Dryer Heating Element

Dryer

Terminal Size: 1/4 inch. For the 5/16 inch terminal size order 5300622034. This electric dryer heating element restring coil does not include the heater housing insulators 131472100 or the terminal block 3202786.

This genuine heating element restores consistent, controlled heat so your appliance can reach and maintain the proper temperature. Replacing a failed element can resolve no-heat or weak-heat issues and bring performance back to normal.

• Converts electrical energy into heat when powered by the control
• Helps the unit achieve and hold the set temperature during operation
• Typical failure symptoms: no heat, slow or uneven heating, cycles that take longer than normal, visible damage to the element
• May trigger heat-related error codes when failing

• Disconnect power at the breaker or unplug the appliance before servicing; allow all components to cool completely
• Note wire locations and terminal orientation before removal; transfer any mounting hardware from the original if needed
• Avoid bending or striking the element; handle by the bracket/insulators
• After installation, run a test cycle to check for secure connections

Built for electric dryers that require a 240V heater, this complete heater assembly restores proper heat output. Replace a burned-out element to resolve no-heat or weak-heat complaints and return your dryer to consistent, efficient drying.

• Generates the hot air needed to dry laundry during the cycle
• Typical failure symptoms: drum turns but no heat, longer dry times, or intermittent heating
• Can be checked with a continuity test; a broken or grounded coil indicates replacement is needed
• Factory-style 240V configuration for proper operation on compatible models

• Disconnect power at the breaker before servicing
• Access the heater per your model's service procedure and document wire locations
• Move wires to matching terminals; transfer any attached brackets/sensors from the old assembly if your model uses them
• Clear lint and verify airflow before a test run to confirm proper heating and cycling

This replacement heating element restores proper heat in electric dryers designed with two-level heat. It generates the controlled heat needed for both high and low temperature cycles, helping return normal drying performance.

• Heats the air passing through the drum during drying cycles
• Supports two-level heat so high and low temperature settings work correctly
• Typical symptoms include: no heat, insufficient heat, longer-than-normal dry times, or only one heat setting working
• A visibly broken coil or an open reading on a continuity test indicates failure

• Disconnect power before servicing; dryer circuits carry high voltage
• Handle the element carefully—coils and insulators are fragile; do not stretch or deform the coil
• Note wire locations and ensure tight, clean connections during reassembly
• Clear lint and verify airflow; restricted ventilation or failed thermostats/cutoffs can lead to repeat element failure

This 240-volt heater assembly restores the appliance's ability to generate and maintain heat during operation, helping cycles reach designed temperatures for proper performance and results. What it does:

• Converts electrical energy into heat for the appliance's heating circuit
• Helps the unit reach and hold target temperatures during heat-required portions of the cycle
• Replaces a damaged, shorted, or open heating element
• Symptoms can include no heat when expected, longer-than-normal cycles, tripped breakers, or heater-related error codes

• 1 heater assembly

• Disconnect power at the breaker before servicing; 240V circuits can be hazardous
• Document wire locations and move connectors one at a time to the new assembly
• Avoid bending or striking the element; ensure secure mounting and proper clearances
• After installation, check related safety devices (high-limit, thermostats, fuses) and verify the circuit has correct voltage and continuity

This element repair kit restores a safe, solid electrical connection to an electric range/cooktop surface burner, helping the element heat consistently and reducing arcing after the original connector has overheated or loosened.

• Repairs a damaged or heat-weakened surface element connection
• Helps resolve a burner that won't heat or heats intermittently
• Addresses visible scorching, melting, or arcing at the element plug-in
• Supports a snug, reliable fit for the element prongs

• Disconnect power at the breaker or unplug before servicing; allow the cooking surface to cool completely
• Match connector orientation and move one wire at a time to avoid miswiring
• Inspect wire insulation and element terminals; replace any parts with burnt, pitted, or loose contacts
• Ensure the element seats firmly after repair and verify proper operation before regular use

This heating element generates the heat your electric dryer needs to dry laundry. Replacing a failed element restores consistent temperatures and helps resolve no-heat or long dry-time issues.

• Converts electrical energy into heat inside the dryer's heater assembly
• Typical symptoms of failure: runs but no heat, takes too long to dry, or clothes remain damp
• Visual clues can include a broken/burned coil or an open-circuit continuity test
• Restores proper drying performance when the original element has burned out

• Disconnect power before servicing; heating components operate at high voltage
• Access the heater assembly; note wiring and component positions for reassembly
• Handle the element carefully to avoid stretching or deforming the coil
• After replacement, clean the exhaust duct and check related thermostats/thermal cutoffs for continuity if heat issues persist

208 Volts

This heating element assembly is designed for 240-volt installations and restores proper heat to your appliance. Replace a burned-out element to bring temperatures back to spec and recover consistent, reliable performance. What it does:

• Generates the heat required on a 240V circuit to reach and maintain set temperatures
• Common failure symptoms: no heat or insufficient heat
• May show a visible break/hot spot on the coil or test open (no continuity)
• Intermittent or uneven heating can indicate a fatigued element or loose connections

• Disconnect power at the breaker/fuse and allow the appliance to cool completely
• Photograph/label wiring; transfer terminals to the new element one at a time
• Do not bend, stretch, or handle the coil surface with bare hands; mount securely per model guidance
• Check related high-limit/thermal devices, fuses, and wiring for continuity

This replacement heater assembly restores proper heat output in your appliance. It delivers the thermal energy needed for normal operation so your unit can reach and maintain the correct temperature and complete cycles as designed.

• Generates heat for the appliance's heating/drying/defrost function (as applicable to your model)
• Helps the unit reach and maintain target temperature for proper performance
• Common failure signs: no heat or weak heat; cycles take too long or do not complete
• May trigger heating-related error/fault codes; visible breaks or hot spots on the element; tripped breaker from a short to ground

• Disconnect electrical power before servicing; allow hot components to cool
• Wear cut-resistant gloves; internal panels and chassis edges can be sharp
• Document wire routing and mounting positions before removal; route wiring exactly as original
• After installation, ensure secure connections and clearance from metal surfaces; run a brief test cycle to verify operation

Replacement dryer heating element that produces the hot air needed for normal drying. Replaces a failed or burned-out heating coil so the dryer can heat properly and clothes will dry in expected cycles. What it does

• Produces heat for the dryer by replacing the oven-like heating coil inside the element housing.
• Common symptoms include no heat, weak or inconsistent heat, or items taking much longer than normal to dry.
• Restores proper heating when the element coil is broken, burned, or open; does not address unrelated electrical or control faults.

• Disconnect power at the breaker or unplug the dryer before beginning any repair.
• Part installs behind the dryer access panel(s); some panel removal and basic hand tools are typically required.
• Avoid contact with sharp sheet-metal edges and the heating coil surface; allow the dryer to cool completely before handling.

Restore reliable heat to your dryer. This replacement heating element generates the hot air needed to dry laundry efficiently, helping cycles reach proper temperature and finish on time when the original element has failed.

• Converts electrical energy into heat to warm air passing through the drum
• Failure modes include open coil or short-to-housing
• Common symptoms: no heat, weak heat, longer dry times, visible breaks or hotspots on the coil, tripped breaker or thermal cutoff
• Useful diagnostic step: check the element for continuity and for shorts to ground

• Disconnect power before service; elements get extremely hot and retain sharp edges
• Handle the coil carefully and avoid bending or touching the bare element; support terminals/insulators during transfer
• Move any reusable brackets, insulators, or wiring from the original as required
• After installation, check related thermostats/thermal cutoffs if heat issues persist

This heater element kit is the replacement heating assembly for select GE electric dryers. It restores the dryer's ability to generate heat so loads dry normally and cycles finish on time. What it does:

• Generates the hot air needed to dry clothes by heating incoming air in the dryer cabinet
• Replaces a failed or damaged heating assembly that can cause no heat or reduced heat
• Helps resolve symptoms such as long dry times, damp clothes after a full cycle, or a dryer that runs but produces little or no heat
• Works with the dryer's thermal controls to maintain safe operating temperature

• Disconnect power at the breaker or fuse panel before starting work
• Allow the appliance to cool and handle the element carefully; avoid bending heating coils
• Follow the dryer's wiring diagram and parts diagram for correct placement and connections

This heater assembly supplies the heating element and housing used in coin-operated dryers to produce the hot air needed for drying. Replaces a worn or failed heater module to restore normal drying temperatures and cycle performance. What it does:

• Generates and directs heat through the drum to dry clothes
• Heats only when the dryer control and motor are running
• Commonly replaced when a dryer tumbles but produces little or no heat
• Also used when a dryer trips thermal cutouts or has intermittent heating

• One heater assembly (housing with heating element and mounting hardware)

• Disconnect power before starting — this is a live-voltage component; verify power is off
• Follow dryer service manual for access, removal, and wire/harness routing
• Inspect and replace any failed thermal fuses or thermostats per OEM guidance