Dryer Control Board

This display assembly powers and visually reports the appliance control status so you can see settings and feedback on the control panel. It restores readable on-screen information and enables the front-panel display functions. What it does:

• Replaces the control-panel LCD and power/display electronics so the screen lights and shows information again
• Commonly used when the display is blank, dim, flickering or showing garbled characters
• Resolves unresponsive or intermittent front-panel display behavior tied to the display module
• Interfaces with the main control board to present time, temperature, and mode/status readouts

• One complete display assembly (power/LCD) as shown

• Disconnect power to the appliance before beginning any work to avoid shock
• Handle the LCD and cable connectors carefully to avoid damage; flexing or scratches can affect operation
• Access typically requires removing the control console or console bezel—keep track of screws and fasteners
• If symptoms persist after replacement, test the main control board and wiring harness for faults

This OEM replacement part is the main control board for dryers. The main control board is the part that controls the functions of a dryer. It is the main component that sends signals to the dryer to perform its intended functions, controlling the desired dryer settings. If the dryer is no longer turning on, spinning properly, or effectively drying, it might be time to replace the main control board. While it might seem difficult to replace this part, it's actually a simple process. First, pull the dryer forward to access the back panel. Remove the upper back panel. Push the front of the control panel and pry it up with a putty knife removing it from the mounting brackets. Disconnect any wires attached to the old control board and be sure to take note of which wires go where by taking a photo with a phone camera. Then disconnect the air hose. Remove the mounting screws from the control board. Release the locking tabs and pull the control board out of the console. Position the new board in place and pop it into the locking tabs. Reconnect the air hose to the back of the control panel, and reconnect the wires into the back of the new control board.This genuine control board is compatible with General Electric, Hotpoint, RCA, and Sears/Kenmore brand dryers.

This timer is the electromechanical control that sequences a washer's wash, rinse and spin cycles, restoring proper cycle advancement and timing for affected machines. Use this direct-fit replacement to regain reliable cycle control and predictable operation. What it does:

• Rotates through and switches washer cycle stages (fill, agitate, drain, spin) to control timing
• Replaces a worn or failed timer that causes cycles to stop, not advance, or skip functions
• Restores timed operation when a washer won't complete cycles or starts intermittently
• Interfaces with controls and motors to coordinate cycle transitions

• Disconnect power before attempting service to avoid shock or injury
• Access may require removing the control panel or console
• Retain all mounting hardware and note wiring positions; replace exactly as removed

This control board is the refrigerator's main electronic control that manages temperature, diagnostics and component operation for reliable cooling performance. Replace a failed board to restore responsive controls and system coordination. What it does

• Receives and processes signals from the user interface and sensors to run fans, compressor and defrost cycles.
• Regulates temperature by commanding cooling components based on thermostat and sensor inputs.
• Enables display functions, status indicators and diagnostic/error reporting.
• Can stop key functions if the board fails, causing unresponsive controls, no display or irregular cooling.

• One control board

• Disconnect power at the wall before attempting any service to avoid shock or damage.
• Handle the board carefully and avoid static discharge; use ESD protection if available.
• Transfer any wire harnesses or mounting hardware from the old board and secure all connections firmly.
• After installation, restore power and run diagnostics or a short test cycle to confirm normal operation.

This electronic control board governs the appliance's main functions and user interface, restoring normal operation when the original board fails. Replace a faulty control board to recover timed cycles, display responsiveness, and overall control reliability. What it does:

• Receives and processes user inputs from the console and controls cycle timing and sequences
• Sends signals to heaters, motors, valves, and relays to run the appliance properly
• Common symptoms: unresponsive buttons or display, erratic cycles, appliance won't start, or frequent error codes
• Replacing the board resolves failures tied to damaged circuitry or burnt components

• Disconnect power (unplug or shut off house circuit) before starting any repair
• Handle the board by its edges and avoid touching components; observe ESD precautions
• Verify the appliance model and part number match before ordering and installing

This electronic control board regulates oven functions and user interface, restoring consistent controls and cycle operation. It replaces a failed console module to help return accurate temperature control, timed cooking and display responsiveness. What it does:

• Reads user inputs and sends commands to bake/ broil/ convection elements and timers
• Manages oven temperature regulation by communicating with sensors and relays
• Restores display, touchpad or knob-responsive controls and cycle selection
• Resolves symptoms like unresponsive controls, incorrect cycle starts, or intermittent operation

• Disconnect power at the breaker before starting work to avoid shock
• Ground yourself and handle the board by edges to protect against static damage
• Minor disassembly of the console or back panel is typically required; retain all screws and connectors

This main electronic control board manages oven functions and user commands so your range responds correctly to temperature settings, timers, and cooking modes. Replaces a failed board to restore control and display operation. What it does:

• Receives input from the front control panel and regulates oven heating cycles and timers
• Controls bake, broil and other cooking modes by sending power signals to heating elements
• Can cause a blank display, unresponsive touchpad/buttons, or failure to start if defective
• May trigger control-related error codes or intermittent operation when malfunctioning

• Disconnect power at the breaker or unplug the appliance before any service
• Handle the board carefully; avoid static discharge and contact with circuit traces
• Basic appliance disassembly and wire-labeling required; verify connections match before reassembly

This mechanical dryer timer controls cycle selection and advances internal switches to run heating and motor circuits, letting you choose timed drying cycles and automatic transitions. Replaces a worn or non-advancing timer to restore cycle control. What it does:

• Selects and advances dryer cycles by rotating internal cams and switching circuits
• Starts and stops motor and heating circuits according to the chosen cycle
• Resolves symptoms like a timer that won't turn, dryer not advancing through cycles, or inability to select timed cycles
• Works as the user-facing control for timed and some automatic drying functions

• One mechanical dryer timer

• Disconnect power (and shut off gas supply on gas dryers) before beginning any work
• Remove the control console or access panel to reach the timer; note knob/shaft alignment for reassembly
• Handle the timer and wiring harness gently; reconnect wires to the original terminals and secure the timer before testing
• After reinstalling, restore power and run a short cycle to confirm proper function

The CONTROL BOARD is an OEM component specifically designed for Whirlpool brand electric dryers. It houses the electronic control system that monitors all cycles and safety features based on input signals. 

Symptoms of a bad control board include:

• Repeated error codes and faulty drying sequences   
• Failure to advance drying stages or tumble as intended  
• Failure to respond appropriately to input selections

As an electronic component, the control board faces wear from repetitive usage over many drying cycles. Exposure to moisture or impacted energy surges also risk damage over the years. Replacing it with this genuine Whirlpool part restores full oversight and dependable automatic operation cycle after cycle. Reliable electronic governance fulfills core drying functions.

This OEM Whirlpool replacement control board is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore dryer models. Proper monitoring streamlines laundry and maximizes performance.
 

This user interface control board replaces the oven's front control module so you can send commands and view settings. It restores responsive touch/buttons and proper display feedback for normal operation. What it does

• Receives button/touch inputs and relays commands to the oven control system
• Provides display/status feedback so settings and timers are visible
• Helps resolve unresponsive buttons, blank or incorrect display readouts, or intermittent control behavior
• Works as the main input surface for oven functions like bake, broil, timers, and temperature settings

• One user interface control board (UI board) — only items explicitly listed by the manufacturer are included

• Turn power to the appliance off at the breaker before servicing to avoid electrical shock
• Handle the board and connectors carefully; avoid touching contacts or flexing the board
• Verify connector orientation and secure mounting; test operation with power restored