Whirlpool Dishwasher Parts

My Whirlpool dishwasher has a silver ware basket in the door that kept coming apart. It was driving me crazy. I Google the problem and found this wonderful site. In 2-3 days my sanity was restored. Opened the box and put the new basket in place. Much less expensive than replacing the dishwasher! Bravo! Read more

Ordered new wheel assembly, which came in about a day and a half. The broken assembly was on the left front so I only had to slide the dishwasher out just enough to expose the two mounting screws on the outside of machine.When you remove the old assm there are two rubber washers on the back side. If you didn't order new ones,remember to remove them from broken assembly and install them onto the new piece.Overall this is an easy fix and took about ten minutes including pulling the machine away... Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

Tipped the dishwasher on to its front, loosened the drain hose clamp and pulled the hose off. Then unscrew the fill hose which looks like a garden hose adapter. Cut the zip tie on the drain hose and take note of how both hoses are routed, then pull both hoses out the back of the dishwasher. Insert new hoses and route them correctly and hook everything back up. Couple of notes, I didn't have to take off the outer cabinet to do this repair. Get plenty of towels because a lot of water can get... Read more

I replaced the rear tube that feeds water to the top and middle spinners, and this appears to have fixed the problem. The middle spinner, which is attached to the bottom of the top rack, has a tube that connects to a hole in the middle of the rear tube.This hole has a rubber flap and I noticed that this flap was wide open. The tube under the tray has a straight edge protruding from it at the back. This edge pushes the flap open and I suspect that when the water is flowing, this edge rotates... Read more

Removed torx screws attaching stainless liner to outer stainless door. Lift off inner door and carefully separate the electronic components from where they snap into the control panel. Relocate electronic components to the new control panel. Reattach the inner liner with the torx screws. It is helpful to have an extra set of hands to hold the control panel while making the electronics swap to avoid pulling on the wiring harness. For door balance kit I just followed the video, straight forward. Read more

Replaced user interface reinstalled front cover and added in affresh and ran a cycle. Works like a dream now! Read more

Ordered exact part & installed Read more

Replaced the right and left front upper dish rack wheels. The best part was I ordered the parts Monday and had them first thing Tuesday morning. Read more

Tried bending the strike to get a firmer grip, but no luck. Replaced the door latch and strike. Washer is about ten years old. You can feel the new catch has a more positive engagement. When you replace the strike, be sure not to tilt it downward in front. It will go in the way but it will keep the door from closing. Not sure I needed to replace the strike but didn't want to risk more downtime. Read more

1, Removed roller tray front stoppers from each side. 2. Pulled out empty top rack from dishwasher. 3. Removed existing top rack roller. 4. Inserted new roller where old one was located. 5. Repeated for each roller. 6. Inserted top rack back into dishwasher. 7. Enjoyed using both racks again!! Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more

Removed and replaced diverter motor. Ops check good, no more leaking. I'm guessing the seal was the problem but diverter ruined (water residue) from leaking over the last 5 years??? This seal is only available if you buy the tub so followed another review - removed diverter then gently pried out the seal, cleaned and then lubed with silicone grease. Also turned the seal 180 degrees or the opposite way before reinstalling the diverter and then wrapping it all back under the counter. Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

I ordered a new detergent dispenser and control assembly, watched a few videos on you tube and dived in. The repairs were pretty simple once I got started and while I was doing this I went the extra step and cleaned out the drain. I would suggest doing this annually. Pretty simple to do and only 5 screws to get to the drain and the grinder. I found plastic and several other things that would not allow the dishwasher to drain properly and probably part of the problem of dishes not getting... Read more