Whirlpool Parts

Complete drain pump and motor assembly that removes water from the washer during drain cycles, restoring reliable draining and preventing standing water for trouble-free spin and dry cycles. What it does:

• Pumps water out of the washer tub during drain cycles to help the washer complete drain and spin operations.
• Helps address common symptoms like a washer that won't drain, leaves water in the tub, or makes grinding/humming noises from the pump area.
• Replaces the original drain pump/motor unit to restore normal pump operation when the old unit is worn, clogged, or failing.

• One pump and motor assembly.

• Disconnect power and shut off water to the appliance before beginning any service.
• Drain any remaining water from the tub or hoses to avoid spills; keep towels or a shallow pan handy.
• Note or photograph hose and wiring connections before removal to ensure correct reassembly.
• Inspect pump mounting gaskets, hose clamps and hoses; replace damaged seals to prevent leaks.

This pump and motor assembly replaces the dishwasher's pump to restore proper water circulation and draining. It helps clear standing water and maintain wash performance when the original unit is worn or leaking. What it does:

• Drives water flow for normal wash cycles and pumps wastewater out during drain
• Restores proper draining when the dishwasher leaves water in the tub
• Reduces or eliminates grinding, humming, or squealing noises caused by a failing pump motor
• Helps resolve common drain-related error codes and poor wash results tied to low circulation

• One pump and motor assembly

• Disconnect power and water supply before beginning any repair
• Expect residual water in the tub and hoses; have towels or a pan ready
• Handle electrical connectors and hoses gently; replace any damaged clamps or seals
• Test the dishwasher on a short cycle after installation to ensure proper drain and flow

This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:

• Drives water through the drain pump so the washer can empty properly
• Worn or broken impellers can cause slow or no draining and standing water
• May produce unusual pump noise or vibration when damaged
• Helps prevent motor overload by maintaining proper water flow

• One drain impeller

• Disconnect power before accessing the pump assembly to avoid electric shock
• Inspect the pump housing and fasteners; replace any damaged clips or seals as needed
• Reassemble pump and test a short drain cycle before completing the repair

This motor-pump assembly replaces the washer's drain pump to restore reliable water removal and reduce leaks. It mounts to the tub and handles draining so your cycle can finish and clothes can spin out properly. What it does:

• Pumps water out of the washer during drain cycles to allow proper spin and cycle completion
• Helps prevent standing water and reduces the chance of overflow or tub leaks
• Stops humming, grinding, or no-drain symptoms caused by a failed pump motor
• Works as the integrated motor and pump unit that attaches to the washer tub

• Disconnect power and water before servicing; follow all safety precautions
• Basic hand tools required; access may require removing front or rear service panel
• Inspect and reinstall hoses and clamps securely to prevent leaks

The Pump-Drain is an OEM part for Whirlpool dishwasher modules. It serves as the water pump that actively removes dirty water from the wash chamber, directing it to the garbage disposal or home drainage system. 

Causes for a faulty Pump-Drain can stem from mineral buildup clogging impeller fins over time. Wear and tear on seals or electrical failure of motor components are also possible from prolonged usage.  

Symptoms of a bad Pump-Drain include:

• Incomplete draining or water remaining after cycles
• Strange gurgling or grinding noises during drain phase   
• Leaks detected around the drain hose connection
• Soap scum or film left inside from inadequate rinsing

This OEM replacement part works with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore dishwasher models as well. 

This water pump moves wastewater out of the appliance so cycles finish and the tub stays clear of standing water. It replaces a failed pump to restore normal draining and cycle completion. What it does

• Pumps out drain water so the appliance can complete wash or rinse cycles
• Stops leaks from a damaged pump housing or worn seals
• Common symptom: appliance won't drain or has standing water after a cycle
• Can reduce or stop unusual grinding or humming noises coming from the pump area

• Disconnect power and water supply before beginning any repair
• Inspect hoses and seals for damage and replace if necessary when changing the pump
• Install with correct mounting orientation and secure electrical connections per OEM instructions

This pump and motor assembly circulates and drains dishwasher water to ensure proper washing and draining. It restores normal water movement so dishes get cleaned and the tub drains after a cycle. What it does:

• Circulates wash water through spray arms for effective cleaning.
• Pumps water out of the tub during drain cycles.
• Can cause noisy operation, poor cleaning, standing water, or failure to drain when defective.
• Works as the combined sump/pump motor unit used in many Whirlpool-family dishwashers.

• Disconnect power to the appliance before beginning any repair to avoid electric shock.
• Turn off the water supply and remove lower access panels to reach the pump/sump area.
• Handle as a single assembly; check and clear any debris or foreign objects from the sump and inlet before reinstalling.

The Pump Housing is an OEM part for Whirlpool dishwashers. As a central component, it contains the circulating pump that drives wash water through spray arms for thorough cleaning.

Symptoms of a bad pump housing include:

• Puddles or leaks from under the dishwasher main unit
• Limited or no water pressure to upper and lower spray arms  
• Water that does not properly drain at the end of a cycle
• Drying issues caused by residual water collection 

Causes can be cracks that develop from regular pump cycling stresses over time, or impact damage compromising seals and gaskets.

This OEM Whirlpool part is also compatible with some KitchenAid, Jenn-Air, and GE dishwashers.

The Drive Motor is an OEM component for Whirlpool electric and gas dryers. It powers the rotating drum and tumbling of clothes during drying cycles.

The drive motor may fail due to wear and tear over time, electrical issues, or damage to the motor's internal components. Regular use, exposure to lint and dust, and overheating can contribute to motor failure.

Symptoms of a bad drive motor include:

• The dryer drum not spinning
• Unusual noises such as humming or buzzing
• The dryer not starting
• The motor overheating or shutting off

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Circulation Motor is an OEM part for Whirlpool dishwashers. It is responsible for pumping water through the spray arms to ensure thorough cleaning of dishes during the wash cycle. This motor helps maintain consistent water pressure and flow, crucial for effective dishwashing performance.

Over time, the circulation motor can fail due to factors such as motor wear, electrical issues, or blockages that cause the motor to overheat or become damaged. Regular use and the buildup of debris or hard water deposits can also contribute to motor failure.

Symptoms of a bad circulation motor include:

• Poor cleaning results
• Unusual noises during the wash cycle
• Water not circulating properly
• Dishwasher not completing cycles

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Pump Assembly is an OEM part for Whirlpool washing machines. This part drains water from the washer during the wash and spin cycles. The water pump assembly ensures that water is efficiently removed from the drum, preventing overflows and ensuring proper rinsing and spinning of clothes.

Causes of a bad water pump assembly can include debris or foreign objects clogging the pump, motor failure, or damage to the impeller or seals.  

Symptoms of a bad water pump assembly include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Leaks from the pump area
• Error codes related to draining issues

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This part is responsible for circulating water during the wash cycle and draining water at the end of the cycle.  

Causes of a bad assembly can include blockages from debris, electrical failures, or wear and tear from regular use.  

Symptoms of a bad Pump and Motor Assembly include:

• Dishes remaining dirty after a wash cycle
• Water not draining properly from the dishwasher
• Unusual noises during operation
• Error codes related to water flow or pump performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is a durable pump and motor assembly for dishwashers. The purpose of the pump and motor is to pump water that goes through the spray arms when the dishwasher moves through a cycle. If the pump and motor assembly isn't working correctly, it could lead to dishes that are dirty after a cycle is complete. Other signs of a bad pump and motor include pooling water after a cycle and whining noises.If the pump and motor assembly need to be replaced, make sure the dishwasher is unplugged. Use a pair of work gloves to protect the hands throughout the process. Close the water supply valve and disconnect the drain line. Replacing the pump and motor assembly may require tilting the dishwasher on its side to disassemble the components that are in the way of the replacement. Once the pump and motor have been removed, install the new parts and reassemble the dishwasher before use.Created for use with dishwashers by KitchenAid, Kenmore, and Whirlpool, this pump and motor assembly is a genuine OEM replacement part. It is sold as a single part. This component is directly sourced from the manufacturer.

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.