Parts for Kenmore Elite 79641783710: Cabinet & Control Panel Assy Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This holder is a small mounting bracket that secures internal components and keeps assemblies aligned for reliable operation. It replaces a worn or broken bracket to stop rattling and prevent parts from shifting. What it does

• Secures and positions nearby components or assemblies to maintain correct alignment
• Prevents vibration, rattling, or intermittent contact caused by a loose or cracked bracket
• Restores proper spacing so sensors, panels, or moving parts operate smoothly
• Helps prevent further wear or damage from misaligned parts

• One holder as shown

• Turn off power and disconnect the appliance before attempting any repairs
• Installation typically requires basic hand tools; save removed screws and clips for reassembly

This cover assembly replaces the tub cover that protects internal components and helps seal the wash compartment for proper operation. It restores the cabinet appearance and keeps water and debris away from the tub area. What it does:

• Forms the protective top/face of the tub area to prevent water spray and debris from reaching internal components.
• Helps maintain a proper seal and support for the tub and adjacent components.
• Commonly replaced when cracked, warped, or damaged by impact or excessive wear.
• Can reduce leaking and rattling caused by a broken or loose tub cover.

• Refer to the washer's service manual for step-by-step removal and reassembly instructions.
• Disconnect power and water supply before starting any repair.
• Handle the cover carefully to avoid scratching or bending mounting tabs.
• If fasteners, clips, or trim are damaged, replace them.

The Shipping Bolt Assembly is an OEM part for LG washing machines. It is essential for securing the drum during transport, preventing movement that could damage internal components.

Causes of a bad shipping bolt assembly can include improper removal or reinstallation, damage from handling, or deterioration if left in place during machine operation. When compromised, it can affect the stability and alignment of the drum.

Symptoms of a bad shipping bolt assembly include:

• Excessive vibration or noise during washing cycles
• Difficulty in moving or transporting the washing machine
• Drum misalignment issues
• Unusual movement or shifting of the machine during operation

This OEM LG part is also compatible with Sears/Kenmore models.

The Shipping Bolt is an OEM part for LG washing machines, designed to secure the washing machine's drum during transportation. These bolts are important for preventing damage to the drum and suspension system by immobilizing the drum, thereby avoiding any excessive movement or vibrations that could occur while moving the appliance. 

Causes of a bad shipping bolt can include improper removal during installation, damage from handling, or degradation over time if it was left in place during operation. A damaged or missing shipping bolt can lead to issues with the washing machine's drum alignment and overall stability.

Symptoms that indicate the shipping bolts need removal or installation include:

• Excessive noise or vibrations during operation, suggesting the bolts were not removed after installation.
• Damage to the washing machine's drum or suspension system after moving the appliance without the bolts properly installed.

This OEM LG part can also be used on Kenmore/Sears appliances. 

Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.

What it does

• Locks the tub and basket to limit movement in transit
• Helps prevent suspension damage and internal rattles while relocating
• Replaces missing, bent, or stripped transport bolts
• Useful for moves, storage, or service shipments

What’s included
One shipping bolt assembly (sold individually).

Install notes

• Unplug power and turn off water before service
• Insert through the rear panel into the designated mounting point; tighten snugly—don’t overtighten
• Do not operate the washer with shipping bolts installed; remove all bolts after placement
• Some models use multiple bolts and lengths—match count/positions to your owner’s manual

Usage tip
After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.

This lifter is a replacement drawer support that helps hold and guide a refrigerator/freezer drawer for smooth, even operation. Restores proper alignment and reduces sticking or uneven movement. What it does:

• Supports and stabilizes a sliding drawer so it opens and closes smoothly
• Helps maintain proper drawer alignment and load distribution
• Worn or broken lifters can cause sagging, binding, or uneven drawer movement
• Replaces damaged or missing lifter hardware to restore normal drawer function

• Disconnect power and empty the drawer before starting any repair
• Remove the drawer or access panel per your model's service instructions to reach the lifter
• Install the new lifter in the same orientation and secure any retaining clips or screws; do not force parts into place
• If fasteners or adjacent guides are damaged, replace them as well for a secure fit

This door hinge bracket mounts the hinge to the washer's front cabinet, keeping the door aligned so it closes and seals properly. A bent or broken bracket can lead to door sagging, poor latching, or leaks at the door.

• Secures the door hinge to the washer's front panel/cabinet
• Supports door weight to maintain alignment
• Helps preserve proper door-to-gasket contact for sealing
• Typical symptoms: door sags or rubs, won't close/latch, or water leaks at the door

• Disconnect power and shut off water before servicing.
• Support the door before removing hinge/bracket screws to prevent strain.
• Transfer the hinge to the new bracket and reinstall using existing hardware.
• Align the door and ensure latch engagement and gasket seal before fully tightening.

The Spider Arm is an OEM part for LG washing machines. As an important component linking internal mechanics, the spider arm connects the basket or tub to other components like the drive motor. It facilitates the spinning motion essential for washing cycles while also enabling water to properly agitate clothing. 

Symptoms of a bad spider arm include:

• The tub not spinning or spinning unevenly
• Vibration or noise issues arising from the center of the machine  
• Water not draining or agitating clothes as intended
•  premature wear on other connected parts over time

Causes of a bad spider arm can be regular use over several years, damage from excessively heavy loads, or impact from an object inside the tub. Not replacing a faulty spider arm can accelerate damage to other expensive parts. 

This LG replacement part is also compatible with Sears/Kenmore models. 

Customized machine screw for select washers that fastens specific assemblies and resists vibration. Replace a missing, stripped, or damaged factory screw to restore a solid, rattle-free fit and proper component alignment.

• Secures designated brackets, panels, or housings per the manufacturer's specifications
• Maintains alignment and stability under high-speed spin and vibration
• Replaces missing, corroded, or stripped hardware to stop looseness and noise
• Use when the original screw is worn, damaged, or lost

• Unplug the appliance and shut off water before servicing
• Support the component while removing/installing screws
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep screws organized—lengths and styles may vary by location

The Tub Bearing is an OEM replacement part for LG front-loading washing machines. This is the inner tube bearing that allows the tub to spin freely during the wash cycle.

Causes of a faulty tub bearing can include wear from repeated cycles, excessive vibrations putting strain on components, or foreign material intrusion into the bearing area.  

Symptoms include: 

• Noisy or grinding sounds emanating from inside the tub during operation
• Reduced spin efficiency causing wet clothes  
• Vibrations transferred to surrounding cabinetry

This LG replacement bearing restores smooth, quiet operation. Compatible with some Kenmore models as well, replacing it prevents potential tub damage from friction. 

The Tub Bearing is an OEM part for LG washing machines. It supports the washer drum, ensuring it spins smoothly and quietly during wash and spin cycles.

Common causes of a bad tub bearing include regular wear and tear from frequent use, exposure to heavy or unbalanced loads, and water damage from leaks. A faulty bearing can lead to noisy operation and reduced efficiency, potentially causing further damage to the washing machine.

Symptoms of a bad tub bearing include:

• Loud noises during the wash or spin cycles
• Excessive vibration or movement of the washer
• Difficulty in spinning or the drum not spinning at all
• Water leaks from the drum area

This OEM LG part is also compatible with Sears/Kenmore.

The Motor Rotor Bolt is an OEM part for LG washing machines. It secures the rotor to the motor shaft, playing a crucial role in the efficient functioning of the motor and ensuring the washer drum spins correctly during wash cycles.

Causes of a bad motor rotor bolt can include wear and tear from prolonged use, corrosion due to exposure to moisture, or damage from over-tightening or accidental impacts. A faulty motor rotor bolt can compromise the stability of the motor, leading to various operational issues.

Symptoms of a bad motor rotor bolt include:

• The washer drum not spinning or spinning irregularly
• Unusual noises during operation, such as banging or clunking
• The washer failing to complete cycles or stopping mid-cycle
• Visible wear or damage to the bolt or surrounding components

This OEM LG part is also compatible with Sears/Kenmore models.

The Rear Tub Gasket is an OEM part for LG washing machines. It provides a watertight seal between the rear tub and the front tub assembly, preventing water leaks during the wash and spin cycles. This gasket ensures that water remains contained within the drum, contributing to the overall efficiency and performance of the washing machine.

You should replace the rear tub gasket if it becomes worn out, cracked, or damaged. Causes of a bad rear tub gasket can include general wear and tear, mold or mildew buildup, and damage from foreign objects during washing.

Symptoms of a bad rear tub gasket include:

• Water leaking from the back of the washing machine
• Visible cracks, tears, or deformation in the gasket
• Mold or mildew buildup around the gasket area
• Unusual noises during the wash cycle indicating a loose or misaligned gasket

This OEM LG part is also compatible with certain models of Kenmore washing machines.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

The Outer Door Boot Seal Clamp is an OEM part for LG washing machines. This clamp secures the outer door boot seal, ensuring a tight seal to prevent water leaks during the wash cycle.

You should replace the outer door boot seal clamp if it becomes damaged or loses its tension, which can happen due to regular use, exposure to harsh cleaning agents, or physical wear and tear.

Symptoms of a bad outer door boot seal clamp include:

• Water leaks from the door area during the wash cycle
• Loose or shifting door boot seal
• Difficulty in closing the washing machine door securely

This OEM LG part is also compatible with Sears/Kenmore.

This balance weight secures to the appliance frame to add counterweight where needed, helping reduce vibration and stabilize moving parts for quieter, more reliable operation. What it does:

• Adds counterbalance to a drum, door or other moving component to reduce shaking and excessive movement during operation.
• Restores proper weight distribution to prevent off-balance conditions that can trigger vibration or noise.
• Typically fastens to the frame with mounting bolts to transfer and even out dynamic loads.
• A worn, loose or missing balance weight may be linked to loud banging, heavy vibration or uneven operation.

• Disconnect power (and water supply for washers) before starting any repair.
• Remove the appropriate access panels to reach the mounting location; keep fasteners for reassembly.
• Reinstall using the original mounting bolts and follow OEM torque recommendations when available.
• Inspect adjacent suspension, mounts and hardware while servicing.

This outer tub cover protects the washer's drum assembly and helps keep water and components contained during operation. It replaces a worn or damaged cover to restore proper sealing and prevent leaks or debris intrusion. What it does:

• Covers and protects the washer tub and internal components from water, lint, and foreign objects.
• Helps maintain proper alignment and sealing of the tub during wash cycles.
• Commonly replaced for visible damage, cracks, or when leaks appear around the tub area.
• Supports stable drum operation by keeping internal components enclosed.

• Disconnect power and turn off water supply before starting any repairs.
• Installation may require removing the cabinet or drum assembly; follow the service manual for step-by-step guidance.
• Handle the cover carefully to avoid scratching or bending mounting tabs.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

The Outer Tub Gasket is an OEM replacement part for LG front-load washers. Situated between the front and rear outer tubs, it forms a critical seal preventing water leaks during fills and cycles. Constructed from durable yet flexible rubberized material, this gasket withstands constant compression from tub movements.

Causes for replacement are cracks developing from years of flexing stresses, as well as distortions that compromise sealing integrity. Normal seal compression can also cause gradual wear of sealing material over time.

Symptoms of a faulty front-load outer tub gasket include:

• Puddles or drips of water between or behind the wash tubs
• Dried mineral deposits from leakages around tub connection points

This OEM LG part is also compatible with some Sears/Kenmore.

Washer screw

The Motor Stator Bolt is an OEM part for LG washing machines. This bolt secures the stator to the motor, ensuring the stability and proper functioning of the washing machine's motor assembly.

Causes of a bad motor stator bolt can include wear and tear over time, improper installation, or damage from over-tightening or impact. A compromised bolt can lead to instability in the motor, potentially affecting the washer's performance.

Symptoms of a bad motor stator bolt include:

• Unusual noises during the wash cycle
• Vibrations or shaking of the washer
• The motor not functioning properly or failing to start

This OEM LG part is also compatible with Sears/Kenmore.

This single wire harness connects electrical components to restore power and signal routing for the appliance. It replaces a damaged or worn harness to help re-establish reliable electrical connections. What it does:

• Transfers power and signals between control boards, sensors, and actuators
• Helps resolve intermittent operation, failure to start, or component non-response when caused by wiring faults
• Replaces frayed, burned, or connector-damaged wiring to restore proper circuit continuity
• Matches OEM connector types and routing for a direct-fit replacement

• One single wire harness as shown

• Power off and unplug the appliance before beginning any repair
• Verify the harness routing and connector orientation match the original before securing
• Use appropriate tools and avoid pinching wires; replace any mounting clips that are damaged

This inner door frame replaces the interior trim that secures the microwave door components and restores a finished appearance. It helps ensure the door closes cleanly and keeps internal door parts properly aligned for safe operation. What it does:

• Replaces a cracked, warped, or dented inner door frame that can allow rattling or misalignment
• Provides the mounting surface and support for inner door components and insulating layers
• Helps restore a flush door fit and reduce air/gap issues that cause improper sealing
• Reduces visible damage and improves the oven's cosmetic appearance

• One inner door frame

• Disconnect power (unplug or switch off circuit breaker) before servicing the door to avoid electrical shock
• Remove the outer door panel and inner components carefully; keep fasteners and insulating layers in order
• Handle glass and painted surfaces carefully to avoid breakage or scratches

This locker hook engages the appliance's latch/lock mechanism to keep the door securely closed during operation. Replacing a worn or bent hook restores reliable latching and helps prevent nuisance door/lock errors and cycle interruptions.

• Interfaces with the door lock/latch to secure the door during use
• Allows the safety interlock to confirm the door is closed
• Common symptoms: door won't latch or stay closed, needing to hold/push door to start, door/lock error messages
• Physical signs of failure: bent hook, worn contact surface, or cracked/broken mounting ears

• Disconnect power; turn off water supply if applicable
• Access the hook location on the door or cabinet/tub (varies by model); remove mounting screws/clips
• Transfer any reusable hardware; align the new hook so it mates cleanly with the latch/lock and tighten fasteners
• Close the door to verify smooth engagement before running a cycle

The Magnetic Door Plunger is an OEM part for LG washing machines. It is designed to securely hold the door in a closed position during the operation cycle, employing a magnet mechanism for enhanced reliability. The plunger ensures that the door latch is properly engaged, preventing the machine from running if the door is not closed correctly.

Causes of a bad Magnetic Door Plunger can include wear and tear from constant use, failure of the magnetic mechanism due to exposure to moisture or mechanical damage, or a misalignment that prevents the door from closing properly.

Symptoms of a bad Magnetic Door Plunger include:

• The washing machine door not staying closed during cycles.
• The machine failing to start due to a door sensor not detecting closure.
• Random pausing of the machine during operation if the door unlatches.

This OEM LG part is also compatible with Sears/Kenmore.

The Water Inlet Valve Assembly is an OEM part for LG washers. This assembly controls water intake into the washer tub, allowing for fill levels to be reached on selected cycles.

Causes of a bad water inlet valve can include gaskets drying out over time, sediment buildup slowing water flow, or damage to tubing connections.  

Symptoms of a bad water inlet valve include:

• Failure to fill properly or fill levels being too high/low  
• Leaks developing at tub or valve areas
• Fluctuating or unreliable water pressure  
• Repeated imbalance or water level sensor errors

Replacing with this OEM assembly ensures proper water levels are attained. Designed for dependable operations, it supports efficient cycle completions.

This OEM LG part is also compatible with Sears/Kenmore. Replace quickly to avoid further issues down the line.
 

The Hot Water Valve is an OEM part for LG washing machines. It regulates the flow of hot water into the wash tub during the appropriate cycles. The valve allows hot water to enter the wash tub to help wash clothes thoroughly and effectively at warmer temperatures.

Causes of a bad hot water valve include mineral or lime buildup inhibiting proper operation, worn internal components due to age and use, or damage from freezing during winter months.

Symptoms of a bad hot water valve include:

• Only cold water entering the wash tub, even on hot cycles
• Fluctuating hot water temperature during cycles
• Leaks from the hot water valve area
• Inability to select hot water temperature settings

This LG part is also compatible with some Kenmore models.

The Water Inlet Valve Filter Screen is an OEM part for LG washing machines. This filter screen is designed to fit inside the water inlet valve, ensuring that debris and sediment are filtered out before the water enters the washing machine. This helps maintain clean water flow and protects the internal components of the washing machine from damage caused by particles.

Causes of a bad Water Inlet Valve Filter Screen can include clogging due to sediment buildup, damage from high water pressure, or wear and tear over time. Regular inspection and cleaning can help prolong the life of the filter screen.

Symptoms of a bad Water Inlet Valve Filter Screen include:

• Reduced water flow into the washing machine
• Long fill times or failure to fill
• Sediment or debris found in the wash water
• Error codes related to water intake issues

This OEM LG part is also compatible with Sears/Kenmore.

The Float Assembly is an OEM part for LG washing machines. This part monitors and controls the water level within the appliance. It's a safety feature that prevents water overflow and potential flooding, contributing to the efficient operation of the washing machine by maintaining the correct water level for each cycle.

Causes of a bad Float Assembly can vary from simple blockages that prevent the float from moving freely to electrical faults within the switch mechanism. 

Symptoms of a bad Float Assembly include:

• Water overflowing from the washing machine
• Inadequate water levels that affect the washing cycle's effectiveness
• The washing machine failing to start the fill cycle due to a malfunctioning float switch

This OEM LG part is also compatible with some Kenmore models.

This base bracket mounts to the washer's lower frame to hold associated components securely in place. By keeping parts properly anchored, it helps maintain alignment and stability during operation to minimize vibration and noise.

• Attaches to the washer base and provides a mounting point for designated hardware
• Helps keep assemblies from shifting during agitation and spin
• Supports smooth, quieter operation by reducing vibration and rattling
• Common signs of failure include a bent or cracked bracket, loose/misaligned parts, or unusual noises from the base area

• Disconnect power and water supply before servicing; move the appliance for safe access
• Carefully tip or lay the washer back on protective padding; use a helper for stability
• Note the bracket's orientation and reuse existing mounting hardware as applicable
• Tighten fasteners securely and verify nearby parts have proper clearance before test run

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Fabric Softener Cap is an OEM replacement part for LG front-loading washing machines. It is a replaceable component that securely fastens into the internal dispenser drawer, containing liquid fabric softener added during wash cycles. Color: blue. It measures about 2-1/2 inches wide by 4-1/2 inches deep.

Symptoms of a problematic cap could include: 

• Softener stains or residue accumulating around base gasket seals  
• Drips or puddles indicative of compromised sealing surfaces
• Cracks, fatigue, or warping affecting secure closure 

Causes typically relate to normal plastic material breakdown after years of opening and closing cycles. Exposure to cleaning detergents could potentially deteriorate gaskets as well.

Compatible brands include Kenmore Elite and some Café laundry appliances too. 

The Bleach Funnel is an OEM part for LG washing machines. This part safely dispenses and introduces liquid bleach or other cleaning agents into the wash cycle at the appropriate time.

Causes of a bad Bleach Funnel can include physical damage, wear and tear over time, or clogs from residue buildup. 

Symptoms of a faulty Bleach Funnel include:

• Bleach or cleaning agents not being properly dispensed
• Leaks or residue buildup in the dispenser area
• Clogging or blockages preventing proper flow
• Washing machine not effectively utilizing bleach or cleaning additives

This OEM LG part is also compatible with some Kenmore models.

The Detergent Box Assembly is an OEM replacement part for LG washing machines. This assembly is responsible for holding and dispensing detergent and other laundry additives during the wash cycle. It ensures that the correct amounts of detergent, bleach, and fabric softener are released at the appropriate times, contributing to effective cleaning and care of your clothes.

Over time, the detergent box assembly can become worn out or damaged due to continuous exposure to water and detergent. Buildup of detergent residues can clog the compartments, and the mechanical parts of the assembly can also degrade. 

Symptoms of a bad detergent box assembly include:

• The detergent, bleach, or fabric softener not dispensing properly
• Visible cracks, warping, or damage to the box
• Residues remaining in the compartments after a wash cycle
• Leaks from the detergent box area
• Error messages related to dispensing issues

This OEM LG part is also compatible with some Sears/Kenmore washing machine models.

The Dispenser Assembly is an OEM part for LG front-loading washers. It is responsible for dispensing detergent and fabric softener at the appropriate times during the wash cycle. The dispenser assembly contains separate compartments for detergent and fabric softener, as well as timed mechanisms that release each additive when needed for cleaning and softening results.

Causes of a bad dispenser assembly can include issues with the dispensing mechanisms like clogging, jamming, or malfunctions preventing the timely release of detergent and softener. Damage to compartment seals or lids could also cause improper dispensing.

Symptoms of a bad dispenser assembly include:

• Residue or buildup of detergent in the drum or tub
• Strong detergent or fabric softener odors that won't come out of clothes
• Dispenser drawers, lids, or seals that do not close or lock securely

This OEM LG part is also compatible with Sears/Kenmore.

This drain hose cap seals and secures the refrigerator defrost drain outlet so meltwater is directed into the drain hose instead of pooling in the cabinet. Replaces a worn or damaged cap to help stop interior leaks and water buildup. What it does:

• Seals the defrost drain outlet to prevent water from spilling into drawers or onto shelves.
• Guides defrost/meltwater into the drain hose and toward the drain pan.
• Helps reduce odors and pests entering through an open drain opening.
• Fits onto the drain outlet to replace cracked, missing, or loose caps.

• Disconnect power before working inside the refrigerator to avoid electrical hazard.
• Remove shelves and drawers as needed to access the drain outlet; clear any visible debris or ice first.
• Press the cap firmly onto the drain outlet/hose until fully seated; avoid excessive force or prying tools.
• After installation, pour a small amount of warm water down the drain to confirm proper flow and seating.

This cap cover is a small trim piece that protects and hides a fastener or mounting point, restoring the appliance's finished appearance and helping keep dirt and moisture out of the exposed area. What it does

• Covers and protects an exposed screw, bolt or mounting hole to prevent dirt buildup and corrosion.
• Restores a clean, finished appearance to the control panel or housing.
• Helps keep moisture and debris away from the underlying component.
• Useful when original cap is cracked, missing or cosmetically worn.

• Disconnect power to the appliance before attempting any service.
• Typically snaps or presses into place; use a plastic pry tool to avoid scratching surrounding surfaces.
• Replace if cracked or deformed to ensure a secure fit.

The Dispenser Hose is an OEM part for LG washing machines. It connects the detergent dispenser to the washer tub, allowing detergent and other cleaning agents to be delivered effectively during the wash cycle.

Causes of a bad dispenser hose can include regular wear and tear, damage from harsh detergents, or physical damage due to kinks, pinches, or impact. Over time, the hose can become brittle, cracked, or clogged, affecting its ability to function properly.

Symptoms of a bad dispenser hose include:

• Leaks or drips from the hose area
• Detergent not dispensing correctly or at all
• Water pooling around the washer
• Visible cracks or splits in the hose

This OEM LG part is also compatible with Sears/Kenmore models.

The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.

Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.

Symptoms of a bad vent hose include:

• Excessive moisture or condensation inside the washer
• Musty odors from the washing machine
• Visible cracks or holes in the hose
• Poor ventilation leading to inefficient washing cycles

This OEM LG part is also compatible with Sears/Kenmore.

Includes sensor probe

The Dispenser Inlet Hose is an OEM part for LG washing machines. This hose directs water from the water inlet valve to the detergent dispenser, ensuring that water mixes with the detergent before entering the drum for efficient washing. The hose is designed to withstand high water pressure and temperature fluctuations.

Over time, the dispenser inlet hose can become clogged, cracked, or worn out due to regular use. Causes of a bad inlet hose include mineral deposits or debris buildup, wear and tear, and exposure to high temperatures or pressure that can cause the hose to degrade.

Symptoms of a bad dispenser inlet hose include:

• Leaking water around the detergent dispenser area
• Reduced water flow into the dispenser
• Visible cracks or wear on the hose
• Incomplete dissolution of detergent during wash cycles

This OEM LG part is also compatible with Sears/Kenmore.

The Dispenser Inlet Hose is an OEM part for LG washing machines. This hose directs water from the water inlet valve to the detergent dispenser, ensuring that water mixes with the detergent before entering the drum for efficient washing. The hose is designed to withstand high water pressure and temperature fluctuations.

Over time, the dispenser inlet hose can become clogged, cracked, or worn out due to regular use. Causes of a bad inlet hose include mineral deposits or debris buildup, wear and tear, and exposure to high temperatures or pressure that can cause the hose to degrade.

Symptoms of a bad dispenser inlet hose include:

• Leaking water around the detergent dispenser area
• Reduced water flow into the dispenser
• Visible cracks or wear on the hose
• Incomplete dissolution of detergent during wash cycles

This OEM LG part is also compatible with Sears/Kenmore.

The Inlet Hose is an OEM part for LG washing machines. It connects the water supply to the dispenser drawer, enabling the precise delivery of water to distribute detergent, fabric softener, and bleach during the wash cycle. This hose plays a key role in ensuring that cleaning agents are effectively mixed with incoming water, optimizing wash performance.

Causes of a bad Inlet Hose can include blockages due to sediment build-up, wear and tear from regular use, or damage during installation or maintenance, leading to improper functioning.

Symptoms of a bad Inlet Hose include:

• Inconsistent water flow to the dispenser
• Leaks during the fill stage of the wash cycle
• Detergent residue left in the dispenser drawer
• Issues with the washing machine's ability to start the wash cycle properly

This OEM LG part is also compatible with Sears/Kenmore.

This inlet hose carries water into the washer's fill system during wash and rinse cycles. Replacing a cracked or leaking hose restores proper filling and helps prevent water around the appliance from seepage at the connections.

• Routes incoming water to the washer's fill path during the fill cycle
• Helps maintain a watertight connection between the supply and the machine
• Replace if you see cracks, bulges, kinks, or active leaks
• Helps resolve water on the floor during fill, intermittent fill errors, or slow/no fill due to restricted flow

• Unplug the washer and turn off the water supply valves before starting
• Place a towel or pan to catch residual water and relieve line pressure
• Note hose routing/orientation; install the new hose without kinks and hand-tighten fittings
• Restore water and power, then check all connections for leaks during a short fill test

This replacement connector hose routes water between the refrigerator water valve and the dispenser or ice maker, restoring reliable water flow and helping prevent leaks. It's a direct-fit service part used where the factory hose is worn or damaged. What it does

• Connects the refrigerator water valve to the dispenser or ice maker, providing a sealed water path.
• Restores proper water and ice delivery when a cracked or leaking hose causes reduced flow or pooling.
• Helps prevent leaks by replacing brittle, cracked, or split tubing and fittings.
• Works with the original fittings and routing used by the manufacturer for a secure connection.

• One replacement connector hose.

• Turn off and disconnect the refrigerator's water supply and power before starting.
• Verify orientation and routing match the original hose; avoid sharp bends or kinks.
• Tighten fittings securely but avoid over-tightening; inspect for leaks after reconnecting water.

The Drain Hose is an OEM part for LG washing machines. It is designed to carry used water from the washing machine to the household drain. This hose ensures that water is efficiently expelled from the washer, preventing any overflow or leakage issues.

Causes of a bad drain hose can include cracks or splits due to wear and tear, clogs from debris or residue buildup, and damage from mishandling or improper installation. Such issues can compromise the hose's ability to transport water effectively.

Symptoms of a bad Drain Hose include:

• Water leaks during or after the wash cycle
• The washer not draining properly
• Visible cracks or damage to the hose
• Unpleasant odors due to trapped debris or standing water

This OEM LG part is also compatible with Sears/Kenmore models.

This DC pump motor assembly drives the appliance pump to move and remove water during drain and circulation cycles. It restores pump operation so the washer/dishwasher can empty properly and avoid standing water. What it does:

• Powers the drain/recirculation pump to move water out of the tub during drain and wash cycles.
• Common repair when the appliance fails to drain, leaves standing water, or shows drain-related errors.
• Helps restore normal water flow for wash, rinse and drain sequences.

• Disconnect power (and water, if applicable) before servicing the appliance.
• Inspect hoses, filters and the pump housing for clogs before replacing the motor.
• Note connector orientation and mounting location; transfer gaskets/seals if the original must be reused.

The Pump Filter Assembly is an OEM replacement part for LG washing machines. It is a crucial component that filters out lint, debris, and other particles from the wash water, preventing them from recirculating and damaging the pump or other internal components.

Symptoms of a need to replace the pump filter assembly:

• Clogging or blockages, leading to poor drainage or water not draining completely
• Excessive buildup of lint, hair, or other debris in the filter screen
• Leaks or water seeping from the filter housing or surrounding area
•  Unusual noises or vibrations during the drain or spin cycles, indicating a potential blockage

Causes of a faulty pump filter assembly can include excessive lint accumulation, damage to the filter screen or housing due to impact or mishandling, and general wear and tear over time.

This OEM LG part is also compatible with Sears/Kenmore washing machines.

The Stator Assembly is an OEM replacement part for LG washing machines. It is an electrical component inside the motor that converts rotational motion to electrical energy to power spinning motions.  Note: For the RPS or Hall Sensor, order part number AP7015078.

Symptoms of a faulty stator include:

• Slow or inefficient spinning, rubbing noises  
• The machine failing to fully drain or spin clothes
• Repeated blowouts or failure of related motor components

Causes can be wear and tear over extended use. Environmental factors like dust and moisture exposure may degrade insulation integrity. 

This OEM stator is also compatible with some Kenmore front-load washer models.

This hose connector joins the water inlet hose to the appliance, restoring a secure, watertight feed for normal fill and wash cycles. Replaces a worn or damaged connection to stop leaks and ensure proper water flow. What it does:

• Connects the incoming water hose to the appliance inlet for stable water delivery
• Stops leaks caused by cracked, split, or loose connector fittings
• Helps restore normal fill behavior when a failed connector is preventing proper water flow
• Serves as a direct replacement for a damaged or corroded inlet connection

• Turn off and shut off the home's water supply and unplug the appliance before installing
• Remove the old connector and clean mating surfaces; inspect hose and clamps for wear
• Hand-start fasteners, then snug fittings—avoid over-tightening to prevent damage

This is the direct-drive rotor for the dishwasher wash motor. It pairs with the stator to spin the impeller and circulate wash water through the spray arms, helping restore proper spray pressure and quieter operation when the original rotor is worn.

• Couples with the stator to drive the circulation pump impeller
• Moves wash water through the spray arms for consistent cleaning performance
• Common failure signs: little or no spray, poor cleaning, loud humming or grinding from the pump area, or intermittent wash action
• Physical damage or weakened magnets can prevent proper rotation

• Disconnect power and water supply and pull the unit forward for access
• Remove the toe-kick and drain remaining water at the sump
• Remove the pump cover and center fastener, then pull the old rotor straight off
• Seat the new rotor fully, reassemble, and run a test cycle to check operation and leaks

This hose connector joins the water inlet hose to the appliance, restoring a secure, watertight feed for normal fill and wash cycles. Replaces a worn or damaged connection to stop leaks and ensure proper water flow. What it does:

• Connects the incoming water hose to the appliance inlet for stable water delivery
• Stops leaks caused by cracked, split, or loose connector fittings
• Helps restore normal fill behavior when a failed connector is preventing proper water flow
• Serves as a direct replacement for a damaged or corroded inlet connection

• Turn off and shut off the home's water supply and unplug the appliance before installing
• Remove the old connector and clean mating surfaces; inspect hose and clamps for wear
• Hand-start fasteners, then snug fittings—avoid over-tightening to prevent damage

This water level pressure switch senses the washer tub's water level and signals the control to start or stop filling. It restores accurate fill detection for proper wash cycles and helps prevent overfilling or improper operation. What it does:

• Detects water level via a vacuum hose and tells the control board when to stop filling
• Helps prevent overfill, underfill, and related cycle interruptions
• Can resolve symptoms like washer not filling, overfilling, or stopping mid-cycle
• Works as the sensing interface between the tub and the control system

• One water level pressure switch assembly

• Disconnect power and shut off water supply before replacing the part
• Note the vacuum hose routing and electrical connector locations before removal
• Handle the small vacuum hose and plastic fittings gently to avoid damage or air leaks

The Suspension Spring is an OEM part for LG washing machines, specifically designed to support the tub assembly and maintain its stability during the wash and spin cycles. This spring plays a critical role in absorbing vibrations and reducing the amount of movement transferred to the washing machine's frame, ensuring smooth and quiet operation. 

Causes for a Suspension Spring to fail include normal wear and tear from repeated use, overloading the washing machine beyond its capacity, which can stretch or stress the springs, and corrosion from exposure to moisture and laundry detergents. 

Symptoms of a bad Suspension Spring include:

• Increased vibration and noise during the spin cycle.
• The washing machine "walking" or moving from its original position.
• Uneven drum movement, leading to inconsistent washing and spinning.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Suspension Spring Holder is an OEM part for LG washing machines. This holder supports the suspension springs that help stabilize the washer drum during operation, reducing vibration and movement. It plays a critical role in ensuring smooth and quiet operation of the washing machine.

Over time, the suspension spring holder can become worn or damaged due to regular use, heavy loads, or accidental impacts. Causes of a bad suspension spring holder include wear and tear, physical damage, or corrosion from moisture exposure.

Symptoms of a bad suspension spring holder include:

• Excessive vibration or shaking during wash cycles
• Unusual noises, such as banging or clunking
• The washer drum appearing misaligned or sagging
• The washing machine moving or walking during operation

This OEM LG part is also compatible with Sears/Kenmore.

This power cord assembly restores a secure electrical connection to your appliance so it can safely receive power. It replaces a worn, damaged, or faulty cord to help prevent interruptions and poor contact during normal use. What it does:

• Re-establishes the appliance's main power connection for reliable operation
• Replaces frayed, burnt, or damaged cord insulation and terminals
• Can stop intermittent power loss, sparking, or poor contact at the cord connection
• Provides the correct OEM-fit electrical cord and connector interface

• Always disconnect power at the breaker or unplug the appliance before starting work.
• Tighten terminal screws securely and avoid pinching or kinking the cord.

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

This hose clamp secures a rubber hose connection to prevent leaks where the hose meets its fitting. A tight, uniform seal helps maintain proper water flow and keeps the appliance operating reliably.

• Provides a tight, 360-degree seal around the hose barb/fitting
• Helps correct issues like water leaks at the hose connection point
• Maintains correct hose attachment during operation and vibration
• Step-less ear design distributes clamping force evenly

• Unplug power and shut off water supply before servicing
• Note clamp orientation and hose routing before removal
• Use appropriate ear-clamp pincers or pliers to compress the clamp evenly
• Check the hose and fitting for wear; replace if cracked or deformed

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

This hose clamp secures a washer hose to its fitting to maintain a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop seepage at hose joints and keep the washer operating reliably.

• Holds the hose firmly on pump, tub, or drain fittings to help prevent leaks
• Maintains clamping pressure during operation and vibration
• Replace if rusted, bent, cracked, or no longer holding tension
• Typical symptoms: water dripping at hose connections or a hose that slips off

• Disconnect power and shut off water; drain any remaining water from the unit
• Release and slide back the old clamp, then remove the hose
• Fully seat the hose on the fitting and position the clamp just behind the hose bead/ridge
• Secure the clamp and run a brief test to check for leaks

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This connector nozzle is the small replacement plumbing piece that directs water between internal components, restoring proper spray and flow where a worn or damaged nozzle causes leaks or weak/erratic water delivery. What it does

• Channels water from the supply path to the spray/nozzle outlet to maintain correct flow
• Keeps seals and adjoining fittings aligned to prevent leaks
• Replaces cracked, clogged, or broken nozzle pieces that cause weak spray or misdirected water
• Helps stop dripping or continuous flow caused by damaged connector ends

• Connector nozzle

• Disconnect power and water supply before attempting repair
• Handle carefully to avoid damage to mating surfaces and seals; replace any worn gaskets
• Basic hand tools typically required; follow your appliance's service manual for disassembly and torque guidance

This washer clutch assembly engages the drive system to shift between wash and spin modes. Replacing a worn clutch restores smooth agitation and full-speed spin performance, reducing noise and leaving clothes properly wrung out at cycle end.

• Engages and disengages the drive to transition between wash/agitate and spin
• Transfers motor torque to the basket during wash and spin
• Worn clutch can cause weak or no spin
• May result in no agitation or intermittent shifting
• Can cause grinding/scraping noises and leave clothes wet after the final spin

• Unplug the appliance and shut off water before starting
• Access from the bottom; support the washer securely to prevent tipping
• Remove obstructing drive components to reach the clutch; note hardware/wire routing for reassembly
• After installation, rotate the basket by hand and run a quick test cycle to confirm proper operation

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

The Tub to Pump Hose is an OEM replacement part for LG top-load washing machines. This hose safely transports water between the wash tub and drain pump. The hose measures 13 inches in length.

Causes of failure relate to constant flexing under water pressure strains that accumulate over years of usage. Excess minerals in hard water areas promote accelerated breakdown of flexible PVC material.

Symptoms of a cracked or leaking tub to pump hose include: 

• Water not draining or taking an abnormally long time
• Water continually accumulating inside the machine cabinet   
• Error codes related to drainage issues displayed  
• Puddles forming near or under the back of the washer

This genuine LG hose is also compatible with select Sears/Kenmore units as well.

The Inner Door Boot Seal Clamp is an OEM part for LG washing machines. The clamp's primary function is to secure the door boot seal in place, preventing leaks during the wash cycle. 

Causes of a bad Inner Door Boot Seal Clamp can include corrosion due to exposure to moisture and detergent, loss of tension over time, or physical damage which can lead to a compromised seal.

Symptoms of a bad Inner Door Boot Seal Clamp include:

• Water leaking from the front of the washing machine
• Visible rust or damage on the clamp
• The door boot seal coming loose or falling off

This genuine LG OEM replacement part is also compatible with some Kenmore models. 

The Air Chamber is an OEM part for LG washing machines. This part connects to the pressure switch and ensures the washer machine fills with the correct amount of water for the selected cycle. 

Causes of a bad  Air Chamber can include clogging due to detergent residue or debris, cracks or perforations that lead to air leaks, and aging of the material, which might compromise its integrity and function.

Symptoms of a faulty Air Chamber include:

• Inaccurate water level readings leading to overfilling or insufficient water during cycles
• Unusual noises during the fill cycle, indicating air escaping
• The washing machine failing to start the wash cycle due to improper water level detection
• Error codes displayed on the machine that relate to water level issues

This OEM LG part is also compatible with some Kenmore models.

The Hose is an OEM part for LG washing machines. This component is crucial for the proper flow of water into and out of the washing machine, ensuring efficient washing and rinsing cycles. The hose is designed to withstand high water pressure and regular use.

Causes of a bad hose can include wear and tear over time, exposure to harsh water conditions, or accidental damage such as kinks or punctures. Ensuring the hose is in good condition is essential to prevent leaks and maintain optimal water flow.

Symptoms of a bad hose include:

• Water leaks around the hose connections
• Reduced water flow into or out of the washing machine
• Visible cracks, bulges, or kinks in the hose

This OEM LG part is also compatible with Sears/Kenmore.

This hose connector joins two internal water lines inside your washer to create a secure, leak-resistant connection. Replacing a worn coupler helps stop drips and keeps water moving properly during fill, wash/recirculation, and drain cycles.

• Joins two hoses inside the appliance for a tight, reliable seal
• Helps maintain proper water flow during operation
• Replace if cracked, deformed, or if hoses slip off despite clamp tension

• Unplug the washer and turn off water supply; expect some residual water
• Access the hose junction and note hose routing and clamp positions
• Fully seat hoses onto the connector and secure clamps behind the hose bead
• Reassemble and run a short test cycle while checking for leaks

The Washing Machine Shock Absorber Kit is an OEM part for LG washing machines. This kit includes a shock absorber designed to reduce vibrations and absorb shocks during the wash cycle, providing stability and minimizing excessive movement. 

Over time, the shock absorbers can wear out due to regular use, exposure to heavy or unbalanced loads, or damage from impact. These factors can lead to reduced effectiveness of the shock absorbers, causing increased vibrations and noise.

Symptoms of a bad shock absorber kit include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or thumping noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

This OEM LG part is also compatible with Sears/Kenmore.

The Hinge Pin is an OEM part for LG washing machines. It serves as a pivot point for the washer door, allowing it to open and close smoothly. This component is crucial for maintaining the proper alignment and function of the washer door, ensuring a secure and reliable seal during operation.

Common causes of a bad hinge pin include frequent use leading to wear and tear, physical damage from accidental impacts, or rust and corrosion over time. A compromised hinge pin can result in misalignment of the door, affecting the washing machine's ability to close properly and maintain an effective seal.

Symptoms of a bad hinge pin include:

• Difficulty opening or closing the washer door
• Door not staying securely closed during operation
• Squeaking or grinding noises when the door is moved
• Visible wear or damage to the hinge pin

This OEM LG part is also compatible with Sears/Kenmore models.

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.