Kenmore / Sears Control Board

The Control Board is an OEM part for Whirlpool dishwashers. It serves as the brain of the appliance, controlling and regulating all functions and cycles of the dishwasher.

Causes of a bad Control Board can range from power surges or electrical issues that damage the board's components, to physical damage from moisture exposure or impact, as well as general wear and tear over time.

Symptoms of a faulty dishwasher Control Board include:

• The dishwasher not turning on or starting cycles
• Certain wash cycles or options not functioning correctly
• Error codes or indicator lights displaying on the control panel
• The dishwasher shutting off unexpectedly during cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This OEM replacement part is a relay control board for ovens. The relay control board receives signals from the main oven control board. This part regulates the oven's temperature. If the oven is no longer heating properly or maintaining temperature it might be time to replace the relay control board. Luckily replacing this board is an easy repair. To replace the relay control board, begin by turning off all power to the oven. Once the power has been shut, move the oven away from the wall to gain access to the upper back panel. Remove the panel and locate the relay control board. Snap it out of its mounting brackets and remove the wire harness connected to it. Reinsert the wire connectors to the new relay board in the correct order. Secure the new board into its mounting brackets. Reinstall the upper back panel.This genuine replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This is the electronic oven control board that manages bake and broil temperatures, oven timing, and display functions. Replacing a failed control restores accurate temperature regulation and front-panel responsiveness so your range can cook reliably again.

• Regulates oven temperature by cycling bake/broil elements per setpoint
• Controls oven timing functions and user interface/display
• Common failure signs: unresponsive buttons, error codes, inaccurate temps, no heat, or blank/erratic display
• Designed for direct replacement of the original factory control

• Disconnect power at the breaker before servicing
• Transfer overlay and wiring from the old board to the new one, noting connector positions
• Handle the PCB carefully to avoid static discharge and damage
• After installation, run a test bake cycle

The Noise Filter Assembly is an OEM part for LG dishwashers. It is designed to reduce electrical noise and interference that can affect the dishwasher's operation. The noise filter helps ensure that the electronic components function smoothly and without disruption, contributing to the overall efficiency and reliability of the appliance.

Causes of a bad noise filter assembly can include electrical surges, wear and tear over time, or damage due to moisture or physical impact.  

Symptoms of a bad noise filter assembly include:

• The dishwasher not starting or stopping unexpectedly
• Error codes related to electrical issues
• Intermittent power loss during a cycle
• Unusual noises coming from the control panel area

This OEM LG part is also compatible with some Kenmore models.

This electronic oven control board manages oven heating functions and the display on gas ranges. Replacing a failed board restores reliable ignition, accurate temperature control, and normal bake/broil operation.

• Regulates oven temperature by reading the sensor and cycling the gas burner through the bake/broil relays
• Drives the clock and function display
• Interprets keypad inputs to select modes and temperatures
• Common failure signs: oven won't heat or maintain temperature, blank or erratic display, unresponsive controls, or recurring fault alerts

• Disconnect power at the breaker and shut off gas before servicing
• Use ESD protection and handle the board by the edges
• Photograph wiring and transfer connectors one at a time; reinstall using existing hardware
• Some models require transferring the original keypad/overlay to the new board

The Electronic Control Board is an OEM replacement part for Frigidaire freezers. It functions to operate all freezer systems and components through electronic programming and input received from sensors. 

Causes of a failed control board can include moisture damage impairing circuitry over time, power surges disrupting electronics, or logic and memory failures.

Symptoms of a problematic control include:

• The freezer failing to cool or freeze properly
• Lights or other features not functioning as expected
• Error codes appearing regarding control faults  
• Sensors and components not responding to control signals

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This electronic oven control board is the brain of your range or wall oven. Replacing a failed board restores the display and keypad response and allows the appliance to heat and run bake/broil cycles reliably again.

• Controls relays for bake and broil circuits
• Uses oven sensor feedback to regulate and maintain temperature
• Powers the time/temperature display and reads keypad inputs
• Common symptoms: blank or erratic display, unresponsive buttons, F-code errors, oven won't heat or shuts off mid-cycle

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Static-sensitive component—handle by the edges and avoid touching circuitry
• Note/photograph wire locations; transfer connectors one at a time to the new board
• Mount the board in the control panel, secure connections, restore power, and test

Adaptive Defrost Control Board

This clock/timer is the range's electronic oven control. It manages the bake and broil circuits using temperature-sensor feedback and provides the digital clock and timer, restoring proper heating performance and a readable display when the original control fails.

• Controls power to bake and broil elements/ignitors to reach and hold the set temperature
• Displays clock, timer, and oven status on the front panel
• Receives keypad inputs to start/stop and adjust oven cycles
• Typical failure signs: blank or dim display, unresponsive controls, error codes, oven will not heat or maintain temperature

• Disconnect power at the breaker before servicing; this control carries live voltage
• Access the control from the backguard/control panel; remove the rear cover to reach mounting screws and connectors
• Photograph or label all wire harness connections; transfer any brackets and install the new board in the same orientation
• Handle electronics by the edges and protect from static discharge; set the clock after reassembly and test oven functions

This is the electronic control board for the oven. It manages heating functions and the display so the appliance heats accurately and responds to your selections as designed.

• Regulates power to bake and broil elements to reach and hold set temperatures
• Processes input from the oven sensor and user keypad/display
• Controls timers, clock, and on-screen status or fault indications
• Common failure symptoms include no heat, oven won't start, erratic/blank display, or recurring fault codes

• Disconnect power at the breaker before servicing; high voltage is present
• Use ESD precautions; handle the board by the edges only
• Note wire locations or take photos; move connectors one at a time to the new board
• After installation, restore power, set the clock, and test bake and broil functions

This compressor inverter control board powers and regulates the variable-speed compressor in your refrigerator by converting household AC into the controlled output the compressor needs. Replacing a failed inverter can restore compressor operation and normal cooling performance.

• Receives commands from the main control to vary compressor speed for efficient, steady cooling
• Converts AC line voltage to the controlled output required by the compressor motor
• Common symptoms of failure: refrigerator warm, compressor not running while fans/lights operate
• May also present as intermittent cooling, clicking or humming near the compressor, or visible damage on the module

• Disconnect power before servicing; this is a high-voltage component mounted at the compressor
• Note wire positions and transfer connectors one at a time; ensure all connections are fully seated
• Secure the module to the original mounting to maintain proper heat dissipation and vibration control

This refrigerator defrost timer automatically starts and ends the defrost cycle to melt frost from the evaporator coils. Replacing a failed timer restores consistent cooling performance and helps prevent frost buildup that can restrict airflow.

• Controls the timed switch between cooling and defrost to keep evaporator coils clear of frost
• Common symptoms of failure: heavy frost on the evaporator or back panel, fresh food section too warm, unit runs constantly, or won't resume cooling after defrost
• Restores proper frost removal and airflow for stable temperatures
• Designed to match the original timer's function and wiring connections for applicable models

• Disconnect power before servicing; wear cut-resistant gloves
• Access location varies by model—often in the fresh food control housing or rear machine compartment
• Photograph/label wire positions and transfer them to the matching terminals on the new timer
• Reuse original mounting hardware and install in the same orientation as the original

The Main Control Board is an OEM part for Frigidaire ranges. As the central processing unit, it coordinates bake/broil elements, lights, timers and sensory systems. Located inside the control panel area, this board continuously monitors range functions and relays information to the control display.

Causes can be splash or spill damage, power fluctuations over time, or inherent component failures due to age and usage. With proper replacement, full range functionality is restored.

Symptoms of a bad control board include:

• Knobs or buttons not working on the control panel
• Elements failing to heat properly
• Erratic temperature display readings
• Inability to preheat or maintain set oven temperatures
• Control locks that prevent range operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This dryer timer is the cycle control that advances your dryer through Timed and Auto Dry settings. Replacing a failed timer restores proper cycle progression, start/stop, and end-of-cycle shutoff.

• Advances the cam and internal contacts to move the dryer through heat, motor, and cool-down steps
• Governs run time on Timed Dry and Auto Dry cycles
• Routes power to the correct circuits in sequence; a failed timer may not advance or may stop early
• Common symptoms include timer knob not moving, dryer running indefinitely, or not starting on certain settings

• Disconnect power; for gas models, also shut off gas
• Remove knob/dial, open the console, and unmount the timer
• Label or photograph wiring; transfer wires one at a time to the new timer
• Reassemble and test both a Timed Dry and an Auto Dry cycle

This mechanical defrost timer automatically switches the refrigerator between cooling and defrost cycles. Replacing a failing timer helps clear evaporator frost so temperatures remain stable and cooling performance is consistent. What it does:

• Initiates the defrost cycle at regular intervals and then returns the system to cooling
• Interrupts compressor power and energizes the defrost heater during defrost
• Helps prevent heavy frost buildup on the evaporator
• Common failure symptoms include thick frost on the evaporator/back wall, warming in the fresh food section, the unit running constantly or getting stuck in defrost, or repeated clicking from the control area

• 1 defrost timer

• Disconnect power before servicing; components in the defrost circuit can be live and hot
• Access locations vary by model
• Note or photograph wire positions; transfer wires one at a time to the new timer
• Secure the timer in the original bracket/orientation and reassemble before restoring power

This noise filter assembly conditions incoming AC power to reduce electromagnetic interference before it reaches the control system. A failed line filter can cause no power, intermittent shutdowns, or breaker trips; replacing restores stable, reliable operation. What it does:

• Filters EMI/RFI on the power line to help protect sensitive control electronics
• Helps prevent interference that can cause no power, flickering display, or random resets
• A failing filter may trip a breaker/GFCI when the unit is plugged in or starts a cycle
• Visual clues can include scorch marks, burnt odor, or a cracked/bulged filter body

• 1 noise filter assembly

• Disconnect power before servicing; verify the outlet is de-energized
• Access is typically near the power cord entry behind a rear/top panel (varies by model)
• Label or photograph wire positions and transfer connections one by one; secure the ground
• Mount firmly and route wires to avoid pinching; reassemble and test for proper operation

• Line filter, EMI filter, RFI filter