Range / Cooktop / Oven Switch
Genuine Ge part
By: Ge
Part Number: WB23K34829
The Infinite Switch is an OEM part for GE electric ranges. It regulates precise temperature settings for the bake and surface elements. This is specifically for 6" inch elements.
Symptoms of a bad infinite switch include:
- Wide variations in cooking temperatures
- Failure to attain or maintain desired heat levels
- Non-working or faulty temperature selector dial
Causes can involve degraded metal contacts, worn internal components, or damaged wiring connections after extended use.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore electric range models.
Do-It-Yourself Stories from Customers like You
We couldn't control the burner temperature. Steven A. • New Carlisle , OH • December 20, 2021
The parts are under the stovetop and the knobs are attached to them. We bought the correct ones from AppliancePartsPros, these were the correct ones. Seems we have an oddball stovetop. It's a GE drop in stove. The parts were easy to change. It was a simple matter of putting the wires on the new switch in the same place there were on the switch. I took phone pics of the wire locations before I took them off and only did one switch at a time. Turn the power off at the breaker panel first of...
Read more
More
$56.95
- Compare At:
-
$67.77
- You Save:
-
$10.82
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10215034
Fixes dual burner stuck on high, won't heat, or no inner ring control. This infinite switch restores precise temperature selection. 45-60 minute DIY repair.
Do-It-Yourself Stories from Customers like You
Burner didn't turn on Bruce H. • Granger , IN • August 18, 2015
I replaced both the element and the switch. It was a relatively easy fix, although I needed a second set of hands to hold the stovetop upright while I did the replacement. The entire job took about 45-60 minutes.
Read more
More
$161.78
- Compare At:
-
$192.52
- You Save:
-
$30.74
Genuine Whirlpool part
By: Whirlpool
Part Number: 12002121
If your cooktop burner only works on high or won't adjust temperature, the infinite switch likely failed. DIY-friendly repair in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Right front double burner only worked on high!!!! Rolland F. • Brasher Falls , NY • September 21, 2014
Ordered the part and a few days later it arrived and I turned off the power and took a few screws out and unpluged the old one and pluged in the new .. Works like a charm.. Was very easy to fix....
Read more
More
$79.74
- Compare At:
-
$94.89
- You Save:
-
$15.15
Genuine Whirlpool part
By: Whirlpool
Part Number: WP74011243
Burner stuck on high or won't heat? The infinite switch controls surface element power from low to high. Common DIY fix restores heat adjustment.
Do-It-Yourself Stories from Customers like You
No control of range burner burner was either off or on high no heat adjustment Robert B. • Toms River , NJ • September 06, 2014
Replaced infinite switch
Read more
More
$73.95
- Compare At:
-
$87.26
- You Save:
-
$13.31
Genuine Frigidaire part
By: Frigidaire
Part Number: 318293818
If your cooktop burner won't heat, stays on high, or won't turn off, a faulty burner control switch is often the cause. DIY repair in 15-30 minutes.
Do-It-Yourself Stories from Customers like You
Failure of switch/controller on stove top. William S. • League City , TX • March 19, 2024
Ordered the switch from AppliancePartsPros.com and received promptly.
Read more
More
$67.95
- Compare At:
-
$80.86
- You Save:
-
$12.91
Genuine Frigidaire part
By: Frigidaire
Part Number: 808136601
This is a door-activated switch that detects whether the oven door is open or closed. It controls functions such as the oven light or signals the control board about door position. Replace this switch if the oven light stays on or off regardless of door position, or if the oven does not operate correctly due to a faulty door signal.
Do-It-Yourself Stories from Customers like You
Oven light would never turn off. Raul R. • Northlake , IL • March 15, 2018
Bought a door light switch from your company and used it to replace the bad one from my stove.
Read more
More
$52.46
- Compare At:
-
$62.95
- You Save:
-
$10.49
Genuine Whirlpool part
By: Whirlpool
Part Number: 12002790
Burners won't spark or ignite? This igniter switch assembly restores reliable ignition to gas burners. Most DIYers complete this repair in 20-30 minutes.
Do-It-Yourself Stories from Customers like You
Continuous sparking and then a fire Richard B. • San Dimas , CA • March 04, 2017
A few weeks back, when shutting off a burner, the igniter started sparking and wouldn't stop. Working the knobs and jiggling them got it to stop. Fast forward a few weeks. Finish cooking, go sit down to eat. Hear snapping noise, go look, see burners are all off and the igniters are all sparking. Jiggle the knobs. Poof! Flames come out the top one! What a stink. Unplugged stove, finished dinner. Loosened the cooktop and investigated. Ordered switch. Two days later, part arrives. Two screws...
Read more
More
$102.32
- Compare At:
-
$122.78
- You Save:
-
$20.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9757262
Oven light not turning on when door opens? This door-activated switch detects door position and controls interior lighting. Easy push-in installation.
More
$76.79
- Compare At:
-
$91.38
- You Save:
-
$14.59
Genuine Whirlpool part
By: Whirlpool
Part Number: 12002791
Burner won't spark or click when turned to Lite? This igniter switch mounts on the gas valve to signal the spark module. DIY fix in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Cleaning stove top fried ignitors opn maytag gas double oven/stove Rainer F. • Gloversville , NY • August 15, 2016
Ordered ignitor harness and two burners (Holder/Orifice) and with supplied videos spent about 40 minutes exchanging parts - saved roughly $500.
Must say, great parts (look original), good price, easy web site and, most of all, helpful video!
Read more
More
$102.32
- Compare At:
-
$122.78
- You Save:
-
$20.46
Genuine Frigidaire part
By: Frigidaire
Part Number: A00056506
This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:
- Provides the electrical on/off or function control for the appliance circuit.
- Replaces a failed switch that can cause intermittent operation or unresponsive controls.
- Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
- Connects to the existing wiring harness and mates with the original mounting points.
What's included: One switch assembly. Install notes:
- Disconnect power to the appliance before beginning any work.
- Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
- Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
- Restore power and verify the replaced switch operates the function correctly.
More
$28.95
- Compare At:
-
$34.16
- You Save:
-
$5.21
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3148955
Fix a burner that won't turn off, stays on high, or won't heat. This infinite switch restores precise temperature control for electric cooktop elements.
Do-It-Yourself Stories from Customers like You
Electric burner control switch William F. • Teutopolis , IL • March 08, 2017
Turn the power off to the range. Pull off the black control knob. Remove 6 - 5/16 screws in back of the range behind the controls panel. Take out 2 screws (behind the control knob) in front that hold the control swirch in the panel. Remove each wire from the old switch and place it onto the new switch (one at a time)so get the wires are installed in the correct place. Make sure the wire are tight on the new switch. Install the new switch, put the two mounting screws in, reinstall the back, put...
Read more
More
$87.60
- Compare At:
-
$104.24
- You Save:
-
$16.64
Genuine Whirlpool part
By: Whirlpool
Part Number: WP74007806
Fix burners that won't light with this cooktop igniter switch wire assembly. Restores reliable spark ignition when switches fail. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Three out of 5 igniter switches wouldn't work Marcus B. • Eads , TN • February 11, 2017
Replaced igniter switch harness
Read more
More
$102.35
- Compare At:
-
$122.82
- You Save:
-
$20.47
Genuine Bosch part
By: Bosch
Part Number: 00622858
If your oven won't start or runs with the door open, this door interlock switch detects proper closure and latching. DIY repair in under an hour.
Do-It-Yourself Stories from Customers like You
Broil element had gone bad due to age and use Sherwood O. • Orange , CA • August 22, 2015
This turned out to be a very complicated repair ONLY because the wires that attached to the very far end of the broil element came detached inside and behind the wall of the oven. It is one step this side of impossible to fish the wires out and reconnect them to the new element.
This would be a very easy job PROVIDED that you do not allow the two wires that connect to the element to become detached inside the rear oven wall.
Read more
More
$31.43
- Compare At:
-
$37.40
- You Save:
-
$5.97
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304494425
This wiring harness connects the appliance's electrical components to restore reliable power and signal routing. It replaces a damaged or worn harness to help resolve power loss and intermittent electrical issues. What it does:
- Transfers power and control signals between components so controls and motors can operate
- Replaces frayed, burned, or broken wiring that can cause intermittent operation
- Helps stop failures that lead to no-start or loss of specific functions
- Restores secure connector fit to reduce arcing or poor connections
What's included: One wiring harness as shown Install notes:
- Always disconnect power before servicing the appliance
- Match connectors and wire routing to the original harness; avoid stretching or pinching wires
- Secure fasteners and strain reliefs; verify all connections are fully seated
- If you find heat or burn damage at terminals, inspect adjacent components for root cause
More
$66.78
- Compare At:
-
$79.47
- You Save:
-
$12.69
Genuine Ge part
By: Ge
Part Number: WB18T10389
Replacement switch harness that connects a cooktop or range surface element switch to the appliance wiring, restoring secure electrical connections so burners heat reliably and reduce intermittent or unsafe operation. What it does:
- Carries power between the surface element (infinite) switch and the cooktop element or terminal block.
- Restores reliable heating when a damaged harness causes intermittent or no heat.
- Replaces frayed, burned, or corroded wiring that can cause arcing, sparking, or a burning smell.
- Keeps connector terminals secure to prevent loose connections and erratic element behavior.
What's included: One switch harness. Install notes:
- Disconnect all power (unplug range or shut off circuit breaker) before starting any work.
- Make secure, fully seated connections; avoid pinched or kinked wires and route harness clear of heat sources.
Do-It-Yourself Stories from Customers like You
Surface top burner on gas stove would not ignite Richard S. • Cottage Grove , MN • June 02, 2015
Replaced igniter wire harness.
Read more
More
$74.95
- Compare At:
-
$88.44
- You Save:
-
$13.49
Genuine Ge part
By: Ge
Part Number: WB24K5085
Fixes F1 or F2 error codes and prevents overheating in ovens. This safety switch monitors temperature limits to protect components. Direct fit part.
Do-It-Yourself Stories from Customers like You
It would show a message of f2 after the oven had been on for about 15 20 minutes Elaine M K. • Pottstown , PA • November 09, 2015
We purchased a part called Limit Switch from you. It totally corrected the problem.
Read more
More
$55.26
- Compare At:
-
$65.21
- You Save:
-
$9.95