Whirlpool Dishwasher Parts

The odor in the dishwasher was due to scum buildup in the walls, the racks, and in the lower part of the drain below the lower rotating arm. One of the valves in the vertical tube was stuck in the open position; since the valves cannot be replaced, the entire tube needed replacement. The check valve probably needed no replacement, but once I opened the bottom part, I decided to replace it anyway. I used this Youtube video to replace the tube, open and clean the drainage part of the washer: ... Read more

Replaced sump, wash pump, drain pump, diverter motor, and thermostat. Read more

Replaced filter. It works great now, no more brown spots. Read more

Purchased door springs from Appliance Parts pros.com, installed them and door on our Dishwasher was back to normal, Had to pull out dishwasher from under cupboard to get to springs, as they were on the sides of the dishwasher. Read more

Replaced sump because the seal is not sold separately. You will need a skinny clamp after cutting the original swaged clamp off. Also Had to replace the cover as its seal is not sold separately either. Used dish soap on seals during assembly. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

First tried replacing the seal around the door as that was the simple and most logical fix. Still leaked. Removed the front and upper panel to inspect. Found calcium deposit running down from under the Air Vent Assembly and wet behind the black stick-on insulation. Easy to trace the leak to the bottom of the door. => Ordered new Air Vent Assembly, gasket and Vent Deflector. Parts arrived. Took 5 minutes to remove upper panel. Removed the two wires from the Air Vent Assembly. Inserted a... Read more

We purchased the electronic control board (for 1/2 of what the technician wanted for the part), opened up the door to the dishwasher, took out the old board and put in the new one. It was a 15 minute repair and we saved almost $300 doing it ourselves! (Thanks to AppliancePartsPros.com and YouTube!) Read more

Checked online with app and figured out the most common cause of the problem after checking the most obvious causes. Ordered the fuse received on the second day. Installation was very simple and the dishwasher was again functional. Read more

Screwed the new spray arm on. This dishwasher has been through 2 control panels, a spray arm, rack roller assembly, rollers, and far too much of my time, patience, and money. I'll never purchase another KitchenAid product. Read more

• Touchpad does not respond

Most of the instructions you find online are for a different type of coupler that pops off. This model is different, as the coupler unscrews. I found a video for this specific model blender and I'll summarize below: Turn the blender over so the bottom of the blender is facing up You have to pop the bottom rubber feet off. Take off the four screws on the bottom of the blender Lift the bottom of the blender up and off. This may take two people. You'll need a heavy duty wrench under... Read more

Ordered new wheel assembly, which came in about a day and a half. The broken assembly was on the left front so I only had to slide the dishwasher out just enough to expose the two mounting screws on the outside of machine.When you remove the old assm there are two rubber washers on the back side. If you didn't order new ones,remember to remove them from broken assembly and install them onto the new piece.Overall this is an easy fix and took about ten minutes including pulling the machine away... Read more

• Noisy

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

Easy fix. simple assembly Read more

Tipped the dishwasher on to its front, loosened the drain hose clamp and pulled the hose off. Then unscrew the fill hose which looks like a garden hose adapter. Cut the zip tie on the drain hose and take note of how both hoses are routed, then pull both hoses out the back of the dishwasher. Insert new hoses and route them correctly and hook everything back up. Couple of notes, I didn't have to take off the outer cabinet to do this repair. Get plenty of towels because a lot of water can get... Read more