Cooktop Heating Element

This broil element provides the intense top heat your electric oven needs for broiling and finishing dishes. Replacing a failed element restores consistent top browning when the broiler no longer heats or heats unevenly.

• Heats from the top of the oven cavity during broil to sear and brown foods
• Replaces a burned-out, shorted, or physically damaged element
• Symptoms: broiler won't heat, intermittent heating, uneven top browning, or visible blistering/breaks

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove oven racks; support the element while removing mounting screws and gently pull it forward to access terminals
• Transfer wires one at a time to the new element; ensure tight connections and that terminals do not touch metal surfaces; restore power and test broil

The Surface Element is an OEM replacement part for Whirlpool ranges. It is responsible for generating heat on the cooktop, allowing for efficient and even cooking. This component is designed to provide adjustable heat levels to accommodate various cooking needs, from simmering to boiling.

Symptoms of a bad Surface Element include:

• Inconsistent heating or failure to heat up
• Visible damage or wear, such as burns or warping
• Electrical issues, like sparking or short-circuiting

Causes for a malfunctioning Surface Element can be attributed to electrical failures, prolonged use at high temperatures, or physical damage due to spills and overflows.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Bake Element is an OEM part for GE ranges. This part provides the necessary heat for baking and roasting inside the oven cavity. The bake element is located at the bottom of the oven and generates heat when electrical current passes through it.

Causes of a bad bake element can include general wear and tear from frequent use, damage due to accidental impacts or spills, and electrical issues such as short circuits or power surges.

Symptoms of a bad bake element include:

• The oven not heating up properly or at all
• Uneven baking or roasting results
• Visible damage such as burns, blisters, or breaks in the element
• The oven tripping circuit breakers or fuses

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This bake element is the primary heat source for the bake cycle in your range or wall oven. Replacing a failed element helps restore proper preheating and more even results when using the bake setting.

• Provides direct heat during the bake cycle
• Works with the control/thermostat to reach and maintain set temperature
• Common failure symptoms: no heat in bake, very long preheat, won't reach temperature, uneven baking
• Visual clues: blistering, cracking, breaks, or burnt spots on the element sheath

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the element from the oven cavity; remove mounting screws/bracket
• Pull the element forward carefully and move wires one at a time to the new element; do not let wires slip back into the insulation
• Ensure terminals are fully seated and the mounting plate is secure before restoring power

The Bake Element is an OEM part for Whirlpool ranges. This heating element is responsible for providing the necessary heat for baking and roasting by distributing heat evenly throughout the oven cavity, ensuring consistent cooking results.

Over time, bake elements can wear out or fail due to regular use, exposure to high temperatures, or accidental damage during cleaning. 

Symptoms of a bad bake element include:

• Oven not heating to the set temperature
• Uneven cooking or baking results
• Visible signs of damage such as burns, blisters, or breaks in the element
• The element not glowing red when in use

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Small Surface Element is an OEM part for Whirlpool electric ranges and cooktops. This heating element is responsible for providing heat to a specific area on the cooktop, typically used for smaller pots and pans. It ensures even and efficient heating, allowing for precise cooking control.

Causes of a bad surface element can include regular wear and tear, overheating, or electrical malfunctions. A malfunctioning surface element can result in uneven heating, longer cooking times, or no heat at all.

Symptoms of a bad small surface element include:

• The element not heating up
• Uneven or inconsistent heating
• Sparks or electrical arcing when the element is turned on
• Visible damage or discoloration on the element

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Single Radiant Heating Element for Range is essential for maintaining consistent and efficient heat in your Samsung range. This genuine OEM part is specifically engineered to deliver reliable performance, ensuring your cooking surfaces reach and maintain the desired temperatures effectively. Built with durability in mind, the heater radiant-single provides long-lasting service, reducing the need for frequent replacements and saving you time and money. Compatible with a wide range of Samsung ranges, this heating element guarantees a perfect fit and easy installation, allowing you to quickly restore your appliance's functionality. By choosing the Single Radiant Heating Element for Range, you benefit from improved cooking precision and uniform heat distribution, enhancing your overall kitchen experience. Whether you are repairing a malfunctioning range or upgrading an older model, this genuine OEM part offers a trusted solution to keep your Samsung range operating smoothly. Ensure your appliance performs at its best with this high-quality, reliable heating element.

The Broil Element is an OEM part for Whirlpool ranges. This part provides the intense, direct heat necessary for broiling. This part is located at the top of the oven cavity and is essential for achieving high temperatures needed for tasks like browning and searing.

Causes of a bad broil element can include electrical issues such as short circuits, damage from spills or food debris, and general wear and tear from repeated use.  

Symptoms of a bad Broil Element include:

• The oven not reaching broil temperatures
• Inconsistent or uneven broiling
• The element not glowing red when in use
• Visible signs of damage or burning on the element

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

2450w, low rise, attached ring

Restore even, reliable bottom heat with this hidden bake element assembly. Located beneath the oven floor, it delivers the heat needed for consistent preheating and baking when the original element is burned out or damaged.

• Supplies primary bottom heat during Bake cycles for electric ovens
• Helps achieve normal preheat times and maintain set temperature
• Replaces an element that is open/shorted or visibly blistered/broken
• Symptoms can include no heat in Bake, very long preheat, or uneven baking results

• Disconnect power at the breaker before servicing
• Remove oven racks and oven floor panel to access the hidden element
• Note wire positions; transfer and reconnect leads one at a time to the new element
• Inspect wiring and high-heat insulation; repair/replace any damaged connectors before reassembly

The bake element is the oven's primary lower heat source. Replacing a failed element restores proper preheating and even baking performance when the oven won't heat or struggles to maintain temperature during the bake cycle. What it does

• Provides the main heat for the bake cycle in electric ovens
• Common failure symptoms: no heat on bake, very slow preheat, or uneven baking
• Visible damage such as blistering, cracks, or burn spots on the element indicates replacement is needed
• Helps the oven reach and hold set temperature when functioning correctly

• 1 bake element

• Disconnect power at the breaker before servicing to prevent electrical shock
• Remove oven racks; access the element mounting screws from inside the oven cavity
• Carefully pull the element forward, support the wires, and transfer the connectors one at a time to avoid losing them behind the liner
• Ensure terminals are fully seated; do not overtighten mounting screws, then restore power and test bake

Restore reliable heat on your coil-top range with this 8-inch surface coil element assembly. It replaces a burned-out or damaged large burner so pots and pans heat evenly and respond predictably.

• Provides the electric heating surface for the 8-inch burner position
• Common fix for a burner that won't heat or heats intermittently
• Replaces a coil that is broken, blistered, or visibly burned
• Resolve uneven heating or hot spots on the element

• Disconnect power and let the appliance cool completely before servicing.
• Access and procedure vary by model; your product documentation.
• Handle the element carefully; avoid bending the coil or terminals.
• Inspect the burner receptacle and wiring for heat damage; replace if worn or loose.

This dual radiant surface element restores even, responsive heat to a smooth-top range or cooktop. It replaces a failed burner so the inner and outer rings heat correctly for dependable everyday cooking.

• Provides heat to a dual-size cooking zone beneath the glass surface
• Works with the surface control to use the inner ring alone or both inner and outer rings
• Common symptoms: burner won't heat, only one ring heats, slow or uneven heating, visible scorching or damage on the element
• Helps restore consistent temperature control and full dual-ring operation

• Disconnect power at the breaker before servicing; elements carry high current
• Lift or remove the cooktop to access the element
• Note wire locations and transfer any mounting brackets/clips from the old element
• Center the element under the burner outline and secure all connections before restoring power

The Broil Element is an OEM part for GE ranges. This part provides the necessary heat for broiling, located at the top of the oven cavity and designed to deliver even and intense heat for broiling foods.

Causes of a bad broil element can include electrical issues such as short circuits, physical damage from impacts or heavy usage, or wear and tear over time.  

Symptoms of a bad broil element include:

• The broil element not heating up
• Uneven or insufficient broiling results
• Visible damage such as blisters or breaks in the element
• The oven not reaching the desired broiling temperature

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement part is a broil element, and it is intended for use in different types of kitchen appliances. This is a genuine replacement part made by General Electric. The broil element is typically found inside an oven or range and is part of the heating mechanisms that help cook or bake food. The broiler heats from the top, inside area of the appliance and helps with specific things like melting cheese or crisping the tops of dishes.A new broil element might be needed if the current broiler is not heating up at all, or not heating up enough. If the broil element is working properly the user should feel the heat coming from the top area of the range. It is also common to see the broil element turn bright red during use, displaying that there is heat coming off the unit. If the element is attached properly, but still unable to heat, it might be time to replace this part. Be sure that the current element is cooled down before beginning to attempt this repair. This part is sold individually and is sourced directly from the manufacturer. This element is a genuine OEM replacement part.

This broil element is the oven's upper heating element. It delivers intense top heat for broiling and finishing, restoring proper broiler performance when the original element is open, warped, or visibly damaged.

• Provides upper radiant heat during broil and top-browning cycles
• Typical symptoms: broiler won't heat or glow; food won't brown on top; uneven broiling
• Replace if the element is cracked, blistered, pitted, or broken
• Restores consistent top heat and broiler function

• Disconnect power at the breaker before servicing; allow the oven to cool
• Remove oven racks; take out mounting screws and gently pull the element forward
• Transfer the two wire leads one at a time; support wires so they don't slip back into the cavity; ensure snug connections
• Reinstall hardware, restore power, and test the broil cycle