Frigidaire Valve

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

Burner won't light or flame won't adjust? This top burner valve controls gas flow to your cooktop burner. Restores proper flame control and ignition.

If your range burner won't ignite, stay lit, or adjust flame properly, the top burner valve may need replacement. Restores precise heat control.

This solenoid assembly is an electromechanical plunger actuator that restores linear motion to a linked mechanism. Replacing a failed solenoid helps return reliable actuation for latches, valves or dispenser-style components and stops intermittent or non-moving operation. What it does

• Converts electrical signals into linear movement to operate a latch, valve or dispenser actuator.
• Typical symptoms: clicking or humming without movement, intermittent operation, or complete loss of actuation.
• Restoring the solenoid can eliminate sticking mechanisms and return consistent operation.

• Disconnect power (and water, if applicable) before starting work to avoid shock or flooding.
• Remove access panels and note wiring locations; reconnect matching connectors securely.
• Handle the plunger and coil carefully; do not force into place or bend mounting tabs.
• Test operation after installation.

This water inlet valve controls water flow to the refrigerator's ice maker and water dispenser, restoring normal dispensing and ice production when the valve is faulty or leaking. What it does

• Opens and closes to allow water into the ice maker and dispenser as commanded by the refrigerator.
• Stops water flow to prevent overfilling; a failed valve can cause no water, slow flow, or continuous filling.
• Commonly linked to symptoms such as no ice production, weak or no water from the dispenser, or visible leaks at the valve.

• One water inlet valve assembly.

• Disconnect power and shut off the water supply before starting work.
• Relieve line pressure and have towels ready for residual water when disconnecting fittings.
• Inspect and replace any worn water line fittings or gaskets; tighten connections to manufacturer torque—do not overtighten plastic fittings.

Burner won't light or heat properly? This top burner valve controls gas flow to restore proper flame adjustment. Direct-fit part for gas ranges.

Oven won't heat but igniter glows? This safety valve controls gas flow to the burner. Restores heating when valve fails to open or has a gas leak.

If your range burner won't ignite, stays on high, or has uneven flames, the top burner valve may be faulty. This valve controls gas flow to each burner.

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser, restoring proper water delivery when the system won't fill or dispense. Direct-fit replacement that helps stop leaks and restore function. What it does:

• Opens and closes to let water into the ice maker and dispenser when signaled
• Stops water flow when the fill cycle or dispense cycle ends
• Common part to replace for slow/no ice production or no water from dispenser
• Replaced when valves leak or water lines fail to pressurize

• Disconnect power and shut off the water supply before starting work
• Verify tubing connections and electrical connector orientation before reassembly
• Inspect supply lines and gaskets; use proper replacement fittings if damaged

No water from dispenser or ice maker not filling? This dual-solenoid water inlet valve controls flow to both systems. Direct replacement restores operation.

If your burner won't light or the flame is too high or too low, this gas valve controls flow to restore proper ignition and flame adjustment on your cooktop.

This water inlet valve controls water flow into the refrigerator for the dispenser and ice maker, restoring proper water delivery and ice production when the valve is functioning. It replaces a failed or leaking valve to stop water loss and restore operation. What it does

• Directs and regulates incoming household water to the ice maker and dispenser.
• Stops water flow when the refrigerator is off or valves are closed to prevent leaks.
• Commonly linked to symptoms such as no water to the dispenser, slow water flow, or no ice production.
• Can cause leaking or pooling under the refrigerator when the valve body or fittings fail.

• One new water inlet valve assembly.

• Disconnect power and shut off the water supply before beginning any repair.
• Expect to access the valve behind the lower access panel or at the rear of the refrigerator.
• Tighten supply line fittings securely and check for leaks after reinstalling and turning the water back on.

Fix a burner that won't light, won't adjust, or stays on with this range top burner valve. Controls gas flow to surface burners. Moderate DIY repair.