Washer Clip Or Clamp

This retaining clip secures small panels and components to help keep assemblies aligned and reduce rattles or movement during operation. It's a simple replacement that restores proper fit where the original clip has broken or gone missing. What it does:

• Holds trim, panels or small assemblies in place to prevent loosening and vibration
• Restores proper alignment and fit where a worn or broken clip causes gaps or rattling
• Commonly used where snap-in retention is required for plastic or sheet-metal parts
• Simple, single-piece part with no electrical or mechanical adjustments needed

• One retaining clip

• Turn power off and unplug the appliance before accessing the repair area
• Remove any adjoining panels or fasteners as needed to access the clip location
• Press or snap the clip into the mating slot; use care to avoid bending surrounding parts

This clamp secures flexible hoses or tubing to fittings to help stop leaks and keep connections tight. It's a small but essential fastener for water and drain lines in many appliances. What it does:

• Holds hose or tube to a barb, spud, or fitting to maintain a watertight seal
• Prevents leaks that can cause puddling, dripping, or appliance shutdowns
• Replaces worn, corroded, or broken clamps that no longer tighten properly
• Helps maintain proper hose positioning to avoid kinks or stress on connections

• Disconnect power and shut off water supply before servicing appliances.
• Use the appropriate pliers or clamp tool to remove and re-seat the clamp without damaging the hose.
• Inspect hose ends and fittings; replace hoses that are cracked or severely worn.
• After installation, restore water and power, then run a short cycle and check for leaks.

This spring clamp secures the refrigerator door bellow to the cabinet, helping hold the bellow in place for a tighter seal and consistent door alignment. A simple replacement that restores proper bellow retention. What it does

• Holds the door bellow tightly to the cabinet or door frame
• Prevents bellow from pulling away or bunching during door use
• Helps maintain a consistent seal to reduce drafts at the door edge
• Works where a worn or damaged clamp allows visible gap or misalignment

• Basic hand tools usually required; inspect surrounding bellow for wear before installing
• Wear gloves and eye protection; spring clamps can snap back during removal/installation
• If clamp is difficult to seat, ensure bellow is properly positioned and not torn
• Replace damaged bellows or additional fasteners to ensure a complete seal

A small replacement retainer clip used to secure interior trim or components so panels and shelves stay in place. Replacing a worn or broken clip restores a snug fit and reduces rattling or loose parts. What it does

• Holds trim, panels or small components in place to prevent shifting
• Prevents rattling and keeps parts aligned for proper operation
• Replaces cracked, broken or missing clips that allow parts to sag or fall
• Works wherever the OEM clip design is specified for a secure snap-fit

• Clip

• Disconnect power before servicing appliances with electrical components
• Remove surrounding trim or components carefully to access clip location
• Press or snap the clip into place; avoid forcing to prevent damage
• Keep small parts away from children and pets during installation

This clamp secures flexible hoses and small-diameter tubing to fittings, helping prevent leaks and keeping connections tight for reliable appliance operation. Use it where a compact, durable clamp is required for water or drain lines. What it does:

• Holds hoses or tubes firmly to inlet/outlet fittings to reduce leaks
• Prevents hoses from slipping off during normal use or vibration
• Helps maintain proper fluid flow by keeping connections sealed
• Useful for water lines, drain hoses, and small appliance tubing

• One clamp

• Turn off and unplug the appliance and shut off water supply before starting
• Inspect the hose and fitting; replace any damaged hose before installing clamp
• Position clamp over the hose/fitting and tighten evenly for a snug fit without crushing the hose

Red

This backsheel clip secures the appliance backsheet to the cabinet, keeping panels aligned and preventing gaps. It's a simple replacement that restores proper panel fit and reduces rattling or movement. What it does:

• Holds the backsheet or rear panel in place for a flush fit
• Stabilizes the cabinet to reduce vibration and noise
• Helps maintain proper airflow paths by keeping panels sealed
• Replaces damaged, broken, or missing mounting clips

• High-level, screwless snap-in or push-fit — remove power and access the rear panel before replacing
• Use a flashlight and small flat tool to pry the old clip free if brittle or stuck
• Wear gloves to protect hands from sharp sheet-metal edges
• If multiple clips are damaged, replace all affected clips for even panel alignment

A spring-style drain hose clamp that secures flexible drain tubing to fittings to prevent leaks and hose separation. Durable metal construction keeps drain connections tight for reliable wastewater flow and trouble-free operation. What it does:

• Holds drain hose firmly to pump, elbow or spud to reduce leaks and disconnections
• Applies even compressive force around flexible tubing for a secure seal
• Helps stop water spraying or pooling caused by a loose hose connection
• Commonly used on appliance drain and discharge lines where a snug clamp is required

• One spring-style drain hose clamp

• Use pliers to expand the clamp, fit over the hose, then release to engage; avoid twisting the hose while seating
• Replace any cracked or brittle hose before clamping to ensure a leak-free repair
• Disconnect power and water if required by your appliance before accessing the drain connection

This pressure hose clamp secures the small vacuum/pressure hose to its fitting, keeping the hose in place so the appliance can accurately sense water level and cycle pressure. Simple, direct replacement for a worn or loose clamp. What it does:

• Holds the pressure/vacuum hose snugly to prevent leaks or hose detachment
• Helps maintain proper pressure signal for correct cycle and fill operation
• Commonly used when a loose or damaged clamp causes intermittent pressure-related symptoms
• Small replacement part that restores a firm hose connection

• Disconnect power (and water, if applicable) before servicing the appliance
• Use a small screwdriver or pliers to remove the old clamp and secure the new clamp in place
• Ensure the hose is fully seated on the fitting before tightening the clamp