Maytag Pump

Ended up with replacement of the motor assembly. Read more

• Will not drain

I looked up the error code on the internet and determined that the drain pump had failed. I watched the Appliance Parts Pros repair video on how to replace this part, ordered a new pump and installed it myself in less than 30 minutes. This was an easy job that saved me the price of a service call, at least one hour of labor, and perhaps a markup on the part--probably around $200.00 total. I do this kind of work around the house a lot and win points with my wife. I still haven't received my... Read more

Installed new pump Read more

Its under warranty so I called Sears repair. The Technician determined the pump was bad order. After a month of waiting for Sears to order the part and the back and forth on the phone, I looked for the part myself. You guys sent the part and in 2 Days my washer is working again. No word yet, from Sears part order.. Read more

The hardest part was getting on my knees to do the repair/replacement. It was obvious debris wasn't being filtered out when the water was recirculated. I noticed the accumulator wasn't seating right and found the plastic clips on the backside were bent and worn. The new part came within a day and a half. Everything either unscrewed and snapped together with no tools. You may want to use a flat screwdriver to take the upper arm tube feed loose from its clips but it can be done by hand. Done... Read more

My dishwasher quit cleaning dishes and lost all pressure. The food screen would keep clogging up and I would have to take it out and clean it by hand. After putting a new impeller in, the "gears" on the impeller connected with the screen blades, the old impeller the "gears" were stripped off. And the new impeller comes with new seals, after taking old one out I noticed it wasn't long before my old seals would have started leaking. Very simple repair if you watch the great video that... Read more

• Will not drain
• Burning smell
• Noisy

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

I noticed when we would run washer water would stay in tub. Pump would hum but not pump water out. Layed washer on its belly . Pump was at bottom of washer. Easy access . Removed 3 screws,2 wires , & 2 hose clamps. Didn't have to call Maytag Repair man. Easy Read more

Replaced filter. It works great now, no more brown spots. Read more

Replaced sump, wash pump, drain pump, diverter motor, and thermostat. Read more

Replaced sump because the seal is not sold separately. You will need a skinny clamp after cutting the original swaged clamp off. Also Had to replace the cover as its seal is not sold separately either. Used dish soap on seals during assembly. Read more

• Will not drain

Took off cover, installed new parts. Read more

Removed and replaced diverter motor. Ops check good, no more leaking. I'm guessing the seal was the problem but diverter ruined (water residue) from leaking over the last 5 years??? This seal is only available if you buy the tub so followed another review - removed diverter then gently pried out the seal, cleaned and then lubed with silicone grease. Also turned the seal 180 degrees or the opposite way before reinstalling the diverter and then wrapping it all back under the counter. Read more

Replaced pump, found impeller on pump failed. Unfortunately had to replace entire pump, could not just buy impeller. Read more

Replaced pump Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more