General Electric Divider Or Deflector

The Door Mullion is an OEM part for GE refrigerators. It is a vertical component that separates the fresh food and freezer compartments, while allowing for the seal and closure of the refrigerator doors.

Causes of a bad door mullion may include physical damage from impact or mishandling, wear and tear over time, or compatibility issues with the specific refrigerator model.

Symptoms that may indicate a need to replace the door mullion include:

• Air leaks or drafts between the fresh food and freezer compartments
• Difficulty in closing or sealing the refrigerator doors properly
• Visible cracks, breaks, or damage to the mullion itself
• Condensation or frost buildup around the mullion area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.

White vertical strip that seals between French doors on your refrigerator. Replace if cracked, broken, or worn from impact or regular use.

Ice scattering everywhere? This deflector guides cubes or crushed ice down the chute into your glass. Replaces cracked or missing deflectors in 30 minutes.

Replaces broken or cracked divider guide components in your refrigerator freezer. Restores smooth sliding and secure positioning of adjustable dividers.

This is the flip-out center rail for French-door refrigerators. It closes the gap between the fresh food doors to maintain a tight seal, helping keep cold air in and moisture out for consistent cooling. What it does

• Flips into place when both doors close to complete the perimeter seal
• Helps prevent warm-air leaks and condensation between the doors
• Supports proper temperature by reducing air infiltration
• Common symptoms: loose or broken flipper, doors not staying closed, moisture or frost at the center seam

• Includes 1 door mullion (flipper) assembly

• Disconnect power before servicing and clear items from door bins
• Open the doors and carefully release any retaining screws/clips; design varies by model
• Note spring orientation/hinge engagement and transfer any trim as needed
• Ensure the flipper moves freely and snaps closed before restoring power

This diverter valve directs wash water inside the machine, switching flow between internal paths during wash and drain/recirculation steps. Replacing a failed diverter restores proper water routing so cycles advance and complete as designed.

• Redirects water between the drain and recirculation/spray paths as commanded by the control
• Ensures correct water flow for wash, rinse, and drain steps
• A sticking or failed diverter can cause slow/no drain or no recirculation/spray
• May lead to cycle pauses/errors, unusual clicking/buzzing from the valve area, or leaks at the valve body/ports

• Unplug the washer and turn off water supply; expect residual water in hoses
• Access location varies by model; typically mounted along the pump/hoses under the cabinet
• Move hoses/clamps and the electrical connector one at a time; match port orientation
• After installation, run a rinse/drain test and check all connections for leaks

This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.

• Guides the icemaker fill stream into the fill cup/funnel during the fill cycle
• Diverts stray or excess water to the overflow path to reduce spills
• Helps prevent leaks, sheets of ice, and clumped cubes under the icemaker
• Clues it may be needed: cracked, warped, or missing guide; water dripping from the fill area

• Disconnect power and turn off the water supply before servicing
• Remove ice bin and any covers to access the icemaker fill area
• Unclip/unscrew the old diverter; align and secure the new part to the fill cup/tube
• Restore water and power; run a test fill and check for leaks

Replaces the vertical center trim between refrigerator doors. Restores clean appearance and proper sealing at the door joint when original is cracked or worn.

Replace a cracked or missing pocket stopper in your refrigerator door. This small divider prevents items from sliding past storage compartments.

Snugger module for side-by-side refrigerators. Secures and positions dividers or deflectors. Replace if cracked, broken, or missing for proper fit.

Diverter lever plate for washers. This internal component controls water flow direction. Replace if cracked, broken, or worn to restore proper operation.

Drain channel directs water from the washer tub to the pump assembly. Replace if cracked, broken, or leaking to restore proper water drainage.

Replace your refrigerator's center mullion assembly if it's cracked, broken, or damaged. This foamed divider installs between compartments.

Plastic air separator that directs cold air through refrigerator ducts on the high side. Replace if cracked, broken, or damaged to restore proper airflow.

Color: Black