Dryer Parts

• No heat or not enough heat

I replaced the "heating element" which was bad.........as well as the "Thermst-fix" and "Thermal Cutoff" which are located on the side of the element mounting location while I had the dyer all opened up and the element mounting tube removed.......I also replaced the Dryer Thermister which is located on the top of the blower fan.....To get to these parts, you must open the top of the dryer which has spring latches on both sides of the front corners... they need to be pressed in (use a putty... Read more

• Will not tumble

Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more

I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more

I purchased a new replacement. Read more

It was an easy repair just screwed in. The ordering process and simple no hassle and got here fast! I will definitely order from you again Read more

I wanted to avoid pulling the drum. Luckily, my blower was easily accessed by pulling the front bottom panel. A couple of sheet metal screws were all I needed to remove the fan housing cover. I knew the fan was on reverse threads, i.e. righty-untighty. As it spins it tightens so no need for a retaining nut. I took off a screw holding on the exhaust tube and wiggled it out. I found the broken teeth inside. With the tube out of the way I was able to slide a crescent wrench in back and place... Read more

• Will not drain
• Won't start
• Will not fill with water
• Lid or door will not open

My son was doing his laundry, only to announce that the washer wouldn't rinse, spin or drain. I looked on line at new washers and was staggered to see how much they cost, our Whirlpool is 20 years old! Then I looked on Craig's list to see about getting a used washer, but when I found something that looked good, and looked up how it performed, most of them had terrible reviews. So, I looked at a video that told about the 5 most common things to go wrong and figured out it was a broken lid... Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• No heat or not enough heat

My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more

We had a problem of lint building up inside of the filter slot. Once I took a long brush and cleaned the recess where the filter slides I was able to see that the old filter was not catching all the lint. Upon closer examination I noticed that the seal around the filter had become compressed. that's when I order another filter from AppliancePartsPros.com. My new filter came within three days and my dryer has been working fine ever since then. Read more

The original issue with the dryer is that a corner of the lint screen was sticking out of the lint screen guide, and it would not stay flush with the guide. As a result, many tank top straps, waistband strings, and blankets would get caught on this corner and twist, tear, or warp my clothes. When I did my research on the issue, I kept reading that it was an issue with the lint screen that came with the dryer. So I ordered the lint screen, guide, and cover that appliance part pros recommends to... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• No heat or not enough heat
• Takes too long to dry

Since the dryer was 24 years old I opted to replace all the possible problem components, instead of just the bad one. The parts aren't that expensive and do to their age I figured it was worth it to avoid having to go back into the dryer in a few months. The repair was surprisingly easy and went pretty much as the video instruction AppliancePartPros provided with one exception. Because, my model was much older than that used in the video, I had a more difficult time replacing the Heating... Read more

I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more

It will save you the time and shipping charge if you buy a new set of lint filter and filter housing together ! Read more

• Marks left on clothes

Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered... Read more

First symptoms were squeaking drum. This is probably when new glide strips might have been all that we needed. But I put off fixing it... and I put it off some more. Noises got louder, squeaking became screeching, then it started to vibrate loudly. The front drum bearing (really just a plastic arch that the drum rides on) had broken, and with the drum in a canted position, the rear bearing sleeve got messed up too. I ordered the front drum support bearing, and also a rear drum bearing... Read more