Door, Door Glass & Parts

This inner oven door glass assembly replaces damaged or cracked interior glass to restore a clear view into the oven cavity and help maintain proper heat containment. Designed to fit as the inner glazing panel in compatible Frigidaire oven doors. What it does:

• Replaces cracked, shattered, or fogged inner oven door glass
• Restores clear visibility to monitor cooking without opening the door
• Helps maintain oven heat containment and consistent cooking performance
• Reduces risk of injury from broken glass when the door is damaged

• One inner oven door glass assembly

• Installation may require removing the oven door and separating door panels; follow the manufacturer's service instructions
• Handle glass carefully and wear cut-resistant gloves and eye protection
• Ensure all fasteners and any gasket or trim pieces are reinstalled per OEM guidance

This inner door frame is the interior support trim that helps secure the door assembly and provides a finished surface inside the appliance door. It restores proper fit and a clean appearance when the original frame is cracked or damaged. What it does:

• Provides structural support for the inner door panel and helps hold components and liners in place
• Restores proper alignment so the door closes evenly and seals correctly
• Replaces cracked, warped, or broken frame sections that can allow rattling or gaps
• Helps maintain the correct interface between the door and the gasket to prevent airflow issues

• Disconnect power to the appliance before beginning any repairs.
• Removal typically requires taking off the door trim or liner and using basic hand tools; keep fasteners organized.
• Handle the frame and door panels carefully to avoid scratching or bending other surfaces.

This replacement frame restores the appliance's outer trim and helps hold the control/door area together for a clean, finished appearance. It's a direct-fit exterior trim piece that replaces damaged or worn frames. What it does:

• Replaces a cracked, chipped, warped or bent trim/frame that affects appearance
• Secures and aligns the surrounding control or door components to reduce gaps and rattles
• Covers internal edges to help keep out dust, moisture and debris
• Restores the original look after impact or wear

• Disconnect power to the appliance before starting any repair
• Remove required trim, screws or clips to access and replace the frame; keep fasteners for reuse unless damaged
• Handle edges carefully—trim pieces can be sharp; use proper hand protection

Color: Black

This control panel is the appliance's electronic user interface that lets you start cycles and adjust settings. Replacing a faulty panel restores reliable button or touch responses and on/off control of the unit. What it does:

• Provides the front user interface for selecting functions, settings, and cycles
• Transmits user commands to the range/oven control board for operation
• Commonly replaces panels that are unresponsive, intermittently working, or showing control/display errors
• Helps resolve issues where buttons, touch keys, or indicator lights don't respond

• Disconnect power at the breaker or unplug the appliance before starting
• Handle glass or plastic surfaces carefully to avoid scratches or damage
• Basic hand tools usually required; save mounting screws and brackets from the old part

This barrier screen is the molded door air baffle that helps direct and control refrigerator airflow to maintain proper cooling and protect interior components. It restores intended air circulation for more even temperatures. What it does:

• Directs cold air through the door to balance temperatures across compartments
• Prevents unwanted drafts and helps reduce hot/cold spots inside the refrigerator
• Helps keep vents and internal components protected from debris
• Reduces frost buildup caused by disrupted airflow

• Disconnect power before starting any repair to avoid electrical shock
• Remove the door bin or liner as needed to access the mounting clips
• Align the tabs and press until clips engage; do not force or pry on brittle tabs
• If mounting hardware is damaged, replace clips to ensure a secure fit

This lid washer cushions and spaces the washer lid hinge so the lid opens and closes smoothly and reduces wear. It helps restore proper lid alignment and quiet operation on compatible top-load washer models. What it does:

• Provides a bearing surface at the lid hinge to prevent metal-on-metal contact
• Reduces lid wobble, scraping, or grinding noises during opening and closing
• Helps maintain correct lid spacing and alignment for secure closing
• Prevents premature wear of hinge components by absorbing friction

• One lid washer

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Access the lid hinge per your model's service instructions; remove hinge fasteners to replace the washer
• Handle small parts carefully and keep track of any related clips or screws

This genuine OEM part is a washer lid. The washer lid is the main piece that covers the washer. Over time, a washer lid can become damaged to the point where it no longer closes securely. If the washer lid is no longer closing all the way or is severely cracked or damaged, it will need to be replaced.To replace this part, start by making sure the washer is unplugged. After it has been powered off, proceed to take a putty knife to lift to release the two retaining clips that secure the washer's main top. Once released, proceed to remove the lid lock assembly wire connector. Fully remove the main top and set it upside down. Release the tension on the lid springs and detach the springs from the main top and hinge bars. Using a Phillips head screwdriver, remove the screws that secure the hinge bars to the lid. Push the hinge bars through the bearings then twist the bars to remove them. This will separate the lid from the main top. Take the new lid and align it with the main top. Insert the hinge bar between the main top and bearing while threading the screws to secure the new top. Reinstall the top panel and connect the wire harness. This replacement part is sourced directly from the manufacturer and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand washers.

This door frame assembly replaces a damaged or cracked outer door frame to restore the washer/dryer door's appearance and structural support. It helps secure the door glass and maintain proper door alignment for safe operation. What it does:

• Replaces a broken, cracked, or warped outer door frame to restore form and function
• Supports and secures the door glass/window to prevent rattling or movement
• Helps maintain correct door alignment so the latch and seal engage properly
• Can reduce drafts, leaks, and vibration caused by a damaged frame

• Disconnect power (and water if applicable) before starting any repair
• Handle glass and frame edges carefully; wear gloves and eye protection
• Retain original screws and mounting hardware unless replacement parts are supplied
• Check door seal/gasket and latch engagement when reinstalling to ensure a proper fit

This is a complete microwave oven door assembly that restores a damaged or non-sealing door so the oven operates safely and retains heat. Use it to replace a cracked, bent, or otherwise compromised door assembly. What it does

• Replaces the full door structure including the frame and glass panel so the microwave can close and seal properly.
• Restores proper door alignment and latch engagement when the door is bent or won't stay closed.
• Prevents heat and steam from escaping through damaged seals or cracked glass.
• Helps restore normal operation when the oven won't run due to a door that fails to close securely.

• Disconnect power to the appliance before starting any repair.
• Handle glass and the assembled door carefully; use gloves and eye protection to avoid cuts.
• Align hinges and engage the latch fully when mounting; test door operation before use.
• If the door is heavy or awkward, have a second person assist to avoid dropping or damaging the part.

This door kit replaces a damaged or worn outer door assembly to restore appearance and sealing of the appliance door. It provides a factory-style replacement that lines up with existing hinges and latches for proper operation. What it does

• Replaces a cracked, dented, or cosmetically damaged outer door panel
• Restores a flush fit and helps maintain proper door alignment
• Helps reduce air leaks and improves closure compared with a damaged door
• Compatible with applications that specify this exact door kit part number

• One complete door kit

• Installation generally requires removing the old door and transferring any internal components per the service diagram
• Use proper support when handling the door to avoid dropping or bending the assembly
• Disconnect power to the appliance before starting work and follow the manufacturer's safety instructions

Color: Black

This inner door glass is the replacement glass panel that fits inside the appliance door and restores a clear, intact viewing surface. Replacing a damaged inner glass helps maintain door integrity and normal operation. What it does:

• Replaces cracked, chipped, or broken inner door glass to restore a safe viewing window
• Prevents loose glass shards and helps the door close and seal properly
• Restores a clean, clear view into the appliance cavity without affecting exterior trim
• Matches the OEM inner glass design for proper fit and alignment

• 1 inner door glass panel

• Recommended for experienced DIYers; handle glass carefully to avoid cuts
• Remove power and follow manufacturer door-disassembly steps before replacing the inner glass
• Use appropriate fasteners and gaskets from the original assembly; do not force-fit the glass
• Inspect surrounding door parts (brackets, clips, seals) and replace any damaged pieces to ensure proper reassembly

This inner oven door glass replaces a cracked or damaged oven door window to restore visibility and help the door seal properly. It fits behind the exterior door panel and provides a clear view of the oven cavity while resisting heat. What it does:

• Replaces cracked, chipped, or shattered inner oven door glass
• Restores clear visibility into the oven for safe cooking monitoring
• Helps maintain proper oven door seal and reduces heat loss
• Prevents loose glass fragments from entering the oven cavity
• Compatible with oven door assemblies that use a single inner glass panel

• Disconnect power to the appliance and ensure the oven is completely cool before beginning.
• Wear cut-resistant gloves and eye protection when handling glass to avoid injury.
• Removal usually requires opening the oven door and removing fasteners or clips; keep track of all screws and brackets.