Parts for Lg WM3485HWA: Cabinet / Control Panel Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This Leg Adjusting Wrench is a simple tool used to turn and secure appliance leveling legs so washers and dryers sit flat and operate quietly. It makes adjusting legs faster and helps reduce rocking and vibration. What it does:

• Fits over standard appliance leveling legs to raise or lower each corner
• Helps stabilize machines to prevent rocking and uneven operation
• Reduces vibration and noise caused by unlevel appliances
• Useful when installing, moving, or re-leveling washers and dryers

• Turn legs slowly and adjust one corner at a time until the appliance sits level.
• Unplug the appliance (and shut off gas supply for gas dryers) before performing major moves or checks.
• Use caution to avoid pinching fingers when lowering legs; keep hands clear of pinch points.
• Check for damaged feet or mounting hardware and replace as needed.

Washer manual holder that secures care guide documentation to your appliance. Replace if cracked, broken, or missing to keep owner's manual accessible.

These non-skid pads attach to the bottom of the washer's leveling legs to prevent the machine from sliding or walking across the floor during operation. They are made of durable rubber or similar grip material. Replace them if your washer vibrates excessively, moves out of position during spin cycles, or if the existing pads are worn, cracked, or missing.

Excessive noise or debris inside your washer? This rear cover panel shields internal components and maintains airflow. Straightforward DIY fix.

Drum bearing bushing for washers. Installs between drum and bearing assembly. Replace if cracked, worn, or missing to restore proper drum support.

Secures internal washer components and maintains proper alignment. Replace when brackets are worn, broken, or causing rattling. Confirm fit with your model number.

Shipping bolt assembly secures the washer drum during transport. Replace if bolts are lost, damaged, or missing before moving your washer to prevent damage.

Secures washer drum during moving or transport. Immobilizes internal components to prevent damage. Replace if missing, lost, or needed for relocation.

Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.

What it does

• Locks the tub and basket to limit movement in transit
• Helps prevent suspension damage and internal rattles while relocating
• Replaces missing, bent, or stripped transport bolts
• Useful for moves, storage, or service shipments

What’s included
One shipping bolt assembly (sold individually).

Install notes

• Unplug power and turn off water before service
• Insert through the rear panel into the designated mounting point; tighten snugly—don’t overtighten
• Do not operate the washer with shipping bolts installed; remove all bolts after placement
• Some models use multiple bolts and lengths—match count/positions to your owner’s manual

Usage tip
After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.

This lifter assembly moves clothes through the washer drum during the wash cycle, ensuring proper agitation and cleaning. It fixes issues with clothes tangling, poor washing results, or loud banging noises during operation.

Mounts the door hinge to your washer's front cabinet. Replace if bracket is bent, broken, or missing to restore proper door alignment and sealing.

This metal assembly connects your washer's inner tub to the transmission and supports the tub during the spin cycle. It transfers the spinning motion while handling the forces created during high-speed operation. Replace this spider if your washer makes loud banging noises, won't spin, or if the tub moves excessively.

Replacement bolt that secures the spider assembly to the inner wash basket. Needed when hardware is missing, stripped, or corroded during repairs.

Replace your washer's wire harness assembly if wires are frayed, connectors are damaged, or the harness is broken. Installs inside the control panel area.

Supports the drum for smooth, quiet spinning. Replace when you hear grinding or loud noises during cycles. Verify fit with your model number.

Supports the inner drum for smooth rotation during wash and spin cycles. Replace when you hear grinding, loud noise, or excessive vibration. Confirm fit with your model number.

Washer won't spin or makes grinding noises? The motor rotor bolt secures the rotor to the motor shaft. Requires a 17mm socket for installation.

Seals the rear tub to prevent water leaks during wash and spin cycles. Replace if you notice leaking or bearing noise. Confirm fit with your model.

Outer trim panel that covers and finishes the washer cabinet area. Replace if cracked, dented, or missing to restore appearance and protect components.

This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.

• Secures panels, brackets, and mounting points as specified by the manufacturer
• Replaces screws that are lost, damaged, corroded, or stripped
• Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
• Maintains proper alignment and stability of the assembly

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to its original location; start threads by hand to avoid cross-threading
• Use the correct driver; tighten snugly without over-torquing into metal or plastic
• Refer to your model's parts diagram to correct location and quantity

Secures the outer door boot seal to prevent water leaks. Replace if damaged, rusted, or losing tension. Includes tensioning spring. Verify fit.

Door hinge assembly for washer machines. Mounts the door to the frame and allows smooth opening and closing. Replace when hinge is cracked or worn.

Washer won't spin or shows LE error? A faulty motor wire harness disrupts power to the drum motor. DIY fix in 20-60 minutes with basic hand tools.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

The Washer Gasket is an OEM replacement part for LG washing machines. It is a flexible seal that lines the opening of the washer tub, creating an airtight barrier to prevent water leaks and ensure proper containment during the wash and spin cycles.

Symptoms of a bad washer gasket include:

• Water leaking from the front of the washing machine
• Excessive moisture or condensation buildup around the gasket area
• Difficulty in properly closing and latching the washer door due to a worn or damaged gasket

Causes of a washer gasket failure can range from general wear and tear over time, to physical damage from being pinched or cracked, to improper installation or alignment issues.

This OEM LG part is also compatible with Sears/Kenmore models.

Washer screw

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

Motor harness wiring for washers. Connects motor to control board. Replace if wires are damaged, frayed, connectors broken, or harness is worn out.

Complete washer door assembly restores proper sealing and appearance. Replace when door is damaged, dented, or cracked. Confirm fit with your model number.

Washer not starting, won't spin, or showing error codes? This sensor assembly detects operating conditions and restores proper control signals. Direct fit.

Washer outer door frame that surrounds the door opening. Replace this cosmetic part if your current frame is cracked, broken, or damaged.

Replacement door handle for front-load washers. Installs on the outer door panel for opening and closing. Order if your handle is cracked or broken.

Fix DE door error codes or doors that won't latch with this washer door latch hook. Simple 15-minute DIY repair with video guide. Secures door during cycles.

Replace your broken or cracked laundry center door handle. This exterior handle installs on the front panel for opening and closing the door.

Fix slow filling, no-fill, or continuous filling issues by replacing a faulty water inlet valve. Straightforward 15-20 minute repair for most DIYers.

Fix washer IE error or no water flow issues with this water inlet valve. Controls hot or cold water flow into wash drum. 15-minute DIY repair.

Cabinet base assembly for washers. Supports and encloses internal components at the bottom of the unit. Replace if cracked, rusted, or damaged.

Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.

Replacement knob assembly that restores control and precise selection of settings on your appliance. Fits the original control shaft and provides a secure grip for adjusting temperature, cycle, or power settings. What it does

• Restores user control when the original knob is cracked, melted, stripped, loose, or missing.
• Provides a clear indicator/pointer for accurate selection of settings.
• Matches original fit and function to prevent slipping or uneven engagement with the control shaft.
• Helps resolve symptoms like a knob that won't turn, slips on the shaft, or has a broken pointer.

• Always disconnect power to the appliance before servicing; shut off gas supply for gas ranges.
• Typically installs without tools—remove the old knob by pulling it straight off, then press the new knob onto the control shaft.

Replaces a worn, cracked, or damaged washer drawer front panel. Restores appearance and ensures proper drawer operation. Includes mounting surface for handle.

Replace a broken, rusted, or missing leveling leg assembly. Installs at the base to stabilize your washer, reduce vibration, and adjust height.

Fix a loose or missing fabric softener cap that won't stay in place or causes drawer issues. Simple snap-in replacement restores proper dispensing.

Bleach dispenser funnel for LG front load washers. Installs in detergent drawer to safely dispense bleach. Replace if cracked, broken, or missing.

Fix detergent not dispensing or a broken dispenser drawer. This washer detergent box assembly holds and releases soap properly. DIY-friendly repair.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This rubber fill hose connects the household hot water supply valve to the washing machine's water inlet valve. It delivers hot water into the wash tub during the fill cycle. Replace this hose if it is cracked, leaking, bulging, or showing signs of deterioration to prevent water damage.

Fix leaks or poor water flow with a new washer inlet hose. This part channels household water supply into your machine for proper filling and operation.

Outer housing case for washers. Protects internal components and provides external structure. Replace if cracked, damaged, or worn for proper coverage.

Fix detergent not dispensing or leaking from drawer. This dispenser assembly includes compartments for detergent, bleach, and softener. 15-minute DIY repair.

This part may be black or gray in color.

Replacement cover cap for washers. Conceals exposed screw heads and fastener holes for a clean finish. Install when original cap is cracked or missing.

Connects detergent dispenser to washer tub. Replace if cracked, leaking, or clogged with detergent buildup. Verify fit with your model number.

The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.

Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.

Symptoms of a bad vent hose include:

• Excessive moisture or condensation inside the washer
• Musty odors from the washing machine
• Visible cracks or holes in the hose
• Poor ventilation leading to inefficient washing cycles

This OEM LG part is also compatible with Sears/Kenmore.

Includes sensor probe

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

Joins your washer's water line to internal plumbing with a secure, leak-resistant connection. Replace this connector if cracked, worn, or leaking.

Washer won't drain or shows OE error? This drain pump assembly removes water during spin cycle. Moderate DIY repair with video guide available.

Note: Per the manufacturer, the design changed  of this washer drain pump changed in April 2025. The new gray casing with different fins will still work, as the fins allow access for wiring.

Drain hose carries used water from washer to household drain. Replace if cracked, leaking, deteriorated, or damaged to prevent water overflow issues.

Does not come with a hose or filter. These have to be purchased separately

Routes water from household supply to washer fill valve. Replace this hose if cracked, leaking, worn, or damaged to restore secure water connection.

The PUMP MOTOR is an OEM part for LG washing machines. It is an electric motor that powers the pump responsible for circulating water inside the washing machine tub and through hoses during all wash cycles. Efficient water flow is necessary for proper cleaning and rinsing performance.

Causes of a bad pump motor can include mineral buildup inhibiting smooth rotation, worn motor windings affecting current flow, or damage from water damage into the motor housing.

Symptoms of a bad pump motor include:

• Incomplete or failed wash cycles  
• Inability to fill or drain properly
• Strange noises emanating from the pump area
• Leaks or water issues related to poor water circulation

This OEM LG part is also compatible with Sears/Kenmore.

Water leaking from filter area or drain error? This washer pump filter traps lint and debris. Easy DIY fix with video guide—most install in minutes.

The Damper is an OEM replacement part for LG washing machines. It plays an important role in regulating airflow through the machine's drying system. The damper uses adjustable louvers to direct warm air emitted during the drying cycle. 

Causes of a faulty washer damper include broken internal mechanisms preventing louver movement, and restricting optimal air dispersion. Dust or mineral buildup can also impact function over time.

Symptoms of a problematic damper are

• incomplete or lengthy drying cycles.
• Clothing may still feel damp even after an extended run
• Excessive lint accumulation could also point to improper air management

This OEM LG part is also compatible with Sears/Kenmore.

Mounting bolt for washers. Secures internal components and assembly parts. Replace if bolt is stripped, corroded, missing, or damaged during repairs.

Washer won't spin or turns inconsistently? The stator assembly creates the magnetic field that drives the drum. Moderate DIY repair, 30-60 minutes.

Fix LE error codes and spinning problems with this washer rotor position sensor. Resolves machines that won't spin or make loud noises. Easy 5-10 minute fix.

Fix LE error codes or grinding noises during spin with this washer rotor assembly. Pairs with stator to drive drum rotation. DIY repair in 30 minutes.

Structural frame assembly for washers. Replaces cracked, damaged, or worn cabinet frames. Essential for maintaining washer stability and structure.

Suspension spring supports and stabilizes the washer tub during wash and spin cycles. Replace if broken, snapped, or stretched to restore proper operation.

Washer not filling or overfilling? This water level pressure switch monitors water levels and signals when to stop filling. Easy 10-minute DIY repair.

Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.

Appliance won't power on? This power cord assembly restores electrical connection when the cord is damaged or has poor contact. Direct plug-in repair.

Flexible drain hose assembly that carries wastewater from your washer to the household drain. Replace if cracked, leaking, or damaged during installation.

Pivot hanger assembly that supports and stabilizes washer components. Replace if worn, damaged, or causing misalignment to restore smooth movement.

Fix DE error codes and door lock failures with this washer door lock switch. Most DIYers complete this repair in under an hour with our video guide.

Secures rubber hoses to fittings with constant spring tension to prevent leaks. Replace when rusted or weakened to maintain a tight seal. Confirm fit.

Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.

Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.

Fix washer leaks with this hose clamp. Secures hoses to pumps and valves, preventing water leaks and disconnections during wash cycles. Simple repair.

The Noise Filter Assembly is an OEM part for LG washing machines, designed to minimize electrical noise interference within the appliance. This essential component ensures that the washer operates smoothly without emitting disruptive sounds that can affect both the performance of the washer and the comfort of your home environment. 

Causes of a bad Noise Filter Assembly can range from wear and tear over time to exposure to power surges or electrical spikes, which can damage the internal components of the filter. 

Symptoms of a bad Noise Filter Assembly include:

• Increased electrical noise or buzzing sounds emanating from the washer
• Intermittent disruptions in the washer's performance
• The washing machine failing to start or experiencing power fluctuations

This OEM LG part is also compatible with some Kenmore models.

Prevents water leaks around your washer door during wash and spin cycles. Replace if you notice leaking, cracking, or mold buildup. Verify fit with your model.

Connects water hose to washer nozzle/dispenser assembly. Replace if cracked, worn, or leaking to restore a tight, leak-resistant seal during fill cycles.

Restores interior drum lighting for better visibility when loading and unloading laundry. Replace when light fails or dims to clearly see items in tub.

Replacement tub to pump hose for washers. Transports water from the wash tub to the drain pump. Replace if cracked, split, leaking, or damaged from wear.

Secures the door boot seal to prevent leaks during wash cycles. Replace if corroded, loose, or if water leaks from the door area. Confirm fit with model.

Pressure sensor air chamber for washers. Connects the tub to the water level switch. Replace if cracked, clogged with detergent residue, or leaking air.

Channels household water to your washer's fill system. Replace if cracked, leaking, or worn to restore proper flow and prevent water damage to floors.

Delivers fresh water from your home supply to your washer. Replace if cracked, leaking, worn, or damaged to restore proper fill connection.

Replace your washer's drain hose if cracked, leaking, or damaged. Connects the pump to the standpipe for proper water drainage during wash cycles.

Comes with clamps and adapter.

The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.

Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.

Symptoms of a bad clamp include:

• Water leaking from hose connections
• Hoses coming loose or detaching during operation
• Visible rust or damage on the clamp
• Poor water flow or pressure issues

This OEM LG part is also compatible with Sears/Kenmore models.

Comes with 2 pins.

Locking pin for shock absorber.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.