Kitchenaid Gasket & Seal

This refrigerator door gasket replaces a worn seal to restore a tight, even closure around the door. A proper seal keeps cold air in and moisture out, helping maintain temperature, reduce frost, and minimize run time. What it does:

• Forms a tight seal between the door and cabinet frame
• Helps maintain set temperatures and reduce moisture intrusion
• Resolves frost or condensation at the door and frequent compressor cycling
• Common signs: torn, cracked, or warped gasket; gaps; door not sealing smoothly

• Includes: 1 door gasket

• Disconnect power before servicing; remove or secure contents for safety
• On many models, loosen the inner-liner screws or pull the old gasket from the retainer/channel to remove
• Warm the new gasket (warm water or low heat from a hair dryer) to relax shipping folds
• Seat corners first, then press the rest into the retainer; verify seal with a paper-slip test and adjust as needed

Color: Apollo Grey

This foamed-in-place refrigerator door gasket seals the door perimeter to keep cold air in and humid room air out. Replacing a worn or damaged seal restores a tight closure, reduces frost and sweating, and helps maintain consistent temperatures.

• Creates an air-tight barrier around the door opening
• Helps prevent frost, moisture, and temperature swings
• Can address issues like doors not sealing, warm spots, or long run times
• Typical failure signs: tears, cracks, warping, loose corners, or brittle rubber

• Unplug the refrigerator and clear items from the door
• Warm the new gasket in hot water or with low heat to relax and straighten it
• Remove the old seal; press the new gasket fully into the channel, seating corners first
• Close the door and verify uniform contact; adjust hinges or leveling if needed

This oven door gasket forms the heat-resistant seal between the door and oven cavity. Replacing a worn seal helps the oven reach and maintain temperature, reduces heat loss around the door, and supports even, consistent baking performance.

• Creates a continuous seal between the oven door and frame to contain heat and moisture
• Helps maintain accurate temperatures and normal preheat times
• Replaces torn, frayed, flattened, or brittle seals that allow heat to escape
• Common symptoms include hot air leaking near the door, uneven baking, and longer cook times

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Open the door and remove the old gasket, noting clip/pin locations and orientation
• Press the new gasket evenly into the retaining channel or holes; do not stretch the seal
• Close the door and verify uniform contact around the frame for a snug seal

Kitchen Aid blender dome and blade seal. Color: black. It measures about 3 inches in diameter.

Color: Grey

The Fresh Food Door Gasket is an OEM part for Whirlpool refrigerators. It is a replaceable sealing strip located around the fresh food compartment door that helps maintain cool temperatures inside.

Causes of a bad gasket can include breakdowns in the adhesive over time allowing air gaps, or physical damage such as cracks or punctures compromising the seal. 

Symptoms of a faulty gasket include:

• Frost or moisture condensation building up inside  
• Higher energy bills from the compressor running excessively
• Warm air freely entering/exiting around the perimeter 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Refrigerator Door Gasket is an OEM part for Whirlpool refrigerators. This gasket forms a seal around the refrigerator door, ensuring that cold air stays inside and warm air remains outside, maintaining the appliance's efficiency and keeping food fresh.

Causes of a bad door gasket can include regular wear and tear, mold or mildew buildup, and physical damage from repeated opening and closing of the door. 

Symptoms of a bad refrigerator door gasket include:

• Warm air entering the refrigerator, causing it to run more frequently
• Condensation or frost buildup inside the refrigerator
• Difficulty keeping the door closed
• Visible cracks, tears, or deformation in the gasket

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This part is the gasket that is used on refrigerator doors. This part surrounds the perimeter of the refrigerator door and acts as a seal to both keep the cold air in the fridge but also keep the warm air out. It is white in color.Due to normal wear and tear, the gasket may become brittle and wear out over time so that it is no longer effectively sealing the door shut. It can also become torn or cut, which would also require a replacement. A quick visual inspection can determine if it needs to be replaced. If there are folds or creases in the replacement gasket, let it soak in warm water to help straighten it back out.This gasket is compatible with refrigerator units that are manufactured by KitchenAid, Thermador, Jenn-Air, Whirlpool, and Dacor. It is sold as an individual part. This gasket comes directly from the manufacturer.

This magnetic door gasket creates a tight seal around the refrigerator door opening to keep cold air in and warm air out. A fresh, pliable gasket helps maintain temperature, reduce frost buildup, and improve efficiency.

• Forms an air-tight magnetic seal between the door and cabinet
• Helps prevent temperature swings, condensation, and frost around the door
• Common failure signs: torn/cracked rubber, gaps at the corners, door not sealing, moisture or frost near the door
• Restores proper door closure to protect food freshness

• Unplug the appliance and remove food from the door before starting
• Soften the gasket in warm water or with gentle heat to ease installation and improve fit
• Loosen perimeter screws or trim as designed, seat the gasket groove fully, then retighten evenly
• Check for uniform contact all around; adjust door alignment if needed

Freezer Door Gasket

Color: White

The Door Gasket is an OEM part for Whirlpool refrigerators. It forms an insulating perimeter around the freezer door opening to prevent warm air from entering during use.

Causes of a faulty door gasket include breakdown of sealing materials over time, cracks or loose edges that compromise effectiveness.

Symptoms of a bad freezer gasket are:

• Frost or ice buildup around the door seal
• Visible gaps allowing warm, moist air inside
• Inefficient cooling requiring excessive energy use
• Higher electric bills from poor insulation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a Whirlpool freezer gasket.If the freezer is having difficulties staying at temperature and the old gasket is damaged or off track, replacing the gasket could fix the problems. A faulty gasket could also lead to higher levels of ice and frost build up in the freezer. This could potentially raise an energy bill because it causes the freezer to stay engaged longer. Higher levels of frost build up could ultimately damage other components. Pull the old gasket out before installing the new one. It doesn't matter if the old part gets snagged or torn when it's taken out since a replacement is ready. Be sure not to break any of the fastening clips around the edge of the freezer. Slowly insert the gasket around the outer edges of the freezer lid, inserting the lip of the gasket into the cut out areas. Make sure the gasket is held tightly in place before shutting the freezer lid.This part is sourced directly from the manufacturer as a genuine OEM replacement part. This gasket is only available individually and is not included with any other parts or the original appliance. This product is compatible with Whirlpool brand freezers.

This is the front seal for the refrigerator's crisper compartment. It restores a tight barrier at the drawer's front edge so the crisper closes flush and maintains proper humidity to help keep produce fresh.

• Seals the front edge of the crisper to limit air leaks between the drawer and fresh food compartment
• Helps maintain intended humidity levels inside the crisper
• Restores smooth, flush closure of the drawer front
• Replace if the seal is torn, deformed, or missing; symptoms can include excess condensation or wilting produce

• Unplug the refrigerator and remove the crisper drawer
• Pull the worn seal off the crisper front/channel and clean the mating surface
• Warm the new seal in hot water to improve flexibility; press it evenly into place and ensure corners are fully seated
• Reinstall the drawer and verify proper alignment and closure

This flexible perimeter seal fits around the refrigerator door to keep cold air in and humid air out. Replacing a worn gasket restores a tight closure, stabilizes temperatures, and helps reduce frost, condensation, and energy waste. What it does:

• Seals the gap between the door and cabinet to prevent air leaks
• Helps maintain proper internal temperature and humidity
• Reduces frost and condensation caused by warm-air infiltration
• Corrects: visible gaps, torn/cracked gasket, door not sealing or popping open, excess moisture or frost

• 1 refrigerator door gasket

• Unplug the refrigerator before starting
• Lay the new gasket flat and warm it (warm water or low heat) to relax folds
• Remove the old gasket and clean the sealing surface/channel thoroughly
• Install starting at the corners, ensure the gasket is fully seated and evenly contacting the cabinet; adjust door alignment if needed

This gasket seals the FIP assembly to prevent air and moisture leaks, helping maintain proper temperature and efficiency. A worn or damaged seal can lead to condensation, frost buildup, or temperature fluctuations.

• Creates an airtight seal at the FIP interface to keep air and moisture out
• Helps reduce frost/ice accumulation and condensation around the assembly
• Can address issues like warm spots, frequent cycling, or visible gaps at the seal
• Restores proper sealing performance when the original gasket is cracked, flattened, or torn

• Disconnect power before servicing; wear cut-resistant gloves
• Remove cover/fasteners to access the FIP sealing surface
• Clean mating surfaces; install gasket evenly without stretching
• Verify even seating and recheck for pinches or gaps before reassembly

Jar lid seal for select household blenders. This flexible ring sits in the lid assembly to form a leak-resistant barrier at the top of the jar, helping keep ingredients contained and preventing drips while blending.

• Forms a tight, leak-resistant seal between the lid components and jar
• Restores proper fit when the original seal is cracked, flattened, or missing
• Typical symptoms: seepage around the lid, splatter from the top, or a lid that won't stay snug
• Normal wear can harden or deform the seal over time

• Unplug the blender and remove the jar from the base before servicing
• Remove the lid (and ingredient cap, if equipped); lift out the old seal from its groove
• Clean mating surfaces; press the new seal evenly into the groove without twisting
• Verify the seal sits flush; test with water before regular use