Range / Cooktop / Oven Switch
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304493153
The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.
Symptoms of a bad door switch can include:
- Oven failing to automatically go into bake or warm modes after door closure
- Interior lights not turning on when the door is opened
- Control buttons/display remaining constantly lit instead of dimming
- Oven not heating or functioning properly in different modes
Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.
This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.
Do-It-Yourself Stories from Customers like You
Frigidaire microwave oven lights and timer work but oven doesn't heat Reese F. • Essex Junction , VT • August 16, 2015
I diagnosed this problem via the web and the advice was spot on. The problem was a failure of the bottom door switch. I used a multimeter to verify that the switched never closed properly. It took me a minute to figure out how to remove the old switch (press a release tab under the switch while simultaneously rotating counter-clockwise). That was about the most difficult part of the repair.
Read more
More
$56.95
- Compare At:
-
$68.34
- You Save:
-
$11.39
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304508926
Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.
Do-It-Yourself Stories from Customers like You
The control knob was orginal equipment but the switch installed by a sears tech was not and the knob eventually would not work the switch Kevin W. • Yucca Valley , CA • December 19, 2016
I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair.
Read more
More
$64.70
- Compare At:
-
$76.35
- You Save:
-
$11.65
Genuine Frigidaire part
By: Frigidaire
Part Number: 316580614
Burner won't spark or click when you turn the knob? This igniter wiring harness restores the electrical connection between switch and igniter. 30-minute DIY fix.
Do-It-Yourself Stories from Customers like You
The back left burner didn't light and didn't click when turned the knob Oceanna C. • Watsonville , CA • April 07, 2016
My husband and myself didn't agree on which part was the exact problem. He felt it was the valve. I felt it was the ignitor/ orifice. And we both agreed the Harness-Ignitor needed to be replaced. So we ordered all 3, and I'm not sure if in fact all three were needed or not, but now with those parts replaced, the range is working like brand new!! Thanks to all the videos and diagrams on the website we were able to fix it ourselves easily. And the price was cheaper then other websites, also it...
Read more
More
$78.78
- Compare At:
-
$93.75
- You Save:
-
$14.97
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304527841
The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.
Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.
Symptoms of a bad oven light rocker switch include:
- The oven light failing to illuminate when the door is opened
- The light remaining on even when the door is closed
- An inconsistent or flickering oven light
- The switch itself becoming loose, cracked, or non-responsive
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
1 of the 4 burners would not ignite with its own control Shane W. • Fullerton , CA • November 15, 2022
Removed & replaced igniter switch assembly. The hardest part was figuring out how to remove the range top...look up a YouTube video with your manufacturer and model number to see how to do it.
Read more
More
$15.50
- Compare At:
-
$18.45
- You Save:
-
$2.95
Genuine Frigidaire part
By: Frigidaire
Part Number: 316239601KIT
Fix a burner that won't turn off or heat properly with this dual infinite switch. Controls both inner and outer element rings. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Needed a surface element dual control switch for my frigidaire range as the surface element would remain on èven when the switch was turned off Michael H. • Lauderhill , FL • July 22, 2016
Relatively easy DIY
Read more
More
$63.65
- Compare At:
-
$133.26
- You Save:
-
$69.61
Genuine Frigidaire part
By: Frigidaire
Part Number: 318191000
Burner won't heat, stuck on high, or works intermittently? This cooktop burner control switch restores reliable on/off control. Easy DIY repair.
Do-It-Yourself Stories from Customers like You
Switch was bad on cooktop Carl S. • Farmville , VA • October 28, 2016
Replaced the switch
Read more
More
$77.23
- Compare At:
-
$103.97
- You Save:
-
$26.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP74003122
Fix a burner stuck on high or won't adjust temperature with this infinite switch. Controls cooktop burner heat levels. DIY repair in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Element would stay on high even at lower settings why it would fail in the "high" mode is not a good design David M. • Suffield , CT • February 04, 2015
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element
Read more
More
$61.56
- Compare At:
-
$73.26
- You Save:
-
$11.70
Genuine Frigidaire part
By: Frigidaire
Part Number: 318394803
Has three terminals.
Do-It-Yourself Stories from Customers like You
Oven light stayed on when door was closed Robert S. • Jacksonville , IL • June 14, 2015
When trouble shooting the problem I found that the light switch housing outer lip was broken allowing the switch to push through mounting surface behind the oven door. This is a slide in range so, I proceeded to pull the range away from the counter where I could unplug the power cord. Once the power was off like located the panel on the right upper side of the unit and removed the screws to allow access to the switch. I then unplugged the switch from the wiring harness and removed the damaged...
Read more
More
$52.68
- Compare At:
-
$63.22
- You Save:
-
$10.54
Genuine Lg part
By: Lg
Part Number: EBF60662911
This switch assembly is the door lock mechanism for select front-load washers. It detects when the door is closed and locks it during operation, allowing the washer to start and run safely without interruptions.
- Monitors door position and signals the control; failure can prevent the cycle from starting or trigger door/lock errors
- Engages the latch to secure the door during wash and spin; a bad lock may stop the cycle mid-wash
- Coordinates door unlock at cycle end; faults can delay or prevent unlocking
- Intermittent operation may cause sporadic starts or pauses
What's included: One switch assembly. Install notes:
- Disconnect power and turn off water supply before servicing
- Access the lock behind the front panel at the door opening; remove the door boot clamp to reach the mounting screws
- Move wire connectors to the new assembly one at a time to maintain placement
- Reassemble and verify proper locking and unlocking before running a full cycle
This part fixes the following symptoms
-
Doesn't shut off
-
Gas igniter glows, but will not light
See more...
Do-It-Yourself Stories from Customers like You
All the igniters spontaneously began to fire Michael S. • Adams , NY • October 12, 2019
Found a YouTube video online that provided instruction on how to change out the part.
Read more
More
$74.95
- Compare At:
-
$89.19
- You Save:
-
$14.24
Genuine Ge part
By: Ge
Part Number: WB24T10147
This high-amp SPDT switch routes power between circuits in cooking appliances to control items such as locks, element relays, or fans. Replacing a worn switch restores dependable operation and helps eliminate intermittent on/off issues. What it does:
- Single-pole, double-throw action directs power between NO/NC circuits based on actuator position
- Used to signal or control a component per the model's design (e.g., latch/lock, relay, fan)
- Failure symptoms can include no activation, stuck-on/off behavior, intermittent operation, or heat-damaged terminals
- Electrical tests may show incorrect continuity between COM–NO/NC when pressed or released
What's included:
- Includes: 1 SPDT high-amp switch
Install notes:
- Disconnect power at the breaker or unplug the appliance before servicing
- Label or photograph wiring; move leads to matching COM/NO/NC terminals on the new switch
- Mount with the correct actuator orientation and secure any bracket or screws
- Inspect connectors for heat damage; ensure tight spade fits, restore power, and test operation
Do-It-Yourself Stories from Customers like You
Faulty self cleaning latch Gregory K. • Bel Air , MD • December 28, 2016
Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough.
Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the...
Read more
More
$21.95
- Compare At:
-
$26.12
- You Save:
-
$4.17
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8286070
If your triple burner stays on high or won't adjust temperature, this infinite switch restores precise heat control for small, medium, and large rings.
Do-It-Yourself Stories from Customers like You
Lower front left burner would not shut off this burner is the single dual and triple element burner Maurice B. • San Diego , CA • May 07, 2015
Replace switch
Read more
More
$109.41
- Compare At:
-
$130.20
- You Save:
-
$20.79
Genuine Frigidaire part
By: Frigidaire
Part Number: 316445501
This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.
- Directs power to the associated circuit when switched on or off
- Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
- Helps restore positive, consistent control from the backguard/control panel
What's included: One switch Install notes:
- Disconnect power at the breaker before servicing
- Access the switch from the control panel/backguard; retain screws/clips
- Label/photograph wire positions and transfer leads one at a time to the new switch
- Ensure firm terminal connections, reassemble, restore power, and test operation
Do-It-Yourself Stories from Customers like You
Oven light would not turn off Stanley W. • Beaver Creek , OH • December 23, 2016
Replaced the switch
Since I was not familiar with this type of socket it would have helped to know the oven had to be pulled out of the cabinet a few inches
Read more
More
$73.95
- Compare At:
-
$87.26
- You Save:
-
$13.31
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9763761
If your range burner won't heat, cycles incorrectly, or buzzes when turned on, a faulty infinite switch is likely the cause. Moderately easy DIY repair.
Do-It-Yourself Stories from Customers like You
Stems were broken on handles. Knobs didn't work correctly. Dan R. • Glendale , CA • May 06, 2020
Had to replace both switches. The hard part was getting the control panel off to get access. Only a few screws but even after getting them out, really struggled getting it off. After getting off, discovered that you need to get it lifted up before pulling it off.
Read more
More
$142.95
- Compare At:
-
$170.11
- You Save:
-
$27.16
Genuine Whirlpool part
By: Whirlpool
Part Number: W11162115
Burner stuck on high or won't regulate temperature? The infinite switch controls heat levels. Common DIY repair, typically 10 minutes to install.
Do-It-Yourself Stories from Customers like You
Burner stayed on high when moved to lower heat setting David L. • Melrose , MA • December 27, 2019
I watched an 8-minute video on YouTube. Identified and ordered the part from AppliancePartsPros that a $12 shipping fee was received in 2 days. Took 10 minutes or less to install. Years ago without next-day parts and YouTube, this $60 repair would have cost me $200+.
Read more
More
$78.27
- Compare At:
-
$93.14
- You Save:
-
$14.87
Genuine Ge part
By: Ge
Part Number: WB24K5083
Fix burners that won't spark or click constantly with this igniter switch. Mounts on the gas valve stem to activate spark ignition. Easy 15-minute repair.
Do-It-Yourself Stories from Customers like You
Clicking from ignitor mode would not stop after burner lit Jeffrey Maclachlan V. • Nederland , CO • September 03, 2017
Turned out the little switches on the knob shaft had corroded and were staying on. There was constant continuity showing with an ohm meter. Replacing the switches was very easy (always disconnect power to the unit before servicing). Bought a new ignitor module as a backup as they do go out of production after 10 years or so- another cheap and easy fix if needed in the future.
Read more
More
$25.61
- Compare At:
-
$30.48
- You Save:
-
$4.87
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4456901
Fix sparking or non-working igniter switches with a new switch harness. Connects control switches to cooktop wiring. Moderate DIY repair, 1-2 hours.
Do-It-Yourself Stories from Customers like You
Igniter not working. Adrian H. • Totowa , NJ • January 18, 2022
Replaced the Spark Module and the Wire Harness. Works like new.
Read more
More
$117.54
- Compare At:
-
$141.05
- You Save:
-
$23.51