Kenmore / Sears Washer Parts

Replaced flow meter and control valve Read more

My front loader LG washing machine wasn’t working correctly. The clothes were either coming out unwashed or completely dripping. When turning the washer on it would start up like normal and the turn off a few minutes in. Initially it was not displaying an error code, this made it very difficult to diagnose. One of the kids started a load not knowing we are having issues and it started making a clunking cringing noise, when I went to investigate the EL code was up. A few YouTube videos later... Read more

• Shakes and moves

Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more

Undid a handful of screws, put the new panel in place and screwed them back in. Read more

After the part arrives, I was double check to make sure I got the right part. Importantly, unplug the electrical power first before do anything, also turn off the water hose for safety. Then removed 4 screw out side panel and 2 screw in side to get lose. After all, replaced a new part and put all panel and screw back together. Finally, plug in electrical power then a water hose and test a new part just installed. So far so good, seem like everything was function OK. Again, thanks for your web... Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

My teenaged son took the old washer door off and apart. He replaced our glass from our washer onto the new doors and attached it to the hinge. These doors are compatible with Kenmore washer even though it says Frigidaire. Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

Symptoms: Machine was spinning and spitting a dark colored oil in a circular pattern on the floor under the machine. No strange noises, just messy. Researched issue, Gear-case bad, seal deteriorated and not preventing water from entering gear-case. The additional cam, belt etc I had replaced due to the amount of oil and transmission residue attached to them. Ordered parts, EVERYTHING parts-wise that is needed is included in gear-case package. **NOTE: You WILL need to get a whirlpool spanner... Read more

Ordered new dispenser assembly and replaced it. Fixed the problem. Read more

First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more

We are moving soon. In checking, I found that a front loading washing machine tub must be stabilized using shipping bolts. I found the correct items on line at AppliancePartsPros.com. "Chris" of your staff was very helpful. He informed me that my washer required only 3 shipping bolt assemblies, instead of the four I expected to buy. The bolts were delivered two days after my order. Read more

Replaced parts Read more

In the end, with a new coupler. But I relearned old lessons the hard way. The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned... Read more

With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more

• No hot or cold water

I order the part from appliance parts recieed it in one day and it was repaired the next day so simple watched video thanks to you all is well i highly recommend you to anyone barbara mcallister Read more