General Electric Refrigerator Parts

Spring should have GOLD color.

Color: stainless. It measures about 8 inches wide by 4 inches deep.

This freezer door gasket replaces the perimeter seal on the freezer door. It restores a tight closure that keeps cold air in and moisture out, helping maintain proper temperature and reduce frost and condensation around the door. What it does:

• Seals the gap between the freezer door and cabinet to contain cold air and block humid room air
• Replaces a cracked, torn, shrunken, or warped gasket that no longer seals properly
• Helps address frost or ice near the door opening, moisture on the gasket, rising freezer temps, or a door that won't stay fully closed
• Supports consistent cooling and reduces air leaks that can lead to longer run times

• One freezer door gasket

• Unplug the refrigerator before servicing
• Warm the new gasket with hot water or low heat to relax shipping folds; do not overheat
• Remove the old gasket and clean the sealing surfaces; seat the new gasket fully in the door channel, starting at the corners
• Close the door and check for uniform contact (paper/dollar-bill test); allow the gasket to conform over 24 hours

Color: white. It measures about 16 inches wide by 2 inches high by 2 inches deep.

This refrigerator door gasket seals the fresh food compartment door to keep cold air in and humid air out, helping maintain stable temperatures and efficiency. Replace a cracked, warped, or loose gasket to restore a reliable door seal.

• Forms an airtight seal around the fresh food door to prevent warm air intrusion
• Helps maintain proper temperature and reduce moisture/condensation near the door opening
• Common failure signs: tears, gaps, warping, brittleness, door not closing flush, persistent condensation
• Air leaks can lead to longer run times or warm spots in the refrigerator

• Disconnect power before servicing
• Soften the new gasket in warm water or with gentle heat to relax folds; do not overheat
• Clean the door surface and gasket channel; transfer any retainers/screws if your model uses them
• After installation, check the seal all around (dollar-bill test) and adjust door/hinges if needed

Color: white. Measures about 26 inches wide by 20 inches deep.

This refrigerator water inlet valve controls the incoming household water supply to the dispenser and icemaker. When energized, it opens to allow water flow, helping restore reliable dispensing and proper ice production.

• Regulates water flow to both the dispenser and the icemaker
• Common failure signs: no or slow water dispensing, no ice production, small/hollow ice cubes, valve humming but no water, or water leaking from the valve body
• Electrical solenoid-operated design opens only when signaled by the control system
• Helps maintain consistent water delivery and ice fill levels

• Disconnect power and turn off the household water supply before servicing
• Place a towel or pan to catch residual water; relieve line pressure carefully
• Transfer tubing and wire connectors one at a time to the new valve to avoid mix-ups
• Check for leaks after installation; do not overtighten compression fittings

This screw is a genuine General Electric part, sold individually. This screw can be used as a replacement part for a refrigerator. A screw can suffer damage in the lifespan of a refrigerator. It can also be easily lost or misplaced. Screws are small parts and are usually installed in multiples to ensure components are reliably attached, so one screw loosening or going missing might not necessarily affect the operability of the refrigerator. However, if the components loosen or the screw suffers damage that strips the part, such as punctures or erosion to the metal material from general wear and tear or from a direct impact, the screw should be removed and replaced with this genuine OEM replacement part. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following appliance brands: General Electric, Hotpoint, RCA, and Americana.

Restore smooth, reliable door movement. This hinge cam riser fits at the lower door hinge to provide the lift and ramp action that helps the refrigerator door open/close smoothly and seal properly—reducing sag, noise, and poor sealing. What it does:

• Interfaces with the lower hinge pin to lift and guide the door during opening and closing
• Helps maintain door alignment and gasket contact for a proper seal
• Can reduce door sag, scraping, wobble, and clicking/popping noises
• Common signs it's worn: door drops or binds, won't stay closed or self-close, or shows an uneven gap

• 1 hinge cam riser

• Disconnect power and remove items from the door before servicing
• Support the door; remove the top hinge cover and screws, then lift the door off the lower hinge
• Remove the old riser at the lower hinge and install the new riser in the same orientation
• Reinstall hinges; verify gasket contact and door alignment, adjusting leveling if needed

This fan-mount grommet fits the evaporator or condenser fan assembly to isolate vibration and keep the motor aligned. Replacing a worn grommet can quiet rattles and prevent the fan blade from rubbing the housing. What it does:

• Isolates the fan motor from its bracket to reduce vibration and operating noise
• Helps maintain proper fan motor and blade alignment/clearance
• Replaces cracked, flattened, hardened, or missing grommets
• Typical symptoms: rattling, buzzing, or vibration sounds from the freezer or rear machine compartment

• 1 fan motor grommet

• Disconnect power before servicing; pull the refrigerator forward for rear access if needed
• Evaporator fan: remove the freezer's rear panel; condenser fan: remove the rear service panel
• Support the motor, remove the fan blade and mounting hardware as needed, replace the grommet, and reassemble
• Ensure the fan spins freely and does not contact the shroud before restoring power

This top pan cover sits above the refrigerator's crisper drawers, creating a flat shelf surface and supporting the bins below. Replacing a damaged cover restores usable space and helps the drawers slide, align, and close properly.

• Forms the shelf surface over the produce/crisper drawers
• Supports food items and the crisper bins beneath
• Helps drawers open/close smoothly and seat correctly
• Replaces cracked, warped, or broken covers that cause sagging or misalignment

• Disconnect power and clear items from the shelf area
• Remove the crisper drawers to access the cover
• Lift out the old cover; transfer any slides or trim from the original if needed
• Set the new cover in place and reinstall drawers; handle any glass carefully

An evaporator fan blade mounts on the evaporator fan motor to move cold air across the coils and throughout the refrigerator compartments. Replacing a cracked, warped, or loose blade restores proper airflow, temperature balance, and quiet operation.

• Circulates air across the evaporator and into the fresh food and freezer sections to maintain even temperatures
• Helps reduce frost/ice buildup on the evaporator cover by improving airflow after defrost
• Common symptoms of a damaged blade: rattling or scraping noises behind an interior panel, weak or no airflow at vents, warming in the fresh food section, or uneven cooling
• A cracked or loose blade may spin but move little air even when the motor runs

• Disconnect power to the refrigerator before service
• Access the evaporator fan behind the interior rear panel; remove the cover/shroud as required (varies by model)
• Note blade orientation; seat the new blade fully on the motor shaft and verify clearance inside the shroud
• Reassemble panels, restore power, and confirm the fan spins freely without rubbing

This slide-out freezer shelf restores a smooth, stable storage surface and easy access in the freezer compartment. Replace a cracked, hard-to-slide, or missing shelf to regain capacity, organization, and the spacing your freezer was designed for.

• Provides a level storage surface and slides forward for better visibility and reach
• Secures into the side supports/rails at the designated freezer position
• Helps maintain intended spacing and airflow between freezer sections
• Typical symptoms: cracked or broken shelf, damaged tabs, won't slide smoothly, sits unevenly, or missing shelf

• Remove items from the area and support the shelf with both hands when removing/placing
• Align with the side supports/rails and slide fully into place; verify correct front/back orientation
• Do not force; ensure it is seated in the correct slots before loading
• Handle edges carefully; wear cut-resistant gloves to prevent injury

This shelf support is the small rear rail clip that secures a refrigerator shelf or drawer rail in place. A worn or broken support can let the shelf tilt or drop, making storage unstable.

• Holds the rear of the shelf or rail securely to the cabinet wall
• Helps correct issues like a sagging, tilting, or loose shelf
• Replaces cracked, missing, or deformed supports causing poor fit
• Restores proper alignment so bins and shelves slide/seat correctly

• Unplug refrigerator before service
• Remove the shelf/bin to access the support
• Depress locking tabs and slide the old support out; snap the new one into the cabinet slot
• Ensure it's fully seated before reinstalling the shelf

This door stop mounts on the refrigerator hinge to limit the door's swing and prevent overextension that can damage cabinets, hinges, or wiring. Replacing a worn stop restores smooth, controlled door opening and proper clearance.

• Controls the door's opening range by acting as a hinge stop
• Helps prevent the door from striking walls or adjacent cabinets
• Replaces cracked, missing, or deformed stops that allow overextension
• Common symptoms: door swings too wide, scraping/clicking at the hinge, or a visibly broken stop

• Unplug the refrigerator and, if applicable, shut off the water supply
• Remove the hinge cover; support the door to relieve weight on the hinge
• Lift the door off the hinge or remove the hinge pin as required; note the stop's orientation
• Install the new stop, reassemble, and verify door alignment and gasket seal

The Pan Cover Front Gasket is an OEM part for GE refrigerators. This gasket provides a seal for the front edge of the refrigerator's crisper or pantry drawer pan cover, preventing cold air from escaping and ensuring that the contents remain at the optimal temperature for freshness.

Common causes of a bad gasket include regular wear and tear, exposure to food spills, or accidental damage from frequent opening and closing of the drawer.  

Symptoms of a bad pan cover front gasket include:

• The drawer not sealing properly, leading to temperature fluctuations
• Visible cracks, tears, or warping of the gasket
• Increased condensation or frost buildup in the drawer area
• Food items spoiling faster than usual

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.