Kenmore / Sears Washer Parts

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

Fix no power, intermittent shutdowns, or breaker trips by replacing the noise filter assembly. Filters EMI from AC power to protect the control board.

Fix a leaking or broken dispenser drawer that won't release detergent or fabric softener properly. Direct replacement restores proper dispensing.

This mixing valve bracket secures the washer's water inlet valve to the cabinet, keeping the valve steady and properly aligned for hose connections. A correct-fit bracket helps reduce rattles and potential leaks caused by a loose valve.

• Mounts and supports the water inlet/mixing valve on the rear panel
• Maintains proper alignment for hot and cold supply connections
• Helps reduce vibration and rattling noises during fill
• Common signs it's needed: loose or dangling valve, misaligned hose connections, or leaks at the valve fittings

• Disconnect power and turn off both water supplies; relieve pressure before removing hoses
• Access the rear of the washer and remove fasteners securing the existing bracket/valve
• Transfer the valve to the new bracket, reusing the original hardware
• Reattach the bracket to the cabinet, reconnect hoses, restore power and water, then check for leaks

This OEM replacement part is a control board for washers. The control board is the main computer that sends signals to the washer to perform its essential functions. If the washer is no longer turning on, spinning, rinsing or draining properly, this could mean that the control board needs to be replaced. Luckily this is a relatively simple repair. To begin, start by shutting off all power to the appliance. Proceed to move the washer away from the wall to gain access to the upper back panel. Remove the upper back panel and locate the old control board. Pull it out of its mounted position and take note of the orientation of the wires attached to the old board. Reinsert the wire harness and individual wire into their correct terminals on the new board. Snap the board back into place and reinstall the upper back panel. This genuine replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Fix a washer that won't drain or makes buzzing sounds during drain cycle. This pump assembly removes water from the tub. DIY-friendly repair restores draining.

Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.

Washer won't start or advance through cycles? A failed capacitor prevents proper motor startup. This part stores energy to boost the motor during operation.

Right-hand door hinge for dryers. Replaces broken, bent, or sprung hinges that prevent the door from closing properly. Easy DIY installation.

Cap seal creates a tight barrier between cap and mating surface to prevent leaks. Replace when worn or damaged to restore secure fit. Confirm compatibility.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

Fix washer water leaking into tub or slow dripping when off. Water inlet valve assembly replacement stops fill valve leaks. Easy DIY repair with video.

Washer won't spin or agitate? Humming motor or clothes staying wet often means a failed drive motor. This repair typically takes 15-60 minutes with basic tools.

Washer making loud grinding noise during spin? A damaged motor rotor with worn splines or cracked magnets causes this. Repair guide included.

The Dryer Door Handle is an OEM replacement part for Whirlpool dryers. A dryer door handle can deteriorate due to prolonged use, repeated force when opening or closing the door, or accidental impact that causes cracks or breakage. These factors may compromise the handle's structural integrity and make it less reliable.

Color: White

Symptoms of a bad Dryer Door Handle include:

• Loose or wobbly handle
• Cracks or visible damage to the handle
• Difficulty opening or closing the dryer door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.