Washer Door, Door Glass & Parts

This front door panel replaces the outer frame of the washer door, restoring appearance and proper alignment. It frames the window and interfaces with the handle/latch components so the door closes and latches as designed.

• Forms the exterior frame around the door glass and completes the door assembly
• Provides alignment for door components to help ensure smooth closing and latching
• Replaces cracked, broken, or discolored outer door trim/panel
• Can help resolve issues like loose-feeling doors or doors not aligning with the latch

• Disconnect power before servicing
• Open the door, support the assembly, and remove the perimeter screws securing the outer panel
• Transfer any components attached to the old panel, position the new panel, and tighten screws evenly
• Check door alignment and latch operation before returning the appliance to service

This replacement washer door window restores a clear view into the tub on compatible front-load models and helps the door seal correctly. Replace a cracked or cloudy pane to reduce leaks and keep operation safe. What it does:

• Provides the transparent viewing window in the washer door
• Works with the door boot/gasket to help form a watertight seal when closed
• Replace if the glass is cracked, chipped, shattered, or excessively scratched/cloudy
• Common symptoms include water leaking from the door area, poor sealing/door won't close, or visible damage to the window

• One door window glass

• Disconnect power and turn off water supply before servicing
• Wear cut-resistant gloves and eye protection; handle broken glass carefully
• Support or remove the door to a flat surface; separate door halves and transfer the window, noting orientation
• Clean the door boot sealing surface; seat the new glass evenly and reassemble without pinching the gasket; test for leaks

This gray rear door panel forms the inner half of the washer door assembly. Replacing a cracked or warped panel restores door integrity, supports the glass, and helps the door seal close and latch as designed. What it does:

• Serves as the inner structure of the washer door and mates with the outer frame
• Supports and positions the door glass and related trim
• Helps maintain proper seal between the door and tub boot to minimize leaks
• Common symptoms: cracked/broken panel, difficulty latching, door misalignment, leaks at door area

• 1 rear door panel in gray

• Disconnect power and turn off water supply before servicing
• Remove the door from the hinge, then separate the door halves by removing perimeter screws/clips
• Transfer the door glass and any reusable hardware/trim to the new panel; keep orientation consistent
• Inspect the door boot lip and ensure it seats properly; verify smooth closing and latching before use

Color: Pewter

Plastic door cover

Inner door panel kit restores the refrigerator door interior, covering the cavity and providing mounting surfaces for bins and gaskets. Replacing a cracked or warped inner panel improves appearance and helps ensure door components fit correctly. What it does:

• Replaces a damaged, cracked, or warped inner door panel to restore the door's interior surface.
• Provides mounting surface for door bins, shelves and the door gasket so components sit securely.
• Helps cover and protect insulation and internal door wiring or components from damage.
• Common symptom fix: visible cracks, deep stains, loose door bins, or a warped liner that prevents proper gasket seating.

• Disconnect power to the appliance and remove food and loose items from the door before starting.
• Some disassembly of the door liner may be required; retain any fasteners, clips, and trim for reuse.
• Avoid damaging insulation, wiring, or the door gasket while removing and installing the panel.

The Washer Door Safety Lock is an essential component designed to ensure the safe and secure operation of your Samsung washer. This genuine OEM part provides reliable locking functionality, preventing the washer door from opening during the wash cycle. Crafted with precision, the outer door window not only enhances the safety features of your appliance but also maintains its original aesthetic appeal. Easy to install, this safety lock ensures a snug fit with compatible Samsung washer models, restoring your appliance's functionality to its optimal state. By replacing a faulty or damaged Washer Door Safety Lock with this genuine OEM part, you can enjoy peace of mind knowing your washer operates securely and efficiently. Investing in this high-quality component helps extend the lifespan of your Samsung washer and maintains a safe laundry environment for your home.

This ring fits into its mating groove to retain or space a component within an assembly. It keeps parts aligned and secure so your appliance operates reliably under vibration and everyday use.

• Provides axial retention or spacing within the assembly
• Helps prevent parts from backing off or shifting during operation
• Common replacement when the original ring is bent, cracked, or missing
• Symptoms include looseness, rattling, or components not staying in place

• Disconnect power; shut off water if working on a water-carrying assembly
• Note the ring's orientation and groove location before removal
• Use the appropriate pliers or hand tools; avoid prying against delicate parts
• Ensure the ring is fully seated in its groove before reassembly and testing

This replacement vent manages internal airflow within your appliance, routing air through the intended path. Restoring a damaged or missing vent helps maintain performance and reduces heat and moisture buildup inside the cabinet. What it does:

• Directs and regulates airflow through the appliance's air path
• Helps maintain proper pressure balance and efficient moisture removal
• Reduces the chance of lint or debris bypassing the intended ducting
• A cracked, warped, missing, or clogged vent can contribute to weak airflow, longer cycles, excess heat, or unusual noises

• 1 vent

• Disconnect power before servicing; allow hot components to cool
• Access the vent by removing the appropriate panel; note screw and clip locations
• Transfer any mounting hardware or seals from the old vent and ensure proper orientation
• Clear lint/debris from adjoining ducts before reassembly; test run to ensure smooth airflow and no rattling

The Washer Door Glass is an OEM part for GE washers. This glass serves as a protective barrier while allowing you to observe the washing process inside the machine. The door glass is designed to withstand the rigors of regular use and maintain transparency for a clear view of your laundry.

A bad door glass can occur due to accidental breakage or cracks over time. If you notice signs of damage, such as shattered or missing pieces, it may be time to replace the door glass.

Symptoms of a bad door glass include:

• Shattered or broken glass
• Visible cracks or chips
• Inability to see through the glass

Restore the function of your GE washer by replacing the damaged door glass with this genuine part. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This replacement door glass forms the clear window in the door of select front-load units, restoring safe visibility and proper door fit. Replace a cracked, chipped, or shattered pane to prevent leaks and ensure the door seals and latches correctly. What it does

• Creates the viewing window in the door and mates to the door gasket/boot
• Helps maintain a proper seal to contain wash action
• Restores safe operation when the original glass is damaged
• Common symptoms: visible cracks or shattering, water leaking from the door area, door not closing flush, rattling glass

• 1 door glass pane

• Disconnect power and turn off water supply before service
• Wear cut-resistant gloves and eye protection; handle glass carefully
• Remove the door, set it on a padded surface, and transfer trim/gasket as designed
• Tighten fasteners evenly and check gasket alignment to prevent leaks

This inner door frame is the interior support trim that helps secure the door assembly and provides a finished surface inside the appliance door. It restores proper fit and a clean appearance when the original frame is cracked or damaged. What it does:

• Provides structural support for the inner door panel and helps hold components and liners in place
• Restores proper alignment so the door closes evenly and seals correctly
• Replaces cracked, warped, or broken frame sections that can allow rattling or gaps
• Helps maintain the correct interface between the door and the gasket to prevent airflow issues

• Disconnect power to the appliance before beginning any repairs.
• Removal typically requires taking off the door trim or liner and using basic hand tools; keep fasteners organized.
• Handle the frame and door panels carefully to avoid scratching or bending other surfaces.

This replacement door transition ring restores the trim and alignment where the appliance door meets the cabinet, helping the door close smoothly and improving the unit's appearance and seal. What it does

• Covers and protects the gap between the door and cabinet, preventing rubbing and wear on edges.
• Guides the door for consistent closing and helps reduce drafts or uneven sealing.
• Stops rattling or banging caused by worn or damaged trim pieces.
• Restores finished look to the door area when the original ring is cracked, broken, or missing.

• One door transition ring.

• Disconnect power (or unplug unit) before starting any work to avoid electrical or injury hazards.
• Most installs are snap-in or require removing the door or outer panel—use basic hand tools and avoid forcing parts.
• Handle the trim carefully to avoid cracking; replace any damaged fasteners or clips rather than reusing broken pieces.

The Lid is an OEM part for Whirlpool washing machines. As the primary cover on top of the washer tub, the lid protects interior components while also serving an important functional purpose. During the wash cycle, the lid assists in retaining water and generating agitation within the tub to thoroughly clean clothes. 

Causes of a faulty lid can include warping, cracks, or breaks in the material over extended use. Prolonged exposure to moisture and chemicals may degrade its structural integrity.

Symptoms of a bad lid include:

• Inability to fully latch or seal closed 
• Loss of water retention ability during cycles
• Excessive leaks or standing water outside the tub
• Reduced agitation levels for inefficient cleaning

This is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and Admiral models.
 

The Lid is an OEM part for Whirlpool washers. It covers and secures the washing machine drum during operation, ensuring safe and efficient washing.

A bad washer lid can be caused by regular use, accidental damage, or wear and tear over time. If you notice issues such as a loose or broken lid, difficulty in closing or latching the lid, or if the lid is not staying securely in place during the wash cycle, it may indicate a problem with the washer lid.

Symptoms of a bad washer lid include:

• Lid not closing or latching properly
• Excessive vibration or movement during the wash cycle
• Water leaking from the top of the washer

Replace your faulty washer lid with this genuine OEM part to restore your washing machine. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This inner oven door window provides the clear, heat-resistant viewing panel that lets you monitor cooking without opening the door. Replacing damaged or cloudy glass restores safe visibility and helps maintain oven temperature. What it does:

• Serves as the interior viewing glass for the oven door
• Keeps heat contained while allowing you to see inside the oven cavity
• Commonly replaced for cracks, chips, fogging, or shattered glass
• Helps reduce heat loss from a damaged or broken door panel

• One inner oven door window

• Disconnect power to the appliance before starting any repair
• Allow the oven and door to cool completely; wear cut-resistant gloves and eye protection when handling glass
• Removal may require partially disassembling the oven door and carefully detaching retaining clips or screws