Washer Clip Or Clamp

To use with BOOT #wh8x246

This clamp assembly secures the washer's door boot (gasket) in its groove to maintain a watertight seal at the front of the tub. Replace a stretched, bent, or broken ring to stop leaks and keep the boot properly seated.

• Holds the door boot/gasket firmly to prevent front-panel water leaks
• Restores proper tension when the original ring is deformed or the spring fails
• Common symptoms: water leaking at the front, boot slipping off, visible broken or missing clamp
• Often replaced during door boot service to ensure an even, reliable seal

• Disconnect power and turn off water supply before servicing
• Carefully relieve tension and remove the old clamp without tearing the boot
• Install the new clamp evenly around the opening
• Run a short test cycle and check for leaks after reassembly

This clamp secures flexible hoses and small-diameter tubing to fittings, helping prevent leaks and maintain proper fluid flow in appliance systems. It's a simple replacement that restores a tight, reliable connection. What it does

• Holds a hose or tube firmly on a barb or nipple to stop leaks and loss of pressure
• Keeps water, drain, or vent hoses seated during normal appliance operation
• Replaces worn, corroded, or loose clamps that cause dripping or poor connections
• Works where a small, durable clamp is required for routing or securing tubing

• One hose clamp

• Inspect hose and fitting for damage; replace hose if cracked or hardened before installing the clamp
• Tighten clamp until snug—do not overtighten; ensure even compression around the hose
• Disconnect power and water as appropriate and take safety precautions before working on the appliance

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners

This clamp secures a flexible appliance hose to a fitting to help prevent leaks and keep connections tight. It's a small but essential part that restores a proper seal on water or drain lines. What it does:

• Holds a hose firmly to a tailpiece, barb or connector to reduce leaks and hose slippage
• Helps stop intermittent dripping or pooling caused by loose hose connections
• Restores a proper seal after hose replacement or maintenance
• Works on common appliance water/drain lines where this clamp style is used

• One hose clamp

• Disconnect power and shut off water to the appliance before starting any work
• Allow the appliance and hoses to cool if recently used; use gloves and eye protection
• Use appropriate pliers or a screwdriver (depending on clamp style) to remove and install the clamp; avoid over-tightening
• Inspect the hose and fitting for damage; replace the hose if cracked or worn

The washer Hose Retainer Holder Clip is an OEM part that mounts behind the control panel on LG front-loading washers. It positions water supply hoses to prevent kinks or stress that leads to leaks over time. 

Causes of a failed clip include fatigue from years of front-load vibration and damage from any installation or repair work behind the control panel.

Symptoms of an insufficient hose retainer clip include:

• Loose, misrouted, or flopping hoses behind the control panel
• Bulging or kinked hoses that restrict water flow
• Water leaks at hose connections

This OEM replacement clip is compatible with select Kenmore front-loaders.

This front panel hanger secures the appliance's front service panel to the cabinet, restoring proper alignment and preventing vibration or sag. It's a direct-fit replacement designed to bring panels back to factory position for a clean, stable appearance. What it does:

• Supports and anchors the front service panel to the appliance cabinet
• Keeps the panel aligned to prevent gaps, sagging, or rubbing
• Reduces rattles and vibration caused by a loose or damaged hanger
• Helps the panel latch securely for safe, normal operation

• One front panel hanger

• Disconnect power before beginning any service
• Partial panel removal is typically required; support the panel during replacement
• Inspect surrounding clips and fasteners; replace if worn to ensure a secure fit