Frigidaire Valve

This thermal cutoff is a temperature-sensing safety thermostat that helps prevent overheating by interrupting power when excessive heat is detected. Use it to restore proper safety protection in affected appliance heater or control circuits. What it does:

• Monitors temperature and opens the circuit if heat rises above the designed threshold
• Helps prevent overheating-related damage or fire risk in heating systems
• Stops power to heating elements when a fault causes unsafe temperatures
• Commonly used with ovens, dryers, and other heater-equipped appliances as a fail-safe

• One thermal cutoff

• Power must be disconnected before inspection or replacement to avoid shock or injury
• Handle the part carefully and observe wire connection orientation; replace with same type only
• If other components show heat damage, inspect the whole heating circuit and controls

This water inlet valve controls water flow into the refrigerator for the dispenser and ice maker, restoring reliable filling and ice production. It replaces a worn or failed valve to stop flow issues and intermittent filling problems. What it does:

• Controls and directs incoming water to the ice maker and door dispenser via two solenoids
• Opens and closes to allow timed fills for ice production and dispensing
• Commonly used when the dispenser produces no water or has weak flow
• Can cause the ice maker to stop filling or produce small/partial ice cubes

• Disconnect power and shut off the water supply before servicing
• Inspect and tighten water line fittings; check for leaks after reconnecting water

A replacement safety valve kit that restores a safety shutoff component to appliances, helping stop flow when a fault is detected so the unit can operate safely. Fits compatible Frigidaire appliances that use this OEM kit. What it does

• Replaces the appliance's safety valve assembly to restore proper shutoff function
• Prevents continued fuel or water flow when a fault or unsafe condition occurs
• Commonly used when the appliance fails to start, fails to heat, or shows safety-related shutdowns
• Helps resolve intermittent operation or safety trip symptoms tied to a failed valve

• One safety valve kit (single complete replacement kit)

• Disconnect power and gas/water supply before starting any repair
• Follow the appliance's service manual or wiring diagram for correct routing and connections
• Use proper tools and safety gear;
• Test for leaks and proper operation after installation and before returning the appliance to service

This replacement valve and screw assembly controls the flow at the appliance connection and restores proper operation of the related water or fluid path. It's a direct-fit service piece that replaces a worn or damaged valve assembly. What it does

• Acts as the valve element that opens and closes to allow controlled flow through the service line.
• Common symptom: reduced or no flow where the valve is used.
• Common symptom: visible leaks or dripping at the valve connection.
• Helps stop intermittent flow issues caused by a damaged valve or mounting screw.

• Disconnect power and shut off the water (or related supply) before starting work.
• Use basic hand tools; avoid overtightening the screw to prevent damage.
• Inspect nearby seals and tubing for wear and replace if needed.

This water inlet valve controls water flow to the refrigerator's dispenser and ice-making system, restoring proper water delivery when the factory valve fails. Designed as a direct-replacement valve assembly for compatible Frigidaire units. What it does

• Opens and closes to allow water into the ice maker and door dispenser when signaled
• Prevents water flow when the dispenser or ice maker is inactive
• Common symptom: dispenser or ice maker does not dispense water or fills slowly
• Common symptom: water intermittently flows or the ice maker fails to fill

• Disconnect power and shut off the water supply before beginning work
• Drain remaining water from lines to limit spills during removal
• Replace mounting hardware and tubing fittings exactly as removed; use plumber's tape where appropriate on threaded connections
• Inspect connections and test for leaks after restoring power and water

This water inlet valve controls water flow to the refrigerator's ice maker and water dispenser, restoring normal dispensing and ice production when the valve is faulty or leaking. What it does

• Opens and closes to allow water into the ice maker and dispenser as commanded by the refrigerator.
• Stops water flow to prevent overfilling; a failed valve can cause no water, slow flow, or continuous filling.
• Commonly linked to symptoms such as no ice production, weak or no water from the dispenser, or visible leaks at the valve.

• One water inlet valve assembly.

• Disconnect power and shut off the water supply before starting work.
• Relieve line pressure and have towels ready for residual water when disconnecting fittings.
• Inspect and replace any worn water line fittings or gaskets; tighten connections to manufacturer torque—do not overtighten plastic fittings.