lighting and can resolve issues such as no spark, repeated clicking, or the oven/broiler not igniting.

• Generates high-voltage pulses to ignite gas at the DSI electrodes
• Times and controls ignition cycles; energizes the gas valve only during commanded ignition
• Monitors flame presence through the sense circuit and may retry or lock out if ignition fails
• Common symptoms of failure: oven or broiler won't ignite/heat, no clicking/spark, intermittent ignition, or continuous clicking
• Intended for models that use direct-spark (DSI) ignition systems, not glow-bar/hot-surface igniters

• Disconnect power and shut off gas supply before servicing
• Handle the control as an electrostatic-sensitive device; avoid touching terminals
• Transfer wires one at a time and mount the module securely with a proper ground
• After reassembly, restore utilities and verify normal ignition operation

The Electronic Control Board is an OEM part for Whirlpool ranges. This control board manages and regulates the range’s functions, including temperature settings, timer operations, and control of the oven's heating elements. 

Causes of a bad electronic control board include electrical surges, overheating, and aging components.

Symptoms of a bad Electronic Control Board include:

• The range not heating properly
• Error codes displayed on the control panel
• Unresponsive or erratic buttons and controls
• Inability to set or maintain temperatures accurately

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This clock timer is the range/oven's electronic control that runs bake and broil and keeps time. Replacing a failed unit restores the display and keypad response so the oven can start and operate correctly.

• Controls oven heating by switching relays for bake and broil
• Provides clock and timer functions on the front display
• Receives keypad inputs to set temperatures, times, and cooking modes
• Typical failure symptoms: blank or dim display, unresponsive buttons, oven won't start or heat, intermittent beeping or error codes

• Disconnect power at the breaker before servicing
• Note/photograph wire locations; move connectors to the new control one at a time
• Handle the board by the edges and use anti-static precautions
• Transfer any model-specific brackets or faceplate/overlay as required and set the clock after installation

The Frigidaire Range Control is an OEM component specifically designed for Frigidaire ranges. Located on the control panel, the range control houses all interactive buttons and knobs to operate the cooktop burners and oven. 

Causes of failure include damage from excess moisture, cracks developing from repeated tightening/loosening of knobs, or wear of electronic switches impacting responses.

Symptoms of a bad range control include:

• Unresponsive or inaccurate oven/stovetop controls  
• Inability to power on or adjust temperatures
• Faulty burners failing to ignite or flame improperly
• Loose, damaged, or missing knobs hindering the use

This OEM component is also compatible with Crosley, RV, and some Kenmore-branded ranges and ensures a straightforward repair experience.

The Control Board is an OEM part for Frigidaire ranges. As the central processing unit, this electronic board works diligently behind the scenes to operate all cooktop, oven, and control features through integrated circuits and software programming. Proper board functioning is vital for commanding reliable and precise appliance performance.

Causes of failure can involve power fluctuations over the long lifespan of the range, manufacturing errors in a small percentage of units, or physical damage to sensitive board components. 

Symptoms of a faulty control board include:

• Inability to ignite oven or cooktop burners despite efforts to reset  
• Lights, timers, or touch controls becoming totally unresponsive
• Failure to advance through cooking cycles or modes 
• Strange buzzing or clicking noises localized inside the control panel area

Replace with this genuine Frigidaire replacement board to regain complete functionality and avoid further diagnostic hassle. Compatible with some Electrolux, Jenn-Air, and Kenmore ranges as well. 
 

The Main Control Board is an OEM part for Frigidaire ranges. As the central processing unit, it coordinates bake/broil elements, lights, timers and sensory systems. Located inside the control panel area, this board continuously monitors range functions and relays information to the control display.

Causes can be splash or spill damage, power fluctuations over time, or inherent component failures due to age and usage. With proper replacement, full range functionality is restored.

Symptoms of a bad control board include:

• Knobs or buttons not working on the control panel
• Elements failing to heat properly
• Erratic temperature display readings
• Inability to preheat or maintain set oven temperatures
• Control locks that prevent range operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The PCB Assy Power is an OEM part for LG gas ranges. It regulates and monitors the electrical control systems to safely operate burners, oven functions, and auxiliary components. The power board receives inputs from the control panel and thermocouples to distribute outputs that power components including ignitors, valves, and fans. 

Causes of a bad power board can include liquid damage, failures due to intense heat cycling over time, and issues arising from manufacturing defects.

Symptoms of a bad PCB Assy Power include:

• Burners not igniting or functioning properly
• Oven not heating or baking as expected 
• Faulty or unresponsive control panel 
• Error codes displayed

This genuine LG replacement ensures the range's control and safety systems perform reliably. It is also suitable for ranges by Sears/Kenmore containing LG mechanisms and electrical hardware. Installing this high-quality OEM board protects your investment and restores full functionality.

This power board assembly manages and distributes electrical power within the appliance's control and heating circuits. Replacing a failed board can restore consistent power, responsive controls, and reliable heating when the unit won't turn on or behaves erratically.

• Routes incoming power to the appliance's control and load circuits
• Works with the control system to switch relays and energize components as commanded
• Supports reliable operation of powered components during cooking cycles
• Failure signs include: unit won't power up, no heat, dead/unresponsive display, or intermittent shutdowns

• Disconnect power at the breaker or unplug before servicing
• Electronics are static-sensitive—use ESD protection and handle the board by the edges
• Photograph/label all wiring; transfer connectors to the new board one at a time
• Ensure all connectors are fully seated and mounting hardware is secure before restoring power

The Controller is an OEM replacement part for Frigidaire ovens. It acts as the brain of the oven, managing and regulating various functions such as temperature control, timer operations, and user interface.

Symptoms of a bad controller include:

• Oven not heating or maintaining proper temperature
• Display or control panel not functioning correctly
• Specific cooking modes or features not working as intended
• Error codes or warning lights indicating a controller issue

Causes of a bad controller can include electrical faults, power surges, or component failure due to age or excessive heat exposure. Faulty wiring connections or damage to the circuit board can also lead to controller malfunctions.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore oven models.

This electronic control board is the command center for your oven/range. It interprets keypad inputs, switches bake/broil circuits, and regulates temperature via the sensor to restore responsive controls, accurate timing, and consistent heating when the original board fails.

• Receives user input and drives the clock/timer and display
• Controls power to bake and broil relays or igniters based on sensor feedback
• Regulates oven temperature and cycle timing
• Stores/displays fault codes to help diagnose issues
• Typical symptoms: no heat or intermittent heat, unresponsive controls or dead display, erratic temperatures, beeping or error codes

• Disconnect power at the breaker before servicing; verify no voltage is present
• Handle the new board with ESD care; avoid touching circuitry and components
• Move connectors one at a time to matching terminals; reuse existing mounting hardware and panel components as your model requires
• After reassembly, restore power, set the clock, and run a test preheat; for diagnostics or temperature calibration if needed

This electronic oven control board (ERC3HP) runs the oven's temperature, bake/broil functions, and display. Replacing a failed board restores accurate heating, clock/timer operation, and responsive controls so your oven cooks reliably again.

• Regulates power to bake and broil elements to maintain the set temperature
• Manages oven cycles, timing, and the digital clock/display
• Reads keypad inputs and switches relays to start/stop heating functions
• Common failure symptoms: no heat or erratic temps, blank/flickering display, unresponsive controls, or recurring error codes/beeping

• Disconnect power at the breaker before servicing; verify no voltage
• Handle the PCB by the edges and use anti-static precautions
• Photograph/label connectors; transfer wire harnesses and any brackets from the original board
• After installation, set the clock and run a test bake to verify operation

The Control Board is an OEM component specifically designed for Frigidaire ranges. It plays a crucial role in regulating and monitoring the various electrical functions of the range, such as the oven bake/broil elements, ignition system, temperature display, and timer functions.

Symptoms of a bad control board include issues like:

• The oven not heating up or baking/broiling unevenly
• Electrical components like the display or controls malfunctioning
• Error codes appearing on the display
• Unresponsive or inaccurate temperature and time settings

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.