Jenn-Air Parts

• Door won't open or close
• Door sweating
• Fridge too warm
• Clicking sound

Used floor jack to lift and secure door, left upper hinge point in place, removed lower hinge support, removed old cams and installed new ones and lubricated, secured and adjusted hinge . Read more

• Won't start

Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short... Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

Although I ordered the latch, lever and a new cup and replace the original pieces the dispenser still did not close. On further inspection it turned out to be a small spring that had fallen out of place. Once the spring was reconnected the dispensing cover worked fine. I'm still happy that I replaced the entire assembly with new parts regardless. Discovering the loose spring took the most time. Read more

Checked and found the evaporator frozen causing the fan to stop working. Took the interior panels off and applied a blow dryer to the ice, once the ice melted I cut the tabs on the grommet holding the fan since everything is thin plastic and replaced the grommet and fan. Placed everything back and found no further issues. Tools I used were a small flat head screwdriver to pry the panels off and a 1/4 socket to remove the center drawer (4), water filter cover (2), and the ice maker (2). Not too... Read more

Even though the fasteners probably only cost a few cents, I had to buy a new mullion for my fridge. $80! $80 because two nylon fasteners were poorly designed. Replacing the part was easy once I paid the *$80* for the new part. Unscrewed the old mullion. Slipped on the new $80 part. Read more

• No heat or not enough heat

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more

I used your chat and found out the year my stove was made. He also told me what part to order as one of the burners had stopped heating up. We watched the video on how to install it. My friend installed it and my stove burner now works. Read more

• Door won't close

Knowing that several things could be causing the noise, I ordered parts to cover all possibilities; once I got inside the dryer, I found the Idler Arm and Idler Pulley were worn and loose; replaced them and the Tumbler Bearings; the dryer now runs quiet again. Was going to replace the Drive Belt but believe it to be the wrong model, it was narrower and had 4 ribs whereas the old one seems to be OK and I believe has 5 ribs. The Drum Rollers and Shafts were OK Also replaced the Door Latch. Read more

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

I ordered the gasket with the model number off the frig. AppliancePartPros.com made it easy to find my part. There was also a "how to" video on the same page. I ordered the part and it got to OH the next day. Following the video guideline it took me 15 minutes to remove the door, strip out the old seal and put in the new one. I will be ordering all my appliance parts from AppliamcePartsPros.com Read more

Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more

Used screwdriver to push in plastic tabs holding old unit to the top of the refrigerator box Read more

• Will not fill with water
• Will not agitate

First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you... Read more

Replace dual infinity switch. The only difficulty is the terminal labels on the new switch did not match at all with the terminal labels on the original switch. The enclosed instructions were NOT helpful. But I contacted your representative, Johnny, and he was most helpful and patient. From my model number he located very specific and detailed instructions for how to wire the new switch. The rest of the job was easy. Your representative was outstanding. Thanks. Read more

No tools needed. Whole dairy door slipped right in. Read more