Kitchenaid Gasket & Seal

Jar lid seal for select household blenders. This flexible ring sits in the lid assembly to form a leak-resistant barrier at the top of the jar, helping keep ingredients contained and preventing drips while blending.

• Forms a tight, leak-resistant seal between the lid components and jar
• Restores proper fit when the original seal is cracked, flattened, or missing
• Typical symptoms: seepage around the lid, splatter from the top, or a lid that won't stay snug
• Normal wear can harden or deform the seal over time

• Unplug the blender and remove the jar from the base before servicing
• Remove the lid (and ingredient cap, if equipped); lift out the old seal from its groove
• Clean mating surfaces; press the new seal evenly into the groove without twisting
• Verify the seal sits flush; test with water before regular use

This replacement seal restores a tight barrier between mating components, helping prevent leaks and maintain proper performance. Install it when the original seal becomes worn or damaged to keep moisture and fluids contained where they belong. What it does

• Creates a watertight/airtight seal between connected parts
• Helps prevent drips, seepage, and moisture escaping from joints
• Maintains correct system pressure/flow at the sealed connection
• Replace if the old seal is cracked, flattened, swollen, or brittle
• Common symptoms include moisture around the joint, intermittent leaks, or residue/mineral trails

• 1 seal

• Disconnect power and, if applicable, shut off water supply before service
• Remove the old seal and clean the groove and mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved silicone grease only; seat the seal evenly without twisting
• Reassemble, restore utilities, and run a short test to check for leaks

Restore a tight, heat-resistant seal around your oven opening with this oven door gasket. It helps keep heat inside the cavity, stabilize temperature, and improve baking performance by sealing the gap between the door and oven frame.

• Forms the primary seal between the oven door and cavity to retain heat
• Reduces heat loss and temperature swings for more consistent cooking
• Helps prevent hot air and moisture from leaking around the door
• Common signs it's worn: visible tears or fraying, flattened spots, heat felt escaping, longer preheat or cook times

• Disconnect power and allow the oven to cool completely before servicing
• Remove the old gasket from the retainer channel or clips; clean the groove
• Press the new gasket evenly into place without stretching; ensure corners are fully seated
• Close the door and check for uniform contact around the perimeter; adjust as needed

This heat-resistant fiberglass oven door gasket seals the oven cavity perimeter, helping keep heat inside for consistent temperatures and efficient cooking. Replace a worn, frayed, or flattened seal to restore proper door sealing performance. What it does

• Forms a heat-resistant seal around the oven opening to minimize heat loss
• Helps maintain set temperature and overall cooking performance
• Can help address long preheat times, uneven baking, and hot air leaking around the door
• Replace if the gasket is frayed, brittle, compressed, or falling out of its channel

• Includes: 1 fiberglass door gasket

• Disconnect power and allow the oven to cool completely before service
• Remove the old gasket from its mounting slots or clips; clean the channel of debris
• Install the new gasket without stretching; seat it evenly around the perimeter with ends routed as originally positioned
• Close the door and check for uniform contact all around; adjust seating if needed

This seal restores a tight barrier between two mating parts in your appliance to prevent leaks and contamination. Replacing a worn or cracked seal helps stop drips, drafts, and noise so the unit can run reliably.

• Forms a tight seal between components to contain fluids or air
• Helps prevent leaks, drips, condensation, or unwanted airflow at joints
• Maintains efficient performance and reduces noise or vibration from loose fits
• Common failure signs: visible cracks/flattening, moisture where parts meet, odors, or louder operation

• Disconnect power and shut off water before servicing
• Note the seal's orientation; remove the old seal and clean all mating surfaces
• Install without stretching; lightly moisten if specified by your service manual (avoid petroleum products unless directed)
• Reassemble and test for proper operation and any leaks

Color: Grey

This oven door gasket creates a tight, heat-resistant seal between the door and the oven frame. It keeps hot air inside, helps the oven reach and hold temperature, and protects nearby surfaces from escaping heat. What it does

• Seals the gap around the oven door to reduce heat loss
• Supports accurate temperatures and more even baking performance
• Replaces gaskets that are brittle, flattened, torn, or frayed
• Common symptoms: heat felt escaping around the door, longer preheat/cook times, temperature swings, visible damage to the gasket

• One door gasket

• Disconnect power at the breaker and allow the oven to cool completely
• Open the door and pull the old gasket straight out of its retaining holes/clips
• Start at the top center; press the new gasket's tabs into place without stretching, ensuring corners are fully seated
• Close the door to confirm uniform contact all the way around the seal

This inlet/outlet seal creates a watertight barrier where two water passages meet in your appliance. Replacing a worn seal helps stop leaks at the connection and maintains proper water flow and performance.

• Forms a tight seal at an inlet/outlet connection to prevent water leaks
• Helps maintain correct water flow and pressure through the system
• Common signs of failure: drips or pooling water near the unit, visible cracks, flattening, or deformation of the seal
• Can resolve recurring leaks after reassembly of water-line connections

• Disconnect power and shut off the water supply before servicing
• Access the connection point and note the seal's orientation
• Clean mating surfaces; seat the new seal evenly without twisting
• Reassemble, restore water/power, and check carefully for leaks during a test run

This door gasket is the replacement seal that fits around an oven door to help contain heat and maintain cooking temperature. Replacing a worn gasket improves oven efficiency and reduces heat loss for more consistent results. What it does

• Seals the oven door to retain heat and maintain set temperatures.
• Helps prevent heat and smoke from escaping during use.
• Can reduce uneven cooking and long cook times caused by leaks.
• Helps limit high exterior temperatures around the door area.

What's included One door gasket. Install notes

• Disconnect power and allow the appliance to cool completely before starting work.
• Seat the gasket evenly into the door channel or retainer per OEM instructions; do not force or overstretch.
• Do not use adhesives unless the manufacturer specifies them; check door alignment and the seal after installation.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

Color: clear. It measures about 3-1/2 inches in diameter.

This replacement seal keeps liquids and food particles out of the blender motor housing to protect internal components and help prevent leaks. Fits the motor assembly where the shaft passes through the housing. What it does

• Seals the motor shaft opening to help prevent liquid from entering the motor housing.
• Reduces risk of motor damage or shorting caused by leaks into the base.
• Helps stop leaking at the blender base or around the blade assembly when worn.
• Replace if the seal is cracked, flattened, swollen, or shows visible wear.

• Always unplug the appliance before disassembly and removal of the jar or motor housing.
• Remove the blade and jar assembly per the service diagram to access the shaft seal; inspect mating surfaces and replace damaged components.
• Ensure the new seal is seated evenly around the shaft and in its groove; do not force or over-stretch the seal.
• After reassembly, run a short water test (with the unit unplugged from any direct water source) to check for leaks before normal use.

This refrigerator door gasket for foam-in-place doors creates a tight seal around the door opening to keep cold air in and moisture out, helping maintain stable temperatures and reduce frost and energy waste.

• Seals the door perimeter to prevent warm air leaks
• Helps maintain correct cooling performance and humidity levels
• Reduces frost and condensation caused by poor sealing
• Common signs it's needed: tears, warping, gaps, persistent frost/condensation, door not sealing or popping open

• Disconnect power before servicing
• Warm and relax the gasket in hot water or with a hair dryer on low to ease installation
• Remove the old gasket from the retainer/channel; install the new gasket starting at the corners and press fully into place
• Check the seal all around and adjust the door/hinges as needed; allow time for the gasket to set

This refrigerator door gasket seals the perimeter of the door to keep cold air in and warm air out. A fresh, flexible seal helps maintain temperature, reduce frost, and improve energy efficiency and food preservation.

• Creates an airtight seal between the door and cabinet
• Helps prevent temperature swings, frost buildup, and moisture around the door
• Can help with doors not sealing or cooling performance issues related to air leaks

• Unplug the appliance before service; remove food items from the door
• Warm the gasket with a hair dryer on low to relax shipping kinks; do not overheat
• Transfer/seat the gasket fully in the door channel; work evenly around corners
• After installation, close the door and check for uniform contact all around; adjust as needed

This mounting gasket creates a tight, cushioned seal where a component attaches to its housing or bracket. Replacing a worn seal helps stop leaks and rattles while restoring a secure, reliable connection at the mounting point.

• Forms a seal between two mounting surfaces to help prevent leaks or seepage
• Cushions and isolates vibration for quieter operation
• Helps maintain proper alignment of the mounted component
• Replace if the gasket is cracked, flattened, brittle, or no longer sealing

• Disconnect power and shut off water or gas, if applicable
• Note the gasket's orientation before removal
• Clean and dry both mating surfaces; remove all old gasket material and residue
• Seat the new gasket evenly; reassemble and tighten fasteners snugly without overcompressing; test for leaks/operation

Replacement gasket that restores a watertight seal at the factory connection to help prevent leaks and protect floors and cabinetry from water damage. Use to replace cracked, hardened, or torn seals. What it does:

• Seals mating surfaces to stop water leakage and reduce moisture-related damage.
• Common symptoms it helps address: visible leaks, pooled water under the appliance, or degraded/rubbery gasket material.
• Replaces worn, cracked, stiff, or torn seals to restore proper sealing performance.
• Seats into the original gasket groove—ensure the seal is fully seated with no gaps.

• Disconnect power and water supply before starting any service.
• Remove the old gasket, then clean and dry the mating surfaces and gasket groove.
• Press the new gasket into the groove evenly and inspect for full engagement around the perimeter.
• Restore power/water and run a short test cycle; check thoroughly for leaks before returning the appliance to regular use.