Need Help?
Call
Fix a washer that won't advance cycles, skips spin, or won't drain. Timer replacement restores proper cycle progression. DIY repair in under 30 minutes.
Got help from the internet to diagnose the problem. Seens that the neutral drain part of the transmission will not shift to spin unless there is a pause after draining. Thought the problem might be in the transmission but found the timer wasn;t allowing a pause after draining.therefore the machine would not spin. Replaced the timer and problem was solved. Thanks for your help, Jerry w. Read more
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Replace motor hanger , grommets, and motor coupler Read more
Restores a solid grip on your laundry center door. Replace this handle when the original is cracked, broken, or loose for smooth opening and closing.
Installed new one. About 10 minute job. Read more
Fix water leaking from your detergent drawer. This dispenser holds and releases detergent, softener, and bleach at the right time. Easy DIY repair.
I was moving my washer and dryer on to a platform when the washer slipped and the drawer came out and broke. I was going to surprise my wife with this new setup. She was out of town and was due back in 3 days. I didn't want her to see my mistake. I got on line and found AppliancePartsPros.com and I am glad I did. Their price was reasonable and fair. I order the parts I needed late on Wednesday and they were delivered early on Saturday. I watched their self help video on how to replace the parts... Read more
Fix washer water leaking into tub or slow dripping when off. Water inlet valve assembly replacement stops fill valve leaks. Easy DIY repair with video.
I ordered from this company expecting the parts to be later than they said and the parts showed up in 2 days like they said. Just before the Easter holiday even. Amazingly fast. Very satisfied!!! Washer is up and running again. Great job on getting me my parts! Thank you! Read more
This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:
Right-hand door hinge for dryers. Replaces broken, bent, or sprung hinges that prevent the door from closing properly. Easy DIY installation.
I removed the old hinges and replaced them with the new hinges. It was probably the easiest repair I've ever had to do. Read more
The Dryer Door Handle is an OEM replacement part for Whirlpool dryers. A dryer door handle can deteriorate due to prolonged use, repeated force when opening or closing the door, or accidental impact that causes cracks or breakage. These factors may compromise the handle's structural integrity and make it less reliable.
Color: White
Symptoms of a bad Dryer Door Handle include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Door latch was a snap (literally). Package included Instructions and parts for 3 different latch types and an easy identification method for each type. Just identify the correct latch type for your dryer and "Snap" it in to the cutout on the inside of the dryer door . The Door handle requires you unscrew the small sheet metal screws (three on my dryer) on the top edge of the dryer door. This allows you to separate the two dryer door halves (use a small flat blade screw driver to get the two... Read more
Washer making loud grinding noise during spin? A damaged motor rotor with worn splines or cracked magnets causes this. Repair guide included.
Replaced rotor and stator Read more
This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks. Door sensor... Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly. Timer... In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering... Read more
Left-side door hinge for dryers. Replaces broken, bent, or deformed hinges that prevent the door from closing properly. Simple installation.
This is a water inlet valve that controls the flow of water into the washing machine during fill cycles. It is an electrically operated valve that opens and closes to allow hot or cold water into the tub as directed by the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.
Ordered this part and just changed it out. Not hard once I figured out how to get in to it. Read more
Washer stops mid-spin or shows F6E1 error? The motor control board regulates drive motor speed and direction. Most DIYers replace it in 15-30 minutes.
On-line chat with AppliancePartsPros told me the error code was was for motor speed and they sent me a .pdf file on what to do to T/S it. Following the sheet I checked motor and Tack resistance and wiring - all OK, so I ordered a Motor Controller Ckt board assy. It arrived in 24 hours, during that time i watched the replacement videos and removed the old part. Upon receiving the new part I installed it (15 min), tested the washer (it worked), then put all the panels back on, pushed the washer... Read more
Fix a washer that fills slowly, won't fill, or leaks water when off with this water inlet valve. DIY repair takes about 30 minutes with basic tools.
Put in a valve Read more
This is the central wash-action component in select top-load washers. Replacing a worn or damaged agitator restores proper agitation so clothes circulate through water and detergent for consistent cleaning performance. What it does:
I have a 25 year old Kenmore washer that works well and didn't want to get a new washer as they don't make them like they used to. Upon removing the top cap of the agitator and doing an inspection, the agitator dogs were completely broken into pieces. Due to age we decided to replace the lower and upper agitator along with the agitator auger dogs repair kit. All new parts and works fine. On inspection of old parts, we probably could have gotten away with just a $5 repair for the plastic... Read more
Fix a washer that won't fill, overfills, or leaks when idle by replacing the water inlet valve. Most DIYers complete this repair in 15-60 minutes.
The error code indicated the washer wasn't getting any water, although the basket was filling to an unusually high level. After checking the inlet hoses and their connections but without opening the top cover to see the actual water level pressure switch, I went ahead and ordered the part. After receiving the switch, I opened the cover and found the original switch had fallen off it's mounting (for who-knows how long ago) and was resting against the drum. Over time, the movement of the drum... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.