Kenmore Elite Parts

The repair kit has everything needed for both sides of the rack but there were no instructions so it took me some time to figure out how it all mounted on the basket. The original design was totally different than the repair kit so it would have been very beneficial to have at least a diagram that showed how everything fit together. That being said, once I figured out how all the parts fit, then it was a very easy repair. You won't reuse any of the old parts except for the end caps that snap... Read more

• Will not drain
• Noisy

It was fairly obvious that the washer drainer motor had failed, water was not draining, filter was clean (bottom lower left panel door, have a pail ready!) and drain line was not blocked. Someone had provided great advice on the Appliance Parts Pro's site about replacing the drain motor from the bottom. Great suggestion! Easy to do, although be prepared for more water to drain from the washing machine onto the floor after you lay it over. I carefully lowered the machine onto it's back,... Read more

I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more

My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more

• No heat or not enough heat
• Won't start

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

The original issue with the dryer is that a corner of the lint screen was sticking out of the lint screen guide, and it would not stay flush with the guide. As a result, many tank top straps, waistband strings, and blankets would get caught on this corner and twist, tear, or warp my clothes. When I did my research on the issue, I kept reading that it was an issue with the lint screen that came with the dryer. So I ordered the lint screen, guide, and cover that appliance part pros recommends to... Read more

Installed 2 new dishrack roller assemblies. The only tools I needed were my fingers, snapped the old assemblies out and snapped the assemblies in. Read more

• Will not stop filling with water
• Leaking
• Shuts off too soon
• Will not fill with water

Replaced the cold water valve unit (has 4 ports and 1 inlet) which is very straight forward; requires : 1 phillips screwdriver ~#2 1 needlenose plier, medium size 1 channel lock plier, medium size 1 marker pen 1 - cold water valve assembly # AP4445613 1 - hot water valve assembly #AP4441935 1 - water level pressure switch #AP4440713 an old towel or two for absorbing small amounts of water a cellphone / camera for making sure you have the... Read more

I replaced the warped cover guide and the lint filter. Now it works perfect! Sears was going to charge $100 just to diagnose the well known problem, not including parts and labor. It only requires 4 screws(i used the old ones). Easy fix. Read more

My Kenmore 790.74139310 gas range was taking over 30 minutes to reach 350F. It used to take a little less than 10 minutes. The problem was the ignitor for the lower gas burner. It would glow but not pass sufficient current to increase the gas flow to the lower burner. Once at temperature, there is of course loss of heat when loading the oven with room temperature food. This took too long to recover, so we did not have proper temperature for proper cooking for the first 30 to 40 minutes. Food... Read more

1. I unplugged the washer from outlet 2. I turned off the hot and cold water taps going to the washer (both just in case) 3. Draped a towel over back edge of washer and under where hoses coming from water outlets attach to back of washer (to catch any loose water out of the hose or screw nozzle leading to valve assembly, then unscrew (by hand) the cold water hose from back of washer (leave hot water hose alone as not needed). 4. Unscrew valve assembly from washer by two screws on back top of... Read more

My Whirlpool dishwasher was leaking out the bottom of the door. I replaced the gasket and the lower door seal. When I ran a test wash, it was still leaking. After reading more online, I found that it could be a cracked washer arm. The initial inspection of the washer arm looked normal but when I used my faucet to slowly pour water into the inlet of the arm, I noted that water was leaking through a seam and not just the holes where it should come out. I then tried running a wash without the... Read more

In 2012 I purchased an LG French door bottom freezer fridge. this thing was a problem from day one, I had to call 3 technicians where I bought it from- a nameless major retailer. through the 2 1/2 years I have had it, the problems were always with the ice cube maker, and finally, the motor finally stalled. I was able to revive it, but only for a short time- then I went to replace the unit all together and searched high and low until I came across Appliance Pros. I actually had no idea that 2 of... Read more

• Noisy
• Door won't close
• Door latch failure

I finally decided to repair my dishwasher because the door would free fall to the floor possibly breaking the hinges. Also the top shelf was rolling out on its own every time the door was opened. I first pulled the dishwasher out of the enclosure and found that the drain hose was directly under the pump area throwing the unit completely out of level. Also the inadequate plastic and rope counterbalance on the left side was completely broken where the rope was attached to the plastic piece to the... Read more