Washer Dispenser Parts

This bleach dispenser for a washing machine holds liquid bleach and releases it into the tub at the appropriate point in the cycle, helping dilute bleach and protect fabrics from contact with undiluted solution. What it does:

• Holds and meters liquid bleach until the machine calls for dispensing
• Helps ensure bleach mixes with water for even, diluted distribution
• Replace if cracked, clogged, or leaking
• Common symptoms include bleach not dispensing, bleach left in the cup, leaks around the dispenser area, or bleach spots on fabrics

• 1 bleach dispenser

• Disconnect power and turn off water before servicing
• Access and mounting vary by model; follow your service manual to reach the dispenser
• Detach hoses/clamps or fasteners, transfer any reusable hardware, and seat the new dispenser fully
• Reconnect, then run a test fill/rinse to check for proper dispensing and leaks

This dispenser drawer assembly replaces the pull-out detergent drawer on compatible washers. It restores smooth operation and proper dispensing of detergent, bleach, and fabric softener to help prevent leaks, residue build-up, and poor cleaning results.

• Holds and meters detergent, bleach, and fabric softener into the wash at the correct time
• Helps resolve no or incomplete dispensing of additives
• Common fix for a stuck, hard-to-open/close, or cracked drawer
• Can address water leaking or overflowing from the dispenser area

• Disconnect power and turn off water before servicing
• Fully extend the drawer, press the release tab, and remove the old drawer
• Align and slide the new drawer into the rails until it clicks into place
• Run a quick cycle to check for leaks

Color: white. Measures about 5-1/2 inches in diameter, and 6 inches high.

This dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle for consistent cleaning results. Replacing a worn dispenser restores reliable dosing so each wash performs as designed. What it does:

• Holds detergent and keeps it contained until dispensing
• Opens the detergent cup door at the programmed time in the cycle
• Directs detergent into the wash stream for even distribution
• Helps prevent poor cleaning caused by early loss or failure to dispense

• 1 detergent dispenser assembly

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; support wiring and insulation as you work
• Release mounting tabs/screws, transfer the wiring connector, seat the new dispenser evenly, and tighten fasteners uniformly
• Run a quick cycle to check for leaks

This small cover cap conceals an exposed fastener or opening on your appliance, restoring a clean, finished look. It also helps protect the area from dust and splashes for a tidy, long-lasting installation.

• Covers and protects an open screw hole or attachment point on a panel or door
• Restores a clean, factory appearance
• Helps keep dust and moisture out of the opening
• Common signs it's needed: missing cap, cracked/broken cap, loose cap, won't stay clipped

• Disconnect power (and water, if applicable) before servicing exterior panels or doors
• Note the cap's orientation and any retaining tabs before removal
• Use a plastic pry tool to gently release the old cap; press the new cap until fully seated
• Avoid forcing the cap or overtightening any underlying fastener to prevent damage

This bleach dispenser stores liquid chlorine bleach and automatically dilutes and releases it at the correct point in the wash cycle. Replacing a cracked or clogged dispenser helps stop leaks, protect fabrics, and restore consistent bleaching performance.

• Holds bleach and siphons it into the tub at the proper time in the cycle
• Helps prevent undiluted bleach from contacting fabrics early
• Direct replacement for a dispenser that is cracked, warped, or clogged
• Address symptoms such as bleach remaining in the cup, dispensing too soon, leaks near the dispenser area, or fabric spotting

• Disconnect power and turn off water before servicing
• Access the dispenser through the top/console area; remove fasteners and detach connected hose(s)
• Transfer any hoses, clamps, and mounting hardware from the original part; ensure all connections are fully seated to prevent leaks
• Run a test/rinse cycle to check for leaks

This door-mounted dispenser stores detergent and rinse aid and releases them at the right time in the cycle to help deliver clean, spot-free dishes. Replace a broken, leaking, or jammed dispenser to restore proper detergent release.

• Holds detergent and rinse aid and dispenses them during the wash cycle
• Supports consistent cleaning performance by timing chemical release
• Detergent cup won't latch or open
• Rinse aid doesn't dispense or leaks from the dispenser
• Detergent remains in the cup after the cycle

• Disconnect power and turn off the water supply before servicing
• Remove the inner door panel to access the dispenser
• Disconnect the wire harness, release locking tabs/fasteners, and install the new unit flush to the door
• Clean the sealing surface; tighten fasteners evenly and run a test cycle to check for leaks and proper dispensing

The Dispenser is an OEM part for Whirlpool washing machines. It holds and dispenses detergent for each wash load through the drawers located on the washer's console panel. 

Symptoms of a bad dispenser include:

• Improper or incomplete dispensing of detergent
• Detergent residue accumulated inside the dispenser 
• Drawers not opening or closing as intended

Causes of a dispenser failure can be due to worn components, mineral buildup interfering with mechanics, or damage from moisture exposure over time. 

Replacing with a new OEM dispenser restores optimal detergent delivery for every cycle. This ensures clothes are fully cleaned and rinsed without risk of detergent residue.  

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Color: White
 

This dispenser drawer holds and guides detergent, bleach, and fabric softener into the washer at the correct cycle time. Replacing a worn drawer helps prevent leaks, residue buildup, and improper dispensing that can affect wash results.

• Channels detergent, bleach, and softener from the 3-compartment tray into the wash
• May help when detergent remains in the drawer, leaks from the tray, or additives dispense inconsistently
• Restores smooth opening/closing and proper alignment of the dispenser tray

• Unplug the appliance and shut off water supply before servicing
• Pull the drawer out and release the locking tab to remove; reverse to install
• Transfer any reusable inserts from the old drawer if applicable
• Check for residue in the dispenser housing and clean before reinstalling

This is a replacement refrigerator storage drawer. It restores smooth sliding and dependable storage when the original drawer is cracked, warped, or missing, helping you keep items organized and easy to access. What it does

• Provides enclosed storage for food items inside the refrigerator
• Slides on the existing rails for easy access and organization
• Helps keep contents visible and separated from other items
• Common failure symptoms: cracks, broken tabs, drawer falling off tracks, hard to open/close

• 1 drawer

• Disconnect power and remove items from the drawer area before starting
• Fully extend and lift to remove the old drawer; clean the tracks
• Align the new drawer with both rails and slide it in evenly
• Do not force; ensure tabs and tracks are properly seated

This is the siphon insert for the washer dispenser's bleach and softener compartments. It restores proper siphoning so additives empty at the right time and helps reduce standing water or residue in the drawer.

• Creates the siphon action that draws bleach and fabric softener from their cups during the rinse cycle
• Promotes complete dispensing and consistent rinse performance
• Helps minimize leftover liquid and residue buildup in the dispenser
• Typical symptoms include bleach or softener remaining after the cycle, standing water in the cups, or weak/irregular dispensing

• Disconnect power and turn off water before servicing
• Remove the dispenser drawer; lift out the old siphon from the bleach/softener cup
• Clean any debris in the cup; firmly seat the new siphon, aligned per the cup markings
• Reinstall the drawer and run a rinse cycle to verify proper draw and no leaks

This dispenser handle assembly replaces a broken, loose, or missing handle on your appliance's dispenser. It restores a solid grip and proper actuation so the dispenser opens or operates smoothly and looks clean again.

• Provides the user grip/actuator for the dispenser mechanism
• Enables smooth opening or activation of the dispenser
• Helps ensure consistent operation and a clean finished look
• Common symptoms: cracked or missing handle, loose/wobbly handle, hard-to-open dispenser, handle won't stay attached

• Disconnect power; if working near water lines, shut off the water supply
• Open access to the dispenser area; retain and reuse any mounting screws/clips
• Transfer any reusable trim or small parts from the old handle if applicable
• Align and secure the new handle; test operation before reassembly

Color: White

The Dispenser Drawer Assembly is an OEM component specifically designed for Whirlpool washers. It houses detergent and fabric softener during cycles.

Causes of a faulty assembly can include warping of the plastic base from heat and chemicals over many loads. Small cracks may develop in the detergent trays.  

Symptoms of a bad dispenser drawer assembly include: 

• Leaks from cracked or misaligned drawers polluting washer interiors  
• Difficulty closing or securing the assembly properly
• Premature deterioration inhibiting reliable cycles 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.

Color: White

This replacement drawer restores a clean, organized storage space inside your refrigerator. It provides a smooth, secure place to hold items so you can access contents easily and maintain the appliance's intended capacity and layout. What it does

• Slides on factory rails/guides to organize food and contain spills
• Restores lost storage capacity when the original drawer is damaged or missing
• Helps contents stay properly supported and easy to access
• Common symptoms: cracked/broken bin, hard-to-slide or misaligned drawer, drawer falls out

• One drawer

• Power down the appliance if working near lights/fans; wear cut-resistant gloves
• Remove items, then lift and pull the old drawer straight out
• Inspect and clear/repair rails or guides before installing the new drawer
• Align with the tracks and slide in until fully seated; do not force