Dryer Control Board

Dryer won't start or has no power? This electronic control board manages dryer cycles and settings. Straightforward replacement restores function.

Fix a dryer that won't advance or shut off automatically with this timer control board. Replaces faulty timers causing manual shutoff issues.

Dryer won't shut off or timer won't advance? This mechanical timer controls cycle timing and program selections. Restores proper cycle operation.

Fix a broken or stripped timer knob that won't turn or stay engaged. This plastic shaft restores the connection between knob and timer. Simple 5-minute fix.

Fix a dryer that won't start, stops mid-cycle, or has no display. This main control board manages all electronic functions. Moderate DIY repair.

This mechanical oven timer restores simple dial-based timing and end-of-cycle alerts so you can set cook times and receive audible reminders. It replaces a worn or non-advancing timer to bring back reliable basic timing functions. What it does:

• Advances and times cook/clean cycles so the oven rings when a set time ends
• Restores manual timing when the clock/timer no longer advances
• Replaces a timer that fails to sound the end-of-cycle buzzer
• Provides a direct, dial-based alternative to electronic controls on compatible units

• Always disconnect power to the appliance before beginning service
• Access typically requires removing the control panel or console; support the console while detaching the timer
• Align the timer shaft and knob carefully during installation to avoid damage

Fixes unresponsive controls, non-functioning display, or dryer that won't start. This main control board restores all user interface functions and cycles.

Dryer shuts off after a few seconds or won't power on? Replace the main power control board to restore power distribution and control functions.

This electromechanical timer controls the appliance's cycle sequencing so wash/dry cycles advance and complete as expected. Replacing a faulty timer restores proper cycle timing and program changes for consistent operation. What it does:

• Advances and times cycle steps so selected programs run in the correct order
• Interfaces with selector and motor to start, stop, and change cycles
• Can fail and cause symptoms like cycles not advancing, no power to cycles, or stuck on one setting
• Works with the appliance's existing wiring and mounts in the original timer location

• One electromechanical timer

• Disconnect power before starting any repair to avoid electric shock
• Access may require removing the console or control panel; keep fasteners organized
• Note wire locations or take a photo before disconnecting connectors for correct reassembly

This display assembly powers and visually reports the appliance control status so you can see settings and feedback on the control panel. It restores readable on-screen information and enables the front-panel display functions. What it does:

• Replaces the control-panel LCD and power/display electronics so the screen lights and shows information again
• Commonly used when the display is blank, dim, flickering or showing garbled characters
• Resolves unresponsive or intermittent front-panel display behavior tied to the display module
• Interfaces with the main control board to present time, temperature, and mode/status readouts

• One complete display assembly (power/LCD) as shown

• Disconnect power to the appliance before beginning any work to avoid shock
• Handle the LCD and cable connectors carefully to avoid damage; flexing or scratches can affect operation
• Access typically requires removing the control console or console bezel—keep track of screws and fasteners
• If symptoms persist after replacement, test the main control board and wiring harness for faults

Fix a washer that won't start, shows error codes, or stops mid-cycle. This main control board restores cycle operation and digital controls in about 1 hour.

Fix error codes or unresponsive controls with a new dryer electronic control board. Restores cycle selection and timing. DIY install in under 1 hour.

This main electronic control board manages oven functions and user commands so your range responds correctly to temperature settings, timers, and cooking modes. Replaces a failed board to restore control and display operation. What it does:

• Receives input from the front control panel and regulates oven heating cycles and timers
• Controls bake, broil and other cooking modes by sending power signals to heating elements
• Can cause a blank display, unresponsive touchpad/buttons, or failure to start if defective
• May trigger control-related error codes or intermittent operation when malfunctioning

• Disconnect power at the breaker or unplug the appliance before any service
• Handle the board carefully; avoid static discharge and contact with circuit traces
• Basic appliance disassembly and wire-labeling required; verify connections match before reassembly

Fix a dryer that won't start, won't heat, or won't advance cycles. This timer controls drying programs and cycle progression. Moderate DIY repair.

Dryer won't turn off or advance cycles? This mechanical timer controls cycle selection and transitions. Moderate DIY repair restores automatic shutoff.

Fix a dryer that won't advance or shuts off too soon with a new timer. Requires back panel removal and wire transfer. Moderate difficulty repair.