Dryer Fuse Or Sensor

This high-limit safety thermostat monitors temperature on the dryer's heater housing and opens the heating circuit if temperatures climb too high. It helps protect components from overheating and can restore safe, reliable heating when the original control has failed. What it does

• Monitors heater housing temperature and opens the circuit on overheat
• Acts as a safety backup for the heating system to prevent damage
• Failure symptoms can include: dryer runs but no heat, intermittent heat that stops mid-cycle, or the thermostat testing open at room temperature
• Repeat trips often indicate restricted airflow; check venting and lint buildup

• One high-limit thermostat

• Disconnect power; for gas models, also shut off the gas supply
• Note wire locations, remove the old thermostat from the heater housing, and transfer wires to the new part
• Mount the thermostat flush to the housing for proper sensing; secure with existing hardware
• Before reassembly, clear lint and ensure proper airflow through the lint screen, duct, and exterior vent

The Temperature Limiter is an OEM component specifically designed for select Bosch vented dryers requiring controlled airflow temperatures. As a safety device, it restricts exhaust heat to prevent overheating risks.  

Precisely calibrated links of heat-treated alloys automatically trip circuits upon exceeding preset thermal thresholds. Protected housings shield reactive cores from moisture while allowing intended response capabilities.

Causes often involve years of exposure distorting sensitive triggering components slow to cool cycles. Intentional physical manipulation could also disable protection absent automatic overrides.

Symptoms of a bad temperature limiter include:

• Inability to sense and respond to rising exhaust air temperatures  
• Lack of functioning cool-down phases from disabled safety trips
• Continuously energized heating systems without regulation posing risks

This OEM Bosch replacement limiter is also compatible with Thermador, Gaggenau and select Kenmore dryers employing sensitive temperature cutoffs. Correct installation restores critical safety control circuits.
 

This dryer thermostat senses exhaust air temperature and opens or closes the heater circuit to keep drying temperatures consistent. Replacing a failed thermostat can restore proper heat control and help prevent overheating that can trip safety devices.

• Regulates dryer heat by cycling power to the heater based on sensed temperature
• Helps protect the appliance by interrupting heat if temperatures rise beyond its calibration
• Common symptoms: no heat or intermittent heat, long dry times, dryer runs too hot, temperature swings
• Replace if it fails continuity checks or is out of spec per your model's service information

• Disconnect power; for gas models, also shut off gas supply
• Allow the dryer to cool before servicing
• Access the thermostat on the blower or heater duct (varies by model); transfer wires one at a time and mount the thermostat flush to the surface
• Clear lint and verify vent airflow before testing operation

This multi-temperature cycling thermostat regulates the dryer's drum heat, switching the heater on and off to match the temperature setting you choose. It can help restore consistent drying if temperatures are erratic, loads run too hot, or cycles take too long.

• Maintains target temperature by opening and closing the heater circuit across multiple heat settings
• Provides calibrated temperature control for safe, efficient drying
• Failure may present as no heat or low heat, overheating, very long dry times, or inconsistent temperatures
• Intended for models with multiple temperature selections

• Unplug the dryer; shut off gas supply if applicable. Allow the appliance to cool before servicing.
• Take a photo of wire positions; move wires to the new thermostat one at a time to matching terminals and ensure snug connections.
• Remove/install mounting screws and seat the thermostat flat against the mating surface for proper sensing.
• After reassembly, clear lint passages and verify proper vent airflow.

• If there's no heat at all, also check the thermal fuse, high-limit thermostat, heating element (electric), or igniter/burner components (gas).
• Restricted venting can mimic thermostat issues and cause overheating or long dry times.

Thermister

This Thermostat is an OEM part for GE dryers. As a critical component in regulating the dryer's temperature, this thermostat ensures that the machine operates within a safe and efficient heat range. It monitors and controls the heat level, preventing the dryer from overheating while maintaining optimal drying conditions.

The need to replace the thermostat can arise from a variety of issues, including electrical problems, wear and tear, or a malfunction due to overheating. A failing thermostat can significantly impact the dryer's performance and safety.

Symptoms of a faulty Thermostat include:

• The dryer not heating up properly or overheating.
• Clothes taking longer than usual to dry.
• The dryer shuts off prematurely or not starting.
• Inconsistent heating leads to unevenly dried clothes.
• Potential safety hazards if the dryer overheats.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Thermostat is an OEM replacement part for Whirlpool dryers. The thermostat monitors the air temperature in the dryer drum and signals to the control system when to activate or deactivate heating elements.

Causes of a failing thermostat can include normal wear and tear over time. As the thermostat undergoes frequent temperature fluctuations with each use, components may gradually degrade. Physical damage from accidental impact is another potential cause.

Symptoms of a bad thermostat include:

• Inability to increase air temperature above a certain point
• Overheating errors
• Slow or incomplete drying even on high heat settings
• Socks ending up damp after an entire cycle

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Thermal Cutoff is an OEM replacement part for Whirlpool dryers. This cutoff component plays a crucial role in starting and stopping power to the dryer during operation. It does so through a sensitive thermal limiter that responds to temperature changes inside the dryer drum. 

Causes of a bad cutoff can include damage or wear to the thermal limiter over time, loosening of internal wiring connections, or issues with the cutoff's electronic components. 

Symptoms of a bad thermal cutoff include: 

• The dryer not turning on at all 
• The dryer fails to turn off after a full cycle
• Fluctuations in heat output during drying
• Buzzing or clicking noises coming from the cutoff area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This sensor harness connects the dryer's moisture sensor bars to the main wiring, helping the control or timer read moisture levels so Auto Dry cycles can advance and deliver consistent, reliable drying performance.

• Provides the electrical path between the moisture sensor bars and the control/timer
• Enables the dryer to sense wet fabrics and adjust or advance Auto Dry cycles
• A damaged or open harness can cause Auto Dry to not advance, run too long, or stop early
• Contribute to inconsistent dry times or a "Sensing" indicator that behaves abnormally

• Disconnect power before servicing
• Access the sensor bars at the front bulkhead; note wire routing and clip locations
• Transfer routing/clips from the old harness; connect to both sensor bars and the main harness plug, ensuring snug terminals and clear wire paths
• Restore power and run an Auto Dry test; inspect/clean the sensor bars and check harness continuity

Hi-limit thermostat. L210.

This internal-bias thermostat regulates dryer drum temperature by cycling the heat on and off, helping maintain consistent drying performance and protect against overheating.

• Controls the cycling temperature of the heating circuit to prevent underheating or overheating
• Helps resolve symptoms like no heat, not enough heat, long dry times, or temperature swings
• A faulty thermostat may cause overheating that can trip the thermal fuse
• Located on the blower housing on many models

• Disconnect power and shut off gas (for gas dryers) before servicing
• Access the blower housing; note wire positions and transfer one at a time
• Mount the thermostat flush to the housing for proper sensing
• After installation, run a test cycle to verify proper heating

The Thermal Fuse is an OEM part for Whirlpool dryers. This part prevents the dryer from overheating by cutting off power to the heating element if the dryer exceeds a safe temperature. It helps protect the appliance and home from potential fire hazards caused by overheating.

Causes of a bad thermal fuse can include lint buildup restricting airflow, a malfunctioning thermostat, or excessive load causing the dryer to overheat.  

Symptoms of a bad thermal fuse include:

• Dryer not starting
• Dryer not producing heat
• Dryer shutting off mid-cycle
• No power to the dryer despite other electrical components functioning

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This safety thermostat monitors temperature at the dryer's air inlet and opens the heater circuit if temperatures climb too high. Replacing a failed unit restores proper heat control and helps protect the dryer from overheating damage. What it does:

• Senses inlet air temperature and interrupts power to the heater when a high limit is reached
• Helps prevent overheating and repeat thermal fuse failures due to restricted airflow
• Failure symptoms include no heat, intermittent heat, very hot cabinet, or a burnt odor
• Supports consistent drying performance by maintaining safe operating temperatures

• 1 thermostat

• Disconnect power; turn off gas supply for gas models
• Thermostat is typically mounted on the inlet duct or near the heater/blower housing; refer to your model's diagram for location
• Move wires one at a time to the new thermostat; reuse existing mounting hardware
• After replacement, clean the lint path and verify proper vent airflow to prevent repeat failures

This limit thermostat monitors dryer temperature and opens the heating circuit if temperatures climb too high, helping protect the appliance and laundry. Replacing a failed thermostat restores reliable heat and safe temperature control. What it does:

• Monitors temperature at the heater/blower housing and opens at its limit to prevent overheating
• Helps maintain safe drying temperatures during normal cycles
• Common symptoms of a failed thermostat: no heat or intermittent heat, dryer runs too hot/overheats, or cycles end early due to overheating

• 1 limit thermostat

• Disconnect power and, if applicable, shut off gas before servicing
• Access the thermostat location per your model (typically on the heater housing or blower duct), remove mounting screws, and note wire positions
• Transfer wires to the new thermostat and mount it flush for proper sensing
• After reassembly, clear lint and verify venting/airflow to prevent repeat overheating

This thermostat is a temperature-sensitive switch used in the appliance's heating circuit. It opens and closes at a specific temperature to regulate or limit heat, helping maintain correct operation and protect components from damage due to overheating.

• Monitors temperature and switches the heating circuit on/off at its preset trip point
• Helps prevent overheating and heat-related component damage
• Failure symptoms can include no heat or underheating, overheating or burnt odors, or heat that won't shut off
• May cause intermittent heating or frequent cycling as the unit warms and cools

• Disconnect power and allow the appliance to cool completely; shut off gas supply if applicable
• Access the thermostat, note/photograph wire positions, and transfer wires one at a time to the new part
• Mount securely against the proper surface/bracket so the sensor has good contact
• Restore power and test operation; if issues persist, diagnose related heating components per the service manual

This thermostat monitors temperature and opens or closes its electrical contacts to control and protect the appliance's heating circuit. Replacing a failed thermostat restores stable temperatures and helps prevent nuisance shutdowns or persistent no-heat issues. What it does:

• Senses temperature at its mounting location and switches the circuit on/off as designed
• Protects the heating system by interrupting power when temperatures exceed its rated limit
• Helps maintain consistent operation when the original thermostat is stuck open/closed or out of calibration
• Typical symptoms: no heat or intermittent heat, overheating/safety shutdowns, or failed continuity when tested cool

• 1 thermostat

• Disconnect power (and shut off gas supply if applicable) before servicing
• Note wire locations and transfer one at a time to the new thermostat
• Mount securely in the original position to ensure proper temperature sensing
• After installation, run a test cycle and monitor operation/temperature