Range / Cooktop / Oven Heating Element

This replacement part is a unit broil assembly, and it is intended for use in different types of ranges or ovens. This is a genuine replacement part made by General Electric. This unit broil assembly is typically found inside an oven or range and is part of the heating mechanisms that allow food to heat or cook. The broiler heats from the top of the appliance and helps with specific things like melting cheese.A new unit broil assembly might be needed if the user notices that the current one is not heating up properly. If the broil element is working the user should feel coming from the broiler area. It is also common to see the broil element turn bright red during use, indicating that there is heat coming off the element. If the element is completely attached but still unable to heat, it might be time to replace this part. Be sure that the appliance is powered off before replacing this part.This part is sourced directly from the manufacturer and is sold individually. This until broil assembly is an OEM replacement part.

Replace a failed surface heating element to restore reliable, even heat on your electric cooktop or range. This 3200-watt element helps get that cooking zone working properly again.

• Generates heat for the selected surface burner when turned on
• Works with the control to reach and maintain the set cooking temperature
• Useful when the old element shows visible breaks or burn marks

• Disconnect power at the breaker/fuse box and allow the cooktop to cool completely
• Access the element beneath the cooktop top panel per your model's procedure
• Label/photograph wire locations; transfer wires and any mounting hardware from the old element
• Handle the element and glass surface carefully to prevent damage

The Element-Surf is an OEM part for Whirlpool electric ranges. The element-surface performs a role in safe, even heating.

Causes of a worn or damaged element-surface can include scratches, cracks or chips from cookware use over time. Surface level issues compromise effectiveness.

Symptoms of a damaged element-surface include:

• Uneven or slow heating between elements
• Exposure of electrical components below
• Food debris easily getting lodged in irregularities
• Loss of the glossy smooth appearance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 8-inch surface burner element is the plug-in coil used on many electric ranges. Replacing a worn or failed element restores reliable heating and more even cooking performance on your stovetop.

• Provides heat to pots and pans when energized by the surface control
• Common fix for an element that won't heat or only heats partially
• Addresses visible coil damage such as breaks, blisters, or burned spots
• Corrects intermittent heating caused by an open or failing element

• Disconnect power to the range/unplug before servicing and ensure the element is cool
• Lift the old coil slightly, then pull straight out from the receptacle
• Inspect the receptacle/terminal block and drip bowl; replace if overheated or damaged
• Fully insert the new element terminals into the receptacle, seat the coil level, and test

This 6-inch surface element restores steady, even heat to the small burner on your electric range. Replace a burned-out coil to get back to reliable boiling, simmering, and everyday cooking performance.

• Converts electrical power into heat at the 6-inch burner position
• Helps when the small surface burner won't heat or heats unevenly
• Common signs include visible hot spots, blistering, or burned/loose terminals
• Seats in the drip bowl and connects to the proper surface element receptacle

• Disconnect power at the breaker or unplug the range; allow the element to cool before servicing
• Lift the old element from the drip bowl and pull straight out from the receptacle; avoid twisting or bending the coil
• Inspect the element receptacle for heat damage; replace the receptacle if contacts are burned or loose
• Fully seat the new element and ensure it sits level in the drip bowl before use

The broil element is the oven's upper heating element that delivers direct radiant heat for broiling and finishing foods. Replacing a failed element restores consistent top-side browning and proper broil performance.

• Provides high, direct heat from the top of the oven during the Broil cycle
• Restores broil function when the original element is open or damaged
• Common symptoms: no heat on Broil, weak/uneven top browning, element won't glow, visible breaks or blistering
• Matches the original design for proper fit and heat output on applicable models

• Disconnect power at the breaker or unplug the range; allow the oven to cool completely
• Remove oven racks to access the element
• Take out the element's mounting screws, gently pull the element forward, and transfer the wires one at a time to the new element
• Ensure terminals are fully seated and mounting screws are snug; restore power and test Broil

This broil element mounts at the top of the oven cavity and provides high, radiant heat for broiling and top-browning. Replace it if the broiler won't heat, heats unevenly, or the element shows visible damage.

• Delivers intense, top-down radiant heat for broiling and finishing dishes
• Restores broil performance when the original element is open, shorted, or weak
• Common symptoms: no broil heat, only part of the element glows, uneven browning, visible blisters/cracks, tripping the breaker
• Direct replacement designed to fit and connect to existing terminals

• Disconnect power at the breaker or unplug the range before servicing; high-voltage hazard
• Remove oven racks; take out element mounting screws and carefully pull the element forward to access terminals
• Transfer wires one at a time and support them to prevent retracting into the insulation; ensure tight, clean connections
• Reinstall screws, restore power, and test broil for an even, consistent glow

This surface heating element restores dependable heat to a burner on your range or cooktop. Also called a surface burner or top burner element, it delivers the cooking temperature for that zone when the control sends power. What it does:

• Generates heat for one cooking zone on the cooktop
• Common symptoms: burner won't heat, heats unevenly or only partway, takes too long to heat, or shows visible damage
• Helps isolate a single-burner failure when other surface elements still work
• Replaces a damaged or open element to restore consistent heating

• 1 surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Access the element per your model (remove burner pan or lift the glass top)
• Note/photograph wiring and transfer any brackets or clips; move wires one at a time to matching terminals
• Ensure the element sits flat and all connections are secure before reassembly and testing

This large surface element restores consistent heat to a cooktop burner on electric ranges and cooktops. Replace a failed element to bring back reliable heating performance when a burner no longer warms or heats unevenly.

• Supplies heat to a single surface cooking zone
• Common fix for a burner that won't heat or heats intermittently
• Can address uneven temperatures or hot spots on that burner
• Replace if the element is visibly damaged or fails a continuity test

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the unit to cool completely; access method varies by model
• Note/photograph wire positions and transfer them to the new element
• Ensure the element sits flat and centered; test all burner settings after reassembly

This upper broil element sits at the top of the oven cavity to provide intense radiant heat for broiling and finishing. Replacing a burned-out element can restore top-heat performance and consistent, even results.

• Provides direct, high heat from the top during Broil to sear and brown food
• Common symptoms include: no broil heat, uneven top browning, only the bake element heats, visible cracks/blisters, or tripping a breaker from a shorted element
• Works with the oven control to cycle heat and maintain broil temperature
• A failed element typically shows no continuity when tested with a multimeter

• Disconnect power at the circuit breaker and allow the oven to cool completely
• Remove racks; support the element, remove mounting screws, and carefully pull it forward
• Transfer wires one at a time with insulated pliers; prevent leads from slipping back into the insulation
• Avoid bending the element or over-tightening screws; ensure terminals are fully seated, restore power, and test Broil

This radiant surface element mounts beneath the glass cooktop to heat a surface burner. Replace it when a burner won't heat or heats intermittently to restore normal, consistent cooking performance.

• Generates radiant heat under the glass-ceramic top for a surface burner
• Cycles on and off to help maintain the set temperature
• Typical failure signs: no heat, intermittent heat, or visible damage to the element/terminals
• Used on electric ranges and glass cooktops

• Disconnect power at the breaker and allow the cooktop to cool fully before service
• Lift/hinge the glass top and support it to avoid stress or cracks
• Note wire positions; transfer any mounting clips/brackets from the old element to the new
• Ensure the element sits level under the glass and all connections are secure before reassembly

This dual surface element restores steady, selectable heat to a cooking zone on your electric range or cooktop. It provides two heating areas in one burner position so you can match heat output to small or larger cookware.

• Heats cookware by energizing the inner ring alone or both inner and outer rings together
• Helps resolve issues such as a surface burner not heating, only one ring heating, or intermittent/uneven heat
• Replaces a cracked, blistered, or visibly damaged element to restore reliable performance

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element from beneath the cooktop; photograph wire locations for reference
• Carefully transfer any brackets, clips, or attached limiter from the original element if required
• Avoid touching the element surface; secure all connections and test both inner and dual settings after reassembly

This replacement bake element restores the lower oven heat in electric ranges/ovens. It brings back proper preheating and even baking performance when the original element is burned out or physically damaged. What it does:

• Provides the primary heat from the bottom of the oven during Bake cycles
• Common signs of failure: no heat in Bake, very long preheat times, uneven baking, or visible blisters/cracks on the element
• If Broil still works but Bake does not, the bake element is a likely failure point
• Located at the bottom of the oven cavity to deliver even, consistent heat

• 1 bake element

• Disconnect power at the breaker and let the oven cool completely before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward
• Transfer the two wires to the new element, keeping them from slipping back into the oven cavity
• Reinstall the element and screws, restore power, and test Bake

• With power disconnected, check the element for continuity; an open circuit typically indicates a failed element

The Range Dual Radiant Heating Element is designed to provide reliable and efficient heating for your Samsung range. Crafted as a genuine OEM part, this heating element ensures seamless compatibility and optimal performance with your appliance. Featuring a dual radiant design, it delivers consistent and even heat distribution, allowing you to cook your meals perfectly every time. The durable construction of the Range Dual Radiant Heating Element guarantees long-lasting use, reducing the need for frequent replacements and saving you time and money. Installation is straightforward, making it an ideal choice for DIY repairs without compromising on quality. By choosing this genuine OEM part, you can restore your rangeGÇÖs functionality with confidence, ensuring that your kitchen operates smoothly and efficiently. Enhance your cooking experience with a component that offers both reliability and superior performance, tailored specifically for Samsung ranges.

This electric surface element replaces a failed top burner on your range or cooktop. Installing a new element restores dependable, even heat and responsive temperature control when a burner won't heat or behaves inconsistently.

• Provides the heat for the selected cooking zone when the surface control sends power
• Common signs of failure: burner does not heat, heats intermittently or unevenly, visible burn spots/cracks, or an open reading on a continuity test
• A shorted element may trip the breaker or spark when that burner is turned on

• Disconnect power at the breaker or unplug the appliance before servicing; allow the cooktop to cool completely
• Access the element per your model's service manual; support any glass surface to avoid stress cracks
• Note wire positions and transfer connections one at a time; reuse original mounts and hardware
• Ensure the element sits level and secure before reassembly and testing

Restore dependable heat to your indoor grill module with this electric grill element. Replacing a worn or failed element brings back even cooking and consistent searing performance on compatible grill cartridges. What it does:

• Converts electrical power into radiant heat for indoor grilling
• Delivers even heat distribution across the grill area when functioning properly
• Common fix when the grill won't heat, heats slowly, or has cold spots
• Replace if the coil is cracked, blistered, or visibly damaged

• 1 electric grill heating element

• Disconnect power at the breaker or unplug the unit; allow all components to cool completely
• Remove grill grates and any shields or pans to access the element
• Lift the element straight up to disengage from the terminal block; avoid bending terminals and transfer any reusable clips/brackets if present
• Seat the new element fully in the terminals; verify secure connections before reassembly and testing