Refrigerator Dispenser Parts

Ordered the entire control panel. Took only 30 minutes to replace. Once I received the new part, it was obvious how easy it would be to replace. A thin putty knife and a little care not to damage the surrounding surface was all that was needed. Read more

Replaced both with the parts ordered from Appliance Parts Pros. Read more

I replaced the part by popping off the plastic frame and removing several easily-accessable screws. Three small electrical plugs had to be popped off too. It was a very simple repair. The Sears guy wanted $395 total for the repair, and I did it myself for the price of the part on this site (around $90). Very pleased! Read more

Replaced faceplate of refrigerator. Read more

Unplug fridge. Use a Phillips head screwdriver to remove the single screw underneath the display. Also under the ledge you will see two slots - one on each side of the forward part of the ledge. Insert a flat-head screw driver and twist (either way) to release the plastic tabs. Once the tabs release you can pull the whole thing loose. Unplug the wiring connector and set the display face aside. Next TAKE A PICTURE OF WHAT YOU SEE WITH YOUR PHONE so you know how everything fits... Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more

Very helpful video from a link on your website (https://www.youtube.com/watch?v=EBIv0bxEhkE), and saved me a major repair bill. My journey started with an effort to replace just the water dispenser button, which failed because the fifth post on the back side of the button (not the four posts which hold the button in place--it's the extra rectangular piece visible near the repairman's pinkie finger at 3:04) had broken off, and it is this piece which reaches and moves the actuator for the water... Read more

The ice chute flap wasnt closing. 1. I turned off power 2, Pulled off facia around controls on freezer door,, you have to pull out the bottom part of the chute first , its clipped in 3. Disconnected the front panel 4. Unscrewed the next panel to allow access to the chute flap 5. Removed 1 screw holding complete flap and mechanism and replaced with new 6. Re installed all parts in reverse Problem was the chute flap had worn and was folding over on top edge when opened and then wouldnt return... Read more

So I ordered the face plate and other parts that went with it and fixed it myself. The repair man wanted around $600 to do it. I believe kt cost around $160 to fix it myself. Read more

First, your company web site is extremely helpful. If anyone chooses to do it theirself the ordering process is efficient, quick and easy. Things not found at many companies these days. The last time I ordered from you I got the part in the delivery system within 24 hours, but not so this time. Still I receive this part within 3 days, What I would expect normally when ordering from the internet. I'll never use any other appliance site unless you change for the worse, the customers are the... Read more

Replace dispenser micro switch. Also replaced broken faceplate and rusty screws. Appliance parts Pro YouTube video was helpful in diagnosis and disassembly. Parts arrived quickly. Read more

Buy the Cover Pad Assembly, reviewed youtube for a video, and following the instructions. Easy Read more

So I ordered the face plate and other parts that went with it and fixed it myself. The repair man wanted around $600 to do it. I believe kt cost around $160 to fix it myself. Read more

Once I found the hole for the spring arm to go in it took 1 min. Tip: make sure the spring is on the left side pin and, insert it First to insure the spring aligns then use a screw driver to pry out the Right side flange slightly to aide in inserting the right side pin into its hole Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

Replaced the actuator pad on the Whirlpool Gold Series, releasing the electronic menu pad to get to the water activator pad was the biggest hurdle. The release tabs are underneath the menu pad and you may feel as if you may break them when releasing them. They did not break but I did hold by breath. Read more