Need Help?
Call
The Switch Gas Valve is an OEM part for GE ranges. It is responsible for controlling the flow of gas to the burners, allowing them to ignite and maintain a steady flame for cooking.
Causes of a bad switch gas valve can include wear and tear over time, buildup of debris or grease, or damage from repeated use or accidental impact. These issues can hinder the valve's ability to regulate gas flow effectively.
Symptoms of a bad switch gas valve include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Bought this switch gas valve for the non-functional burner, and it cleared right up. Read more
Dryer won't start or stops mid-cycle? This door switch detects when the door is closed, allowing your dryer to run. Simple DIY fix in 15-30 minutes.
Fix a washer that won't fill properly or overfills with this pressure switch. Controls water level sensing. DIY-friendly repair, about 5-10 minutes.
After the part arrives, I was double check to make sure I got the right part. Importantly, unplug the electrical power first before do anything, also turn off the water hose for safety. Then removed 4 screw out side panel and 2 screw in side to get lose. After all, replaced a new part and put all panel and screw back together. Finally, plug in electrical power then a water hose and test a new part just installed. So far so good, seem like everything was function OK. Again, thanks for your web... Read more
The Control Switch is an OEM part for Frigidaire ranges. This part regulates the heat output of the range's burners. By turning the control knob, users can adjust the temperature to their desired level, ensuring precise cooking results.
Causes of a bad control switch can include electrical malfunctions, wear and tear from frequent use, or damage due to overheating.
Symptoms of a bad Control Switch include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
I changed out the oven temp probe located inside the oven, and I also changed out the temperature control which is located behind the oven temperature control knob. The whole process was simple, but it took a little bit of time since we repaired it ourselves and had to located these parts inside the oven. Read more
Microwave won't start or runs only when door is pulled? Replace faulty door interlock switches. This 2-pack covers top and bottom switches. DIY repair.
First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more
Dryer won't start or tumble? This belt switch monitors drive belt tension and cuts power if the belt breaks or slips. Moderate DIY repair with video.
Remove bottom panel, remove top panel, remove drum. Had to cut old squirrel cage off. Remove motor to remove old wheel shank. Remove belt switch, and replaced. Videos from AppliancePartPros helped a lot.. Read more
Ice maker not harvesting or making ice? This rocker switch controls ice maker operation. Common fix when ice production stops despite good water flow.
Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.
I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair. Read more
This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:
The Dual Element Surface Switch is an OEM part for Frigidaire electric ranges and cooktops. It governs power distribution to the dual element.
Causes may be loose electrical terminals within the switch, defects from past power surges, or general wear over extended use.
Symptoms of a bad surface switch include:
I replaced both the large single element and the large dual element control switches. It appears the resistors were burning out. Problem seems to be fixed. Will know later when I do some simmering. Read more
Fix a washer stuck mid-cycle or showing overfill errors with a new water level pressure switch. This part detects water levels to control fill cycles.
Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more
Fix washer overfilling or won't fill issues with a new water level pressure switch. Prevents flooding and restores proper fill cycles. 10-minute DIY repair.
Replaced the water-level switch and hose. Washer works again, no overflowing since! Read more
This lid switch is the washer's safety interlock. It detects when the lid is closed so the machine can agitate and spin, and cuts power when the lid is opened to stop operation and enhance user safety.
Was set to pull the trigger on a new washer since this one was 10+ years old. Broke a $25 lid switch fumbling to get the washer open before I found the appliancepros video library. Once I got things apart the right way I was able to diagnose the problem in 5 minutes. Identified the $10 part needed. Got the $10 coupling and the $25 switch and had the washer working like new in 20 minutes. I'm pretty proud of myself.. not going to tell anyone about the $25 switch. Read more
If your range burner won't turn on or off properly, or the indicator light stays on when turned off, this infinite switch restores control. DIY repair.
Remove front panel and replaced. Received parts fast. Read more
Fix a burner that won't turn off or heat properly with this dual infinite switch. Controls both inner and outer element rings. Moderate DIY repair.
Relatively easy DIY Read more
Fix a burner that won't turn off or requires repeated knob turning. This infinite switch controls surface element heat settings. DIY repair.
The problem was fixed by ordering a switch. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.