Washer Knob, Dial & Button
Genuine Ge part
By: Ge
Part Number: WH01X10310
Replacement timer control knob assembly for washers. Installs on control panel to select cycles and settings. Needed when knob is cracked, broken, worn, or won't grip timer shaft.
Do-It-Yourself Stories from Customers like You
The control knob spun freely without engaging to select cycle Polly H. • Glen Allen , VA • November 11, 2014
I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle.
https://www.youtube.com/watch?v=cQwLtRcHx9k
Read more
More
$9.95
- Compare At:
-
$11.74
- You Save:
-
$1.79
Genuine Ge part
By: Ge
Part Number: WE01X20378
Replace a cracked, broken, or missing control knob on your washer or dryer. This plastic dial installs on the front control panel for cycle selection.
This part fixes the following symptoms
-
Doesn't shut off
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
Cracked start knob on my dryer Joe T. • Cape Coral , FL • August 12, 2014
Found the part through appliancepartspros.com The part was the cheapest of several web sites. although shipping for such a small part was steep ($7.95 If I was purchasing bigger parts or heavier parts..the flat rate cost would be a bargain.
The part arrived the next day and fit perfectly. In additon; obviously the original manufactured part was not holding up well as the new part had a metal reinforcement band that will prevent the cracking in the future.
Read more
More
$27.49
- Compare At:
-
$32.71
- You Save:
-
$5.22
Genuine Ge part
By: Ge
Part Number: WH1X2721
Control knob and clip assembly for dryer or washer. Attaches to control shaft to set cycles and settings. Replace if cracked, broken, or missing.
Do-It-Yourself Stories from Customers like You
Noisy(thump thump sweaks) when dryer was in operation Michale R. • Sinclair , WY • January 08, 2015
Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side.
Read more
More
$12.44
- Compare At:
-
$18.05
- You Save:
-
$5.61
Genuine Ge part
By: Ge
Part Number: WH11X10049
Timer dial knob for washers. Installs on control panel to select wash cycles. Replace if knob spins freely, teeth are worn, or it won't engage cycles.
Do-It-Yourself Stories from Customers like You
The control knob spun freely without engaging to select cycle Polly H. • Glen Allen , VA • November 11, 2014
I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle.
https://www.youtube.com/watch?v=cQwLtRcHx9k
Read more
More
$10.95
- Compare At:
-
$13.03
- You Save:
-
$2.08
Genuine Ge part
By: Ge
Part Number: WH1X2754
Replacement timer knob assembly for washers. Installs on the control panel timer shaft. Needed when original knob is cracked, broken, or missing.
Do-It-Yourself Stories from Customers like You
Broken timer knob Michael K. • Indialantic , FL • October 03, 2014
Easily replaced the knobs
Read more
More
$12.53
- Compare At:
-
$14.91
- You Save:
-
$2.38
Genuine Frigidaire part
By: Frigidaire
Part Number: 134844410
The Selector Knob is an OEM part for Frigidaire appliances designed for use on various models of washers and dryers. This knob enables users to select different cycles and settings, providing essential control over the appliance's operations.
Symptoms of a failing selector knob include:
- The knob failing to engage or change settings
- Difficulty in turning or a lack of resistance
- Visual signs of wear such as cracks or breakage
Causes of selector knob deterioration typically involve continuous mechanical use, accidental impacts, or exposure to harsh environmental conditions that can weaken the plastic.
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
This part fixes the following symptoms
-
Won't start
-
Touchpad does not respond
See more...
Do-It-Yourself Stories from Customers like You
Dryer knob was broken Karen H. • League City , TX • July 01, 2014
Replaced old knob with new knob
Read more
More
$53.95
- Compare At:
-
$64.20
- You Save:
-
$10.25
Genuine Ge part
By: Ge
Part Number: WH01X10060
The Selector Knob is an OEM part for GE washing machines. This knob is used to choose different wash cycles and settings on the control panel, allowing users to customize their laundry preferences. It is designed to fit securely onto the control shaft and provide smooth operation for selecting various options.
Over time, selector knobs can wear out or become damaged due to frequent use or accidental impacts. Causes of a bad selector knob can include cracked or broken plastic, stripped or worn-out internal components, or a loose fit on the control shaft.
Symptoms of a bad selector knob include:
- Difficulty in turning the knob or selecting settings
- Knob spinning freely without changing settings
- Knob falling off or feeling loose
- Visible cracks or damage on the knob
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Broken selector knob Philip O. • Gastonia , NC • June 01, 2014
I ordered a new knob and it arrived very quickly. The repair was simple and I will use appliance parts pros again should I need to. Thank you.
Read more
More
$20.22
- Compare At:
-
$24.06
- You Save:
-
$3.84
Genuine Ge part
By: Ge
Part Number: WH01X10313
Replacement control knob for washing machines. Installs on the control panel to select cycle and temperature settings. Needed when cracked or broken.
Do-It-Yourself Stories from Customers like You
Dryer was not heating on the timed dry side but heating on the other side of timer Iris H. • Canal Fulton , OH • February 22, 2015
Replaced the timer
Read more
More
$9.95
- Compare At:
-
$11.84
- You Save:
-
$1.89
Genuine Ge part
By: Ge
Part Number: WH11X10033
Replaces the cycle selector dial assembly on your washer control panel. Needed when the dial is cracked, broken, or won't turn properly with the timer.
Do-It-Yourself Stories from Customers like You
Control knob did not work Murphy P. • Jonesborough , TN • April 14, 2015
Replaced both the control knob, and the dial assm. the videos were great, I was getting ready to order the whole assembly. video saved me over 100 dollars. thanks.
Read more
More
$37.95
- Compare At:
-
$45.16
- You Save:
-
$7.21
Genuine Ge part
By: Ge
Part Number: WH11X10015
Replacement timer dial for washers. Installs on the control panel to set wash cycles. Needed when original dial is cracked, broken, or worn smooth.
Do-It-Yourself Stories from Customers like You
Broken timer knob Michael K. • Indialantic , FL • October 03, 2014
Easily replaced the knobs
Read more
More
$34.73
- Compare At:
-
$41.33
- You Save:
-
$6.60
Genuine Ge part
By: Ge
Part Number: WH01X10314
Control knob assembly for washer timer/cycle selector. Restores secure grip when original is cracked, stripped, or broken. Attaches to timer shaft.
Do-It-Yourself Stories from Customers like You
The timer washer knob would not turn the dial assembly. Daniel H. • Deridder , LA • June 12, 2021
I replaced the Timer knob components. Removing the cover that contains the Timer was simpler than I anticipated. Just remove the screws on the top of the back of the machine. Hold the cover and lift up and push to the left (facing the front of the washer). Removed the Timer Knob Clip with small needle-nose pliers. Grasped the Timer and turned counterclockwise to remove and unplugged the wiring clip. The timer is seated to the cover and held securely in place with one screw. I seated the new...
Read more
More
$16.38
- Compare At:
-
$19.49
- You Save:
-
$3.11
Genuine Frigidaire part
By: Frigidaire
Part Number: 134886700
The Timer Knob Assembly is an OEM replacement part for Frigidaire electric dryers. This assembly incorporates the timer dial, stem, and mounting components that allow users to set desired drying periods.
Causes of a faulty timer knob include wear and tear of internal gears from regular cycle selections. Damage to the outer dial or stem connection points may also occur.
Symptoms include:
- Inability to rotate timer dial through full drying options
- Timer selections not initiating or maintaining set programs
- Dial detaching from the front panel during adjustment
This OEM Frigidaire replacement part is compatible with Electrolux, Gibson, and various Kenmore dryer models as well.
Do-It-Yourself Stories from Customers like You
Dryer timer would not turn and knob broke from the strain Bruce B. • Birmingham , AL • October 17, 2014
I ordered the timer and knob on Monday, they arrived around noon on Tuesday, and within an hour I had them installed and back in business. I was amazed how quickly the parts got here. The online video showing the procedure step by step was very helpful. Instead of disconnecting all the wires and having to keep up with which one went where, I moved each wire one by one and made sure I didn't get any of them in the wrong place. The only thing that slowed me down a bit was seeing which side of the...
Read more
More
$50.43
- Compare At:
-
$60.01
- You Save:
-
$9.58
Genuine Whirlpool part
By: Whirlpool
Part Number: W10807860
The Knob is an OEM part for Whirlpool washers. This part allows users to select and control the various wash cycles and settings by turning the knob to the desired position. It fits securely onto the washer's control shaft, providing an intuitive and reliable interface for managing the washing machine's functions.
Causes of a bad knob can include regular wear and tear, damage from repeated use, or breakage due to accidental impact.
Symptoms of a bad knob include:
- The knob not turning smoothly or becoming difficult to turn
- The knob slipping off or not staying securely on the control shaft
- Inaccurate or unresponsive cycle and setting adjustments
- Visible cracks, breaks, or wear on the knob
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Knob and timer knob Charles B. • Sioux Falls , SD • October 01, 2018
Watched the video and completed repair as shown
Read more
More
$51.46
- Compare At:
-
$60.72
- You Save:
-
$9.26
Genuine Ge part
By: Ge
Part Number: WH11X10047
Labeled control ring for your washer's control panel. Replace when the original dial becomes cracked, stripped, worn, or the cycle indicators are unreadable.
Do-It-Yourself Stories from Customers like You
The timer washer knob would not turn the dial assembly. Daniel H. • Deridder , LA • June 12, 2021
I replaced the Timer knob components. Removing the cover that contains the Timer was simpler than I anticipated. Just remove the screws on the top of the back of the machine. Hold the cover and lift up and push to the left (facing the front of the washer). Removed the Timer Knob Clip with small needle-nose pliers. Grasped the Timer and turned counterclockwise to remove and unplugged the wiring clip. The timer is seated to the cover and held securely in place with one screw. I seated the new...
Read more
More
$7.95
- Compare At:
-
$9.38
- You Save:
-
$1.43
Genuine Frigidaire part
By: Frigidaire
Part Number: 131761704
Rotary control knob that fits onto the control shaft to select settings. Replace if your original knob is cracked, broken, worn, or missing.
Do-It-Yourself Stories from Customers like You
Broken knob Fred S. • Los Gatos , CA • August 29, 2014
Found the correct part number, ordered a replacement and replaced it
Read more
More
$32.74
- Compare At:
-
$38.96
- You Save:
-
$6.22
Genuine Frigidaire part
By: Frigidaire
Part Number: 134191800
This control knob replaces a worn, cracked, or missing range/stove dial so you can select heat and settings with a secure grip and clear position indicator. It restores normal operation of the control shaft. What it does:
- Fits onto the control shaft to turn the burner/oven setting and indicate the selected position.
- Restores a solid grip and visible pointer for precise adjustments.
- Common symptom fix: knob is loose, stripped, cracked, or missing and won't turn or hold a setting.
- Helps avoid accidental setting changes from a damaged or worn knob.
What's included: One control knob. Install notes:
- Disconnect power to the appliance before service to avoid shocks or accidental heating.
- Pull the old knob straight off the control shaft; line up splines and push the new knob onto the shaft until fully seated.
- Do not force or hammer the knob onto the shaft; if it does not seat easily, verify spline alignment.
- If the control stem or switch is damaged, replace the stem/switch assembly rather than forcing a knob.
Do-It-Yourself Stories from Customers like You
Broken knob. Mark S. • Denver , CO • June 20, 2020
Ordered the part and replaced it when I received it.
Read more
More
$76.95
- Compare At:
-
$92.34
- You Save:
-
$15.39