Maytag Washer Parts

Fix slow filling or loud screaming noises during wash cycles. This water inlet valve controls flow into your washer tub. Moderate DIY repair.

This is a decorative trim bezel that surrounds the lid lock mechanism on a top-load washing machine, finished in chrome shadow. It snaps into place around the lid lock area to provide a clean, finished appearance. Replace this bezel if it is cracked, discolored, or broken, which can also affect proper lid lock alignment.

This lower wire harness routes power and signals between the control and the components beneath the tub on select 4.7/4.8-cu ft top-load washers. Replacing a damaged harness restores reliable connections and helps resolve intermittent motor or pump operation. What it does:

• Distributes power and control signals to lower-cabinet components
• Supports proper operation of the drive motor, drain pump, and related parts
• Typical symptoms: no spin or agitate, won't drain, intermittent operation, or visible heat damage/corroded connectors
• Match by part number for correct fit on 4.7/4.8-cu ft platform models

• 1 lower wire harness assembly

• Disconnect power and water supply before servicing
• Access the underside per your model (tilt the washer or remove panels as required)
• Transfer one connector at a time; route along the factory path and secure with existing clips/ties away from moving parts and sharp edges
• After installation, run a diagnostic or test cycle to normal operation

The Coin Slide Interface is an OEM part for Whirlpool commercial washers. It is a component that allows users to insert coins or tokens to activate the machine and initiate the laundry cycle.

Causes of a faulty coin slide interface can include regular wear and tear, damage due to misuse or vandalism, or electrical component failure. These factors can result in issues such as coin rejection, incorrect coin counting, or the inability to start the machine using coins.

Symptoms of a Bad Part:

• Will not start
• Not washing properly
• Timer will not set

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Washer won't start or advance through cycles? A failed capacitor prevents proper motor startup. This part stores energy to boost the motor during operation.

Fix a leaking or broken dispenser drawer that won't release detergent or fabric softener properly. Direct replacement restores proper dispensing.

This water inlet valve controls the flow of hot and cold water into the washing machine tub during fill cycles. It contains solenoid-operated ports that open and close in response to signals from the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it shouldn't.

Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.

Plastic push-on pulley that mounts on the washer motor shaft to drive the belt. Replace if cracked, melted, worn, or no longer grips the shaft securely.

Fix cycles that won't advance or mixed-up wash settings with a new timer assembly. Moderately difficult repair taking 30-45 minutes with basic tools.

The Shock Absorber is an OEM part compatible with Whirlpool washing machines. It is a crucial component that helps reduce vibrations and dampens movement during the spin cycle. The shock absorber absorbs mechanical stresses to prevent the washer tub, suspension springs, and other components from wearing out prematurely.  

Causes of a bad shock absorber include wear and tear over time, cracks or breaks from heavy loads, or damage due to impact.  

Symptoms of a bad shock absorber include:

• Excessive shaking, vibration or noise during the wash and spin cycles   
• The washer walking or moving during operation
• Premature failure of other suspension parts like springs or the washer frame
• Potential leaks if movement stresses plumbing connections

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Fix detergent not dispensing or drawer leaking issues with this washer dispenser drawer assembly. Holds detergent and fabric softener during wash cycles.

Supports and centers the spin basket and drive shaft for smooth, quiet rotation. Replace if washer makes loud roaring or jet engine sounds during spin.

This is an electric drain pump that removes water from the wash tub during the drain and spin cycles of a washing machine. It is typically mounted at the bottom of the washer and connects to the drain hose. Replace this pump if the washer fails to drain, drains very slowly, or makes loud humming or grinding noises during the drain cycle.

Mounts inside the washer drum to lift and tumble laundry evenly. Replace if cracked, broken, loose, or missing to restore proper tumbling action.

The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

• Increased vibration or noise during the wash or spin cycle
• The washing machine wobbling or becoming unsteady
• Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order 22003428.