Spray Arm & Related

This connecting ring nut secures a threaded water-path connection inside the dishwasher, helping keep the joint tight and leak-resistant. Replace a cracked, stripped, or missing nut to restore a secure fit and reliable operation.

• Tightens and holds a mating connector, tube, or manifold in place
• Helps maintain a watertight connection when used with the proper seal
• Replaces worn or cross-threaded hardware that can cause leaks or loose joints
• Typical symptoms include dripping at the connection, a loose hose/manifold, or difficulty keeping the fitting tight

• Disconnect power and shut off the water supply before servicing
• Access the joint; start threads by hand to avoid cross-threading, then snug with the proper tool—do not overtighten
• Inspect any O-ring or gasket at the connection and replace if worn
• Restore water and check for leaks before reassembling panels

This sprinkler nozzle directs wash water into a focused spray inside the dishwasher for effective coverage. Replacing a clogged or damaged nozzle restores proper spray pattern and helps improve cleaning results, especially on the upper rack.

• Channels water through the sprinkler assembly for targeted spray coverage
• Maintains the correct spray pattern and pressure for thorough washing
• Replace if clogged with mineral deposits, cracked, loose, or missing
• Symptoms can include poor cleaning, weak/uneven spray, or the upper rack not getting clean

• Disconnect power and water supply before servicing; allow the tub to cool
• Pull out the rack to access the sprinkler area; remove the old nozzle (snap or twist fit varies by model)
• Clean mating surfaces and install the new nozzle securely, ensuring proper alignment
• Run a short test cycle to verify normal spray operation

This middle spray arm assembly mounts at the center wash level and distributes pressurized water across both racks. Replacing a damaged or clogged arm restores even spray coverage and helps resolve weak cleaning performance, especially on the upper rack.

• Directs and disperses wash water from the mid-level for thorough coverage
• Rotates to spray dishes on both racks when unobstructed
• Helps when dishes come out dirty, the top rack isn't getting clean, or the arm is cracked/clogged
• Restores proper spray pattern and circulation

• Disconnect power and water supply before servicing the dishwasher
• Open the dishwasher; remove the upper rack if needed. Release the retainer and pull the old mid-level arm off its hub/tube
• Align and press the new arm onto the hub until secure; it spins freely
• Run a test cycle to normal spray and rotation

This upper wash arm directs rotating spray to the dishwasher's top rack to help improve cleaning coverage and reduce food/residue on upper-rack dishes. Fits as the rotating upper spray arm assembly for compatible dishwashers. What it does:

• Rotates and sprays water across the upper rack to help remove stuck-on food and rinse dishes.
• Helps correct weak or uneven spray patterns from the top rack.
• Can reduce spotting and areas that remain soiled when the upper arm is damaged or clogged.
• Replaces a worn, cracked, or clogged upper spray arm to restore proper spray action.

• Always disconnect power to the dishwasher and turn off the water supply before servicing.
• Remove the upper rack to access the arm; unclip or unscrew the old arm and install the replacement until it seats/threads securely.
• Clear any debris from the mounting area and ensure the arm spins freely before running a test cycle.
• Run a short rinse or quick cycle to verify correct spray pattern and fit.

This lower dishwasher spray arm circulates water across the lower rack to help wash and rinse dishes effectively. Replaces a worn or damaged arm to restore proper spray coverage and improve cleaning performance. What it does:

• Rotates and distributes pressurized water to reach dishes on the lower rack
• Helps remove food soil and rinse detergent from dishes and cookware
• Commonly replaced when you notice poor cleaning, uneven spray, or a cracked/broken arm
• Also replaced if the arm no longer spins freely or leaks at the hub

• Disconnect power to the dishwasher and shut off water supply before starting
• Remove lower rack and any obstructions; follow OEM removal steps to detach the old arm
• Ensure the arm hub and spray ports are free of debris before installing the new arm
• Reinstall rack, restore power/water, and run a short cycle to confirm proper rotation and no leaks

This lower spray arm distributes pressurized water across the dishwasher's lower rack to help remove food and residue for cleaner dishes. It mounts on the hub beneath the lower rack and spins during the wash cycle. What it does:

• Directs rotating spray patterns to reach plates, pots and pans on the lower rack
• Helps clear stuck-on food and improve overall wash performance when functioning properly
• Can fail or clog from mineral deposits or trapped debris, causing reduced spray or poor cleaning
• Replacing a worn or cracked spray arm restores proper water flow and spray coverage

• Disconnect power and water to the dishwasher before starting any service
• Inspect the hub and fastener for damage; remove debris from spray holes and seals before installing
• Hand-thread or snap the arm into place per factory alignment; do not force or overtighten
• Run a short rinse cycle to check for proper rotation and leaks after installation

This is a replacement hex nut used to secure appliance components and fasteners. It restores proper fastening where a stripped, missing, or damaged nut causes loose or rattling parts. What it does

• Secures mating bolts or threaded studs to hold panels, brackets, or assemblies in place
• Stops vibration-related loosening that can cause rattling or misalignment
• Replaces corroded, stripped, or missing nuts to restore a safe connection
• Works wherever the OEM specifies this nut for fastening duties

• One replacement hex nut

• Disconnect power (and water, if applicable) to the appliance before servicing
• Use the correct size wrench or socket to avoid rounding the nut
• Tighten snugly but avoid overtightening; replace if threads are damaged

This mid spray arm assembly delivers targeted spray to the dishwasher's middle rack so dishes get an even clean. Replaces a cracked, broken or clogged mid-arm to restore proper water distribution and cleaning performance. What it does

• Directs pressurized wash water across the middle rack for effective cleaning.
• Rotates to evenly distribute water; replaces arms that no longer spin freely.
• Fixes issues where dishes on the middle rack come out dirty or spotting occurs.
• Replaces arms that are cracked, leaking, or clogged with mineral deposits.

• Disconnect power and water supply before beginning any repair.
• Remove the middle rack to access the spray arm.
• Press or fasten the arm into place until secure; verify it spins freely before running a cycle.

This upper spray arm assembly delivers a rotating spray pattern to distribute water across the upper rack, restoring proper wash coverage and improving cleaning performance for dishes and glassware. What it does:

• Replaces the upper spray arm to restore rotating water spray across the top rack
• Helps resolve poor cleaning or missed spots on upper-rack items
• Restores proper water distribution when spray arm is cracked, clogged, or not spinning
• Works with the dishwasher's spray system to reach hard-to-clean areas

• One upper spray arm assembly

• Turn off power and water supply before starting any repair
• Remove the upper rack to access the spray arm; follow OEM instructions for removal/replacement
• Inspect and clear any debris from the spray holes and mounting area before re-installing

This arm mounts below upper dishrack.

This mounting nut secures the tower heater assembly in the appliance, keeping the heater stable and properly positioned for safe, efficient operation. Replacing a damaged nut restores secure attachment and reduces rattling or loose components. What it does

• Secures the tower heater assembly to the appliance chassis or mounting bracket
• Helps maintain proper heater alignment for reliable heating performance
• Prevents movement that can cause noise, intermittent contacts, or wear on connections
• Used when the original nut is stripped, corroded, or missing

• One tower heater assembly mounting nut

• Disconnect power to the appliance before attempting any repair
• Use appropriate hand tools; avoid over-tightening which can strip threads or damage the heater assembly

This snap-in outlet connector secures wiring to an appliance control or harness and restores a reliable electrical contact. Designed for a direct, tool-assisted snap fit, it helps eliminate loose or intermittent connections. What it does:

• Provides a secure snap-in electrical connection between wiring and the appliance harness or control
• Restores power flow when a worn or damaged outlet causes intermittent operation or no power
• Prevents arcing and poor contact that can result from loose terminals
• Matches OEM fit for straightforward replacement when the original snap outlet is broken or missing

• Disconnect power to the appliance before inspecting or replacing electrical parts
• Remove access panels as required to reach the outlet; replacement typically snaps into place
• Verify correct orientation and full seating of the connector to ensure a solid contact
• If corrosion or wiring damage is present, replace or repair wiring per OEM guidance