Electrolux Parts

Fix grinding or buzzing fan noise during preheat or cool-down. This motor restores proper airflow in your oven. Moderate DIY, 30-60 minutes.

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

Replacement pulley that guides the drive belt in your dryer. Needed when the original pulley is worn, seized, cracked, or causing belt damage.

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

Burner grate for gas ranges that supports cookware over burners. Replace if cracked, warped, or damaged from heat exposure and heavy use.

Replacement handle for range oven doors. Installs on the front door panel for gripping and opening. Needed when original handle is cracked or broken.

Installation tool for mounting built-in microwave ovens. Required for proper alignment during install. Replace if missing, damaged, or worn from use.

Replacement power cord for ovens and ranges. Installs at the rear panel to restore electrical connection. Needed when original cord is frayed or damaged.

Dishwasher rack stop prevents loaded dishes from shifting forward during wash cycles. Replace if cracked, broken, or missing to secure dishrack position.

Adjustable leveling leg for washers. Securely holds machine in place while allowing height adjustment on uneven floors. Replace if stripped or seized.

Retaining ring for washer door assembly. Fits into groove to secure and space components. Replace if cracked, worn, or missing to restore alignment.

Convection fan motor that circulates hot air inside the oven cavity for even cooking temperatures. Replace if fan stops spinning or makes excessive noise during convection baking.

Refrigerator door hinge bearing. Installs between hinge and door frame to reduce friction. Replace if worn, cracked, or missing for smooth operation.

If your dryer won't heat or shuts off early, the thermal limiter may have failed. This safety device cuts power when temperatures exceed safe limits.

The EVAPORATOR INSULATOR is an OEM part for Frigidaire refrigerators. It is a heat-resistant insulating pad or wrap that surrounds the evaporator coils. The insulator works to retain cool air and prevent warmer air from entering the refrigerated compartment.  

Causes of a bad insulator can include deterioration or breakdown of insulating properties over time due to aging materials. Cracks, holes, or compressed sections of the insulator result in reduced insulation performance.

Symptoms of a bad evaporator insulator include:

• Inconsistently cool or warmer fridge temperatures 
• Frost or ice buildup on evaporator coils or surrounding areas
• Higher than normal electric bills from inefficient cooling
• Warm or cold spots inside refrigerator shelves and compartments

This OEM Frigidaire replacement insulator is compatible with some Kitchenaid, Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models.