Cap, Lid & Cover

This is a quality rear engine cover that is used on several types of string trimmers. The component is tightened onto the back of the trimer to offer protection and shielding to the engine. It is made of a durable material and comes with both the cover and four screws to attach it to a string trimmer. Over time, the rear engine cover can become damaged, broken, or lost and should be replaced to ensure the engine is protected.Check the rear engine cover for cracks and other damage before installing a new replacement part. First, remove the screws from the rear engine cover so it can be taken off of the string trimmer. An O-ring may be needed to create the proper clearance when installing the new rear engine cover. Make sure to properly tighten the screws on the cover before use.This rear engine cover is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The engine cover is designed to be compatible with string trimmers manufactured by Bolens, MTD, Yard Machines, Murray, and Craftsman.

This is a head cap that is typically used with a variety of. The head cap is tasked with protecting the line fitting and housing to prevent wear and tear that can be caused if the string trimmer makes contact with the ground. Since the head cap may make contact with the ground or other items, it can become damaged or broken. If these things occur, or the head cap has been lost, it will need to be replaced. If it is not, the line fitting and housing could be damaged and prevent the string trimmer from functioning properly.No tools are required to replace the head cap but work gloves are useful for the process. The original head cap screws on and off so it can be removed easily. After the old component has been taken off, the new head cap can be installed in its place. Before making the repair, the string trimmer should be powered off and the spark plug wire should be disconnected.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as a single component. The head cap is made to be used with string trimmers manufactured by Craftsman and MTD.

This is a genuine replacement air box cover. It fits over the air box housing and helps to prevent dirt and debris from entering, while also preventing the air filter from becoming wet in the case of rain or falling out during use. The air filter is essential for ensuring clean air for combustion within the engine. The air box cover is made of durable plastic. However, over time, plastic components can become brittle with exposure to high heat and harsh sunlight, leading to cracks and damage. The air box cover can also be damaged if the machine is dropped or through contact with hard surfaces. Replacing the air box cover is a simple process. A plastic knob holds the cover to the base. Simply twist and remove the knob, and then remove the damaged air box cover. Replace it with the new cover and put the knob back in place. This replacement air box cover fits several Husqvarna edgers, brush cutters, and trimmers. Note that this is a genuine OEM part and is sold individually.

This quality air filter cover protects and secures the air filter to the chainsaw. If the air filter cover is not in place, the air filter could become excessively dirty or damaged. Through use or impact, the air filter cover can become damaged and may need to be replaced. A quick visual inspection will tell whether there are holes or cracks in the cover that necessitate a replacement.This air filter cover replacement requires no tools. The air filter cover comes with small tabs that can be used to secure it in place over the air filter. Tug on the original air filter cover and pull it out of its place before pressing the new one into place using its plastic tabs. Reassemble any other components before use.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The air filter cover is designed to be used with chainsaws manufactured by Poulan, Poulan Pro, and Craftsman.

This is a replacement oil cap for a variety of small gasoline-powered tools they build. These devices include power saws, chainsaws, trimmers, and pruners. The oil cap is tethered to the oil tank, granting easy access to the engine oil for filling or replacement while preventing outside contaminants from getting into the oil basin and, thus, the crankcase. While the cap is not a moving part, it is one of the most exposed pieces of this work equipment. As such it collides with multiple heavy objects such as other tools, trees, cement structures, and truck beds. This type of wear and tear can cause the interior threads of the cap to warp so that the cap cannot be closed tightly. The cap can also be damaged so that it leaks. For safety reasons as well as for the proper operating condition of the equipment, a damaged oil cap should be replaced immediately. Make sure when removing the old cap that the tether is completely freed from the power tool, and make sure the new tether is properly attached. This replacement cap is a genuine OEM part, built to the same specification as the factory original piece and fits Ryobi and Poulan machines.

This part is a bottom pan. The bottom pan is what covers the moving parts in an engine, including the transmission and gears. The bottom pan is what protects the engine, transmission, and gears from any debris that would impede the operation of the outdoor power equipment if it entered the engine area. This part is black and made from plastic.A new bottom pan may be needed if the current bottom pan is broken, cracked, or damaged in any way. The operator can visually inspect the bottom pan to determine whether the part needs to be replaced. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This is a genuine OEM part sourced directly from Husqvarna. It is sold individually. This bottom pan is compatible with snowblowers manufactured by Husqvarna and Craftsman.

This part is a shield that is used on lawnmowers and lawn tractors. It is manufactured out of a high-quality and durable metal. The purpose of the shield is to protect the engine from any flying debris. This component is held in place by two bolts.A new shield may be needed if the current one is cracked, broken, bent, or damaged in any way. If the shield experiences an impact collision with a hard object, it could become damaged. A socket set may be needed during the replacement of the shield. Make sure the outdoor power equipment machine is cooled off prior to attempting to work on it. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This shield is a genuine Husqvarna part. It is sold individually. This particular shield is compatible with lawnmowers and lawn tractors that are manufactured by Husqvarna.

This is a leaf blower starter cover assembly that is part of the starter system. The part is responsible for keeping the starter pulley sitting on the motor. It protects the pulley and prevents debris from reaching the internal part of the leaf blower. If dirt and dust get into the starter, it can cause damage and create the need for expensive repairs. The starter cover assembly is made of strong components but can experience wear or impacts that cause damage.If the starter cover assembly is damaged or missing, it should be replaced. Turn off the leaf blower and make sure it has had time to cool down. Disconnect the spark plug wire so the leaf blower cannot power on. A screwdriver will be needed to remove the original starter cover assembly from the leaf blower. Save the screws and use them to install the replacement part. Reassemble, replace the spark plug, and use as normal.The starter cover assembly is used in leaf blowers manufactured by Husqvarna and Craftsman. This is an authentic OEM component that is priced on an individual basis. It is directly sourced from the manufacturer.

This is a fuel cap that is used with several types of small engine lawn and garden equipment. The purpose of the fuel cap is to make sure that all gasoline in the fuel tank stays in place and there are no leaks present. The fuel cap can experience wear and tear over time or become cracked, broken, or damaged if it impacts other items. If fuel can be smelled through the cap, if the cap doesn't tighten, or if it is otherwise visibly damaged, the fuel cap should be replaced.Prior to replacement or even removing the fuel cap, the equipment should be placed in a well-ventilated area. It's also important to disconnect the spark plug wire to create a safe environment. Empty any fuel in the tank into an appropriate container before moving on. Once empty, you can replace the old cap with a new one.This is a genuine OEM replacement component that is directly sourced from the manufacturer. It is sold as a single fuel cap. The part is created to be compatible with string trimmers, hedge trimmers, and leaf blowers manufactured by Poulan, Poulan Pro, and Craftsman.

This is a standard fuel cap for a hedge trimmer, chainsaw, or weed eater. The fuel cap assembly goes into the tank then screws onto the top of the fuel tank. A fuel cap keeps dirt and debris from falling into the fuel tank and gunking up the engine, causing it to misfire or corrode. Fuel cap assemblies are made of plastic, so they can dry out and snap. If the rubber seal on the fuel cap assembly is no longer preventing fuel from leaking, it’s time to replace it. Installing a new fuel cap assembly is simple. Just push the stopper in and screw on the lid. This is a genuine OEM product shipped from Husqvarna, the manufacturer of this part. This part is also compatible with Craftsman and Poulan products. Part sold individually.

This replacement part includes one fuel cap assembly and is compatible with specific models of gas-powered blowers and trimmers. This part is made of high-quality plastic. It consists of a black cap that is approximately 2 inches in diameter with a retainer connection to keep the cap from falling on the ground. The cap is meant to cover the fuel tank's fill nozzle. Replacing a lost, leaky, or damaged cap won't require any tools. This original OEM part is designed to deliver a perfect fit for compatible equipment. It is compatible with outdoor power equipment from Craftsman, Husqvarna, Poulan, and Weed Eater. This replacement part is sold individually.

This replacement part is a gear cap. This is a genuine replacement part made by Husqvarna. This part is small but used to keep different gears within the lawnmower safe and secure during use. This part is made of durable plastic and meant to be a strong protector for many gears. A new gear cap might be needed if the current one is missing or damaged in any way. This can include being dented, bent, cracked, or chipped. If the gear cap is not able to stay in place, it might be time to replace it. Be sure to wear work gloves during this repair. It is also recommended that the user refers to the appropriate user manual before replacing this part. This part is sold individually and is sourced directly from the manufacturer. This part is also a genuine OEM replacement part to ensure proper fit and long-lasting use.

This replacement part is a fuel cap assembly. This is a genuine replacement part made by Husqvarna. Fuel caps are commonly found in machines that require fuel to run. The engine then uses the fuel to operate effectively. The tank is what holds the fuel so that it can be accessed during use, and the fuel cap ensures that the substance stays inside the tank and does not escape during use.A new fuel cap assembly might be needed if the current one is damaged or leaking the fuel. If this is the case, replace the cap immediately as leaking fuel is a serious safety hazard. It is recommended that work gloves be worn as there can still be fuel leftover in the tank during the repair. This is a genuine OEM replacement part to ensure long-lasting use. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.

This replacement part is a dust wheel. This is a genuine replacement part made by MTD. This part is used to help prevent wheels from becoming too dusty or dirty when not in use. A new dust wheel might be needed if the current on is missing or damaged. If the dust wheel is torn or unable to close properly, it might be time to replace it. This is a fairy simple repair as the user should be able to slip the dust wheel on over the current wheels. Be sure to purchase the correct amount as these are sold individually. Refer to the user manual for more instructions on how to replace this specific part. This part is sold individually and is sourced directly from the manufacturer. This part is also a genuine OEM replacement part to ensure proper fit.