Dryer Control Board

This timer controls the duration of each drying cycle by advancing through timed and automatic dry settings and signaling the dryer to stop when the cycle is complete. It mounts behind the control panel and connects to the timer knob on the front of the dryer. Replace this timer if the dryer won't start, won't advance through cycles, runs continuously without stopping, or the timer knob turns but nothing happens.

This is a 60 Hz timer that controls the duration of drying cycles in a clothes dryer. It advances through each stage of the cycle and signals the motor and heating components to turn on or off at the appropriate times. Replace this timer if the dryer will not start, the cycle does not advance, the timer knob spins freely without clicking, or if the dryer runs continuously without shutting off.

Dryer won't start, won't advance cycles, or displays PAU error? This electronic control board manages timing and functions. Moderate DIY repair.

This genuine replacement part is a user interface board for dryers. The user interface board is the circuit board that responds to the buttons located on the control panel allowing the user to adjust the dryer settings. If the dryer is no longer responding when buttons are being pressed then it might be time to replace the user interface board. Luckily this is a relatively easy repair.To replace the interface board begin by turning off the power to the dryer. Once the power has been shut off move the dryer away from the wall to gain access to the upper back panel. Remove the panel and locate the interface board. Snap it out of its brackets and remove the wire harness attached to the board. Reinsert the wire connector to the new interface and snap the new board assembly back to its original place.This OEM replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand Dryers.

Fix E91 communication errors, no heat issues, or unresponsive dryer controls. This interface board processes cycle settings and houses the display.

Fixes dryers with intermittent timing issues, unresponsive controls, or cycles that won't start. This electronic control board restores proper operation.

This is the main electronic control board that manages the dryer's operating functions, including cycle selection, temperature regulation, and timing. It receives input from the user interface and sensors, then directs power to the motor, heater, and other components accordingly. Replace this board if the dryer won't start, displays error codes, stops mid-cycle, or if buttons and cycle selections are unresponsive.

Dryer won't turn off or advance cycles? This control timer regulates cycle progression and automatic shutoff. Moderate DIY repair restores timing.

Dryer won't advance through cycles or stops mid-cycle? This timer and wiring harness kit restores accurate cycle control. Moderate DIY repair.

This is an electromechanical timer that controls the duration and sequence of the dryer's operating cycles. It advances through each stage of the drying cycle and signals the motor, heater, and other components when to turn on and off. Replace this timer if your dryer won't start, won't advance through cycles, runs continuously without shutting off, or if the timer knob turns but nothing happens.

Fix a dryer that won't shut off or has a dial that doesn't advance. This timer controls cycle length and automatic shutoff. DIY-friendly, 10-20 min.

Fix E01 error codes or a dryer that won't start with this control board replacement. Controls drying time and temperature settings. Moderate DIY repair.

Fix a dryer that won't start, has flashing cycle lights, or runs without stopping. This electronic control board restores normal cycle operation.

Fix a dryer that won't advance through cycles, runs too long, or won't shut off. This timer control restores proper cycle timing and shutoff.

This is a replacement dryer control board for an electric dryer. The dryer control board is the main electrical board that controls all the primary functions of a dryer. If the dryer has stopped working properly or is no longer turning or heating, this could mean that the dryer control board needs replaced. To replace the board, make sure the dryer is turned off and removed from power. The dryer control board will be located either on the back of the dryer or behind the user interface. Accessing it will require a screwdriver.This authentic OEM replacement part can be used in many models including the Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse and others.

Fix a dryer that won't turn on or power up. This main power control board restores electrical functions. Moderate DIY repair for experienced users.