General Electric Door Stop Or Cam Riser

This cam closure secures the freezer door hinge, helping the door align and latch properly to maintain a tight seal and consistent temperatures. It replaces a worn or broken left-side cam closure to restore normal door movement. What it does:

• Guides and supports the freezer door hinge so the door closes and opens smoothly
• Helps maintain a proper door seal to prevent cold air loss and uneven cooling
• Replaces a broken, cracked, or excessively worn cam that causes door sag or misalignment
• Works with the hinge assembly to keep the door correctly positioned during use

• Disconnect power (unplug or switch off breaker) before starting repairs.
• Remove the freezer door or hinge trim as needed to access the cam; keep fasteners organized.
• Inspect hinge and surrounding components for wear; replace additional damaged parts as required.

This left-hand freezer cam closure secures and guides the freezer door during closing to maintain proper alignment and seal. It helps restore smooth door motion and reduce gaps that can cause temperature loss or frost buildup. What it does:

• Engages with the hinge assembly to hold the freezer door closed and aligned
• Ensures consistent door travel and positive latching for a tight seal
• Helps prevent cold air leaks that can lead to frost buildup or uneven cooling
• Restores proper door feel when worn or damaged components allow sagging or misalignment

• One left-hand freezer cam closure

• Disconnect power before working on the refrigerator to prevent injury
• Removal of the door or hinge trim may be required
• Inspect hinge and mounting hardware; replace any worn fasteners for secure fit
• Test door alignment and seal after installation; adjust hinge components as needed

This stop door is the replacement dispenser flap that opens to let ice or water out and seals the dispenser chute when idle to help keep cold air and moisture inside. A simple swap restores proper dispenser operation. What it does:

• Opens and closes the dispenser chute so ice or water dispenses only when activated
• Seals the dispenser opening to reduce cold air loss and prevent warm air or pests entering
• Helps prevent frost buildup and dripping at the dispenser area when functioning correctly
• Works with the dispenser actuator/lever to ensure smooth, timed operation

• One stop door

• Disconnect power to the appliance before starting any repair
• Remove dispenser cover or bezel as needed to access the stop door; retain fasteners and springs
• Handle plastic parts gently to avoid cracking; align hinge pins and test movement before reassembling

This stop door is the dispenser door that seals the ice/water opening to prevent leaks and maintain proper dispenser operation. It replaces a worn, cracked, or stuck door to restore normal dispensing and help stop drips. What it does:

• Covers and seals the dispenser opening to prevent water or ice from leaking into the dispenser area
• Opens and closes with the dispenser actuator or motor to allow ice/water flow only when needed
• Prevents drafts and helps maintain internal dispenser insulation when closed
• Commonly used when the dispenser door is cracked, warped, stuck, or failing to close fully

• One stop door

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove dispenser housing or access panel per manufacturer diagram to reach the door assembly
• Inspect actuator linkage and mounting tabs; replace any broken clips and align door before tightening
• Handle plastic parts gently to avoid cracking; test operation before reassembling outer panels

This replacement door stop cushions and limits refrigerator door travel to protect the hinge and door edge while helping the door close smoothly and quietly. Fits where the stop mounts at the hinge or cabinet edge to control door movement. What it does:

• Acts as a cushion between the door and cabinet/frame to reduce impact and noise
• Limits door travel to prevent over-rotation that can damage hinges or seals
• Helps restore a door that slips, slams, or doesn't close smoothly
• Simple, passive part that prevents wear at the hinge mounting point

• One replacement door stop

• High-level; basic hand tools may be required. Follow appliance-specific service instructions.
• Power off and unplug the appliance or disable power to the area if working near electrical components.
• Remove the door or access hinge per the appliance manual if needed to reach the stop; align and secure the new stop in the original location.
• Inspect hinge screws and surrounding fasteners; replace or tighten as needed to ensure proper door alignment.