Crosley Parts

Ordered replacement parts Read more

Touch up paint Read more

I watched the videos for both jobs, which were excellent and "spot on" for the repair jobs.It didn't take me an hour to replace both lines. Keep up the good work on helping us repair and save money doing our own work. Ken Read more

Replaced solonoid. Video was very helpful. Parts came in the time frame given when I ordered the part. (1.7 days). Without the video I would have called a repairman. Thanks . Read more

REPLACED DEFROSTER, CONDENSER FAN MOTOR AND DEFROST THERMOSTAT. Read more

Ordered the parts from ApplianceParts Pros.com and saved the $100 service call. The fix was easy, complete instructions enclosed. Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

First we tried to change the filter. Water was leaking from the area of the filter when we changed the filter. We purchased an "original" Fridgidaire filter, no change. Did some research on the internet and decided to change the two tubes and the filter valve (at the back of the filter housing). Must have been the right diagnostic and the right part to make the repair, Gave me an opportunity to clean the condenser coils as well. After 6 years of service they needed it badly. Read more

• Will not agitate
• Spins slowly
• Burning smell
• Pumps but will not spin

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

Replaced the timer - This should have been a VERY easy repair however, there is a clip (holding the timer to panel) on the bottom of timer than must be removed with a pair of pliers. There is absolutely NO room to access this clip so I had to take apart much of the dryer to gain access. What should have been a 15 minute repair turned into a frustrating hour. Read more

It took less then 15 min. Read more

Replaced Thermal Cutoff sensor. Read more

We bought a new ice guard and installed it. It is working really good now. Read more

• No heat or not enough heat
• Takes too long to dry

Since finding out pulley on motor is factory installed, I had to order a new motor with new pulley on it. I could not remove old blower wheel from old motor, no matter how hard I tried so I had to purchase new blower wheel and new blower housing. I am super happy finding Appliancepartspros.com the prices, and my experience was great! I basically removed everything step by step, and then replaced with the new parts step by step. I had help by watching videos that were provided online before and... Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more