Cooktop Switch

This dual infinite switch controls power to a dual surface burner on an electric range or cooktop. Replacing a failed switch restores smooth heat control and proper inner/outer ring selection for accurate simmer-to-boil performance. What it does:

• Regulates power sent to the inner and outer sections of a dual surface element
• Provides variable heat levels from low to high
• Lets you select small (inner) or large (dual-ring) cooking zones
• Common failure symptoms: burner stuck on high or won't turn off, won't heat or heats erratically, cannot switch between inner-only and dual-ring modes

• 1 dual infinite surface element control switch

• Disconnect power at the breaker before servicing
• Access the control panel; remove the knob and switch mounting hardware as required by your model
• Label or photograph wiring and transfer each wire to the same terminal on the new switch
• After reassembly, test both inner-only and dual-ring settings to ensure proper operation

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

This 3-speed blower switch controls the exhaust fan in your range hood, allowing you to select low, medium, or high airflow. Replacing a worn switch can restore dependable ventilation and proper speed control. What it does:

• Selects low, medium, or high fan speed by routing power to the blower motor
• Helps resolve a fan that will not run, runs only on one speed, or will not change speeds
• Can address a switch that feels loose, sticks, or works intermittently

• 1 three-speed blower switch

• Disconnect power at the breaker before servicing
• Access the control area; note wire locations (or take a photo) and transfer wires to the new switch one at a time
• Ensure push-on terminals are fully seated and secure
• Test all fan speeds before reassembly

This ignition switch controls the spark to your gas burner or oven igniter so burners light reliably when you turn the control. Replacing a faulty switch can restore consistent ignition and safe operation. What it does:

• Sends the electrical/spark signal to the igniter so the burner lights
• Used when a control knob produces a spark to ignite a gas burner
• Common symptom: burner won't light or requires multiple attempts to ignite
• Common symptom: control produces no spark or feels intermittent when turned

• Disconnect power and shut off the gas supply before servicing
• Label and photograph wiring before disconnecting to ensure correct reconnection
• Inspect connector and mounting; test for continuity with a multimeter if troubleshooting

This switch/wire lead assembly is used on select ranges and wall ovens to control a specific function. Replacing a worn switch restores positive on/off control and reliable power flow through the attached leads. What it does:

• Opens or closes the circuit for the assigned feature when actuated
• Routes power through the attached leads to the controlled component
• Symptoms can include: feature won't start, won't turn off, intermittent operation, or heat-discolored/burned terminals or wires
• May feel loose or fail to click/hold position compared to normal operation

• One switch with attached wire leads

• Disconnect power at the breaker before servicing
• Access the control panel or mounting area; note wire locations (take a photo for reference)
• Transfer wires one at a time to the new switch; reuse original mounting hardware
• Restore power and test the function before final reassembly

The Switch/Wire Harness is an OEM part for GE gas cooktops featuring digital controls. It relays input signals between interactive panels and control modules. 

Causes of failure involve physical stress cracks from repeated flexing, pinched wiring compromising conductivity, and insulation degradation over extended use.

Symptoms of a faulty harness include:

• Unresponsive burner/knob selections   
• Inability to adjust flame heights or temperatures accurately
• Intermittent or unstable power to ignition/control systems

This OEM part is also compatible with Hotpoint and RCA gas cooktop models.

Color: Black. Instruction sheet included.

This top burner valve switch mounts to a surface burner gas valve and closes the ignition circuit when you turn the knob to Lite. Replacing a worn switch restores dependable sparking and stops intermittent or nonstop clicking at the burners.

• Mounts on the surface burner valve and closes the ignition circuit at the Lite position
• Signals the spark module to fire the igniters so the burner lights
• Helps ensure quick, consistent burner ignition
• Common symptoms: no spark at a burner, intermittent ignition, or continuous clicking with knobs in Off

• Disconnect power and shut off the gas supply before servicing
• Pull off the burner knob and remove the control/manifold panel to access the valve switch
• Transfer wires one at a time and align the switch correctly on the valve stem; avoid overtightening
• Reassemble, restore power, test for spark with gas off, then relight and check for leaks

The Switch is an OEM part for LG ovens. This switch is responsible for turning the oven light on and off when the door is opened and closed. It ensures that the oven light operates correctly, providing visibility inside the oven cavity when the door is opened.

A bad oven door light switch can occur due to electrical issues, wear and tear, or other internal malfunctions. If you notice symptoms such as the oven light not turning on or off when the door is opened or closed, it may be time to replace the light switch.

Symptoms of a bad switch include:

• Oven light not turning on when the door is opened
• Oven light not turning off when the door is closed

Ensure proper function in your LG oven by replacing the faulty switch with this genuine OEM part.

This LG replacement part is also compatible with select Kenmore models.
 

This surface burner infinite switch sits behind the knob and regulates power to the cooktop/range element. Replacing a failed switch restores accurate heat settings so the burner can turn on, modulate properly, and shut off as expected.

• Regulates on/off cycling of the surface element to achieve the selected heat level
• Sends power to the burner based on knob position
• Common failure symptoms: burner won't heat, only runs on high, won't shut off, or heats erratically
• Knob turns but the burner does not respond

• Disconnect power at the breaker before servicing; surface elements operate at high voltage
• Pull off the knob and remove the control panel/backguard as needed to access the switch
• Transfer wires one at a time from the old switch to the matching terminals on the new switch
• Align the shaft to fit your knob, reassemble the panel, restore power, and test operation

This limit switch is a safety control for compatible cooking appliances. It opens or closes an electrical circuit when a preset limit is reached—commonly temperature or travel—helping protect components and ensure proper operation of heating and latch systems.

• Monitors a specific limit at its mounting point (temperature or mechanism travel, depending on model)
• Opens/closes the circuit to interrupt or allow power to related components
• A failed switch can prevent heating, stop self-clean from starting, or keep the door from locking/unlocking
• Helps protect wiring and controls from damage during abnormal conditions

• Disconnect power to the appliance and allow all components to cool before servicing
• Access location varies by model; take photos and label wires before removal
• Transfer wires one at a time to the new switch; secure with existing hardware
• If the old switch tripped due to overheating or binding, inspect fans, vents, and latch/linkages to correct the root cause

This infinite surface element switch controls the heat output of a cooktop/range element. Replacing a worn switch restores smooth, reliable temperature adjustment for the designated Flex element, preventing issues like stuck-on-high heat, no heat, or erratic cycling.

• Regulates power to the surface element by cycling on and off at the selected setting
• Dedicated control for the unit's Flex element circuit
• Common failure symptoms: element won't heat, only heats on high, won't shut off, or heats inconsistently

• Disconnect power at the breaker before servicing to avoid electrical shock
• Pull the control knob straight off; access the switch from the control panel and note its orientation
• Label and transfer wires one at a time to matching terminals on the new switch
• Reassemble, restore power, and test all heat settings for proper operation

This dual infinite switch kit replaces the pair of infinite switches that control surface-burner heat on compatible electric ranges, restoring smooth, adjustable burner temperature and reliable heat response for proper cooking performance. What it does

• Replaces the infinite switches that regulate power to surface burners for precise heat control.
• Fixes symptoms like burners that won't heat, won't change temperature, or only operate on a single setting.
• Addresses intermittent or inconsistent burner output and erratic control behavior.
• Restores proper knob-response when the original switch fails or loses contact.

• Disconnect power at the breaker before accessing the range back or control panel to avoid shock.
• Handle wiring terminals carefully; match wires by color/position and secure connections firmly.
• Test burner operation after installation and reassemble panels per the service manual.

This replacement switch restores reliable on/off control for a specific function in your appliance, helping the selected feature respond consistently. A worn or failed switch can cause the feature to be unresponsive, intermittent, or stuck on.

• Opens and closes an electrical circuit to start/stop a function
• Common symptoms include no response, intermittent operation, or a feature that won't turn off
• Can be checked with a multimeter for continuity when actuated

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the control area to reach the switch; note/photograph wire positions
• Move wires to the new switch one at a time and secure connections
• Reassemble panels, restore power, and test operation

Oven light switch.

Replacement infinite switch that restores variable heat control for a surface heating element on an electric range, letting you adjust burner temperature smoothly and accurately. What it does:

• Regulates power to a surface heating element so the burner produces the selected heat level.
• Replaces a failed or worn rotary control that no longer changes element output.
• Common symptoms: burner won't heat, only heats at one setting, temperature jumps or fluctuates, or knob turns with no effect.
• Fits behind the console and connects to existing element wiring and control knob.

• Disconnect the appliance power before removing the console or control panel to avoid electrical shock.
• Confirm wire locations and take a photo before disconnecting to ensure correct reconnection.
• Secure the switch in place and reconnect wires firmly; test all settings after reassembly.