Washer Dryer Combo Wire, Harness, Power Cord

This wire harness assembly routes power and signals between controls and components to restore electrical connection and appliance function. It replaces a damaged or worn harness to help recover intermittent or lost circuits. What it does:

• Carries power and control signals between console, motor, sensors and other appliance components
• Restores connectivity when wires are frayed, pinched or connectors are corroded
• Can stop intermittent operation, no-power conditions, or absent control responses caused by harness faults
• Maintains factory routing and connector fit for reliable electrical contact

• Disconnect power (unplug appliance or turn off breaker) before inspecting or replacing the harness
• Compare connector shapes and wire colors to ensure correct replacement before installing
• Route harness along original clips and channels; avoid sharp edges, heat sources and pinch points
• Secure connectors firmly; if terminals or connectors are damaged, replace them rather than reusing compromised parts

This harness selector is the wire connector assembly that routes power and signals between the selector switch and oven/range control components, restoring reliable connections and control function. What it does:

• Connects the selector/control switch to burners, igniters, or control modules so selections register properly
• Replaces worn or damaged wires and terminals that can cause intermittent control response
• Helps address symptoms like selector positions not responding, intermittent heating, or controls that fail to change settings
• Maintains factory routing and connector fit for a correct electrical connection

• Disconnect power to the appliance before servicing to avoid shock or damage
• Inspect connectors and wire insulation for damage; match connector shapes and pin counts before installing
• Seat all terminal connectors fully and secure any routing clips or retainers

This wiring harness routes power and signals between a appliance's electrical components, restoring reliable electrical connections so controls, motors, and sensors operate correctly. Designed to replace a damaged or burnt harness. What it does:

• Connects control board, switches, and motors using color-coded wires and molded connectors.
• Restores interrupted circuits that cause no-power or intermittent operation.
• Replaces frayed, burned, or corroded wiring that can create shorts or error codes.
• Helps eliminate loose or broken connector issues that lead to component failures.

• One complete wiring harness with attached connectors as shown.

• Disconnect power before inspecting or replacing the harness to avoid shock or damage.
• Verify connector orientation and wire routing match the original harness; secure with clips/ties as needed.
• Inspect mating connectors and terminal pins for corrosion; replace or clean if needed.

This wiring assembly replaces a worn or damaged wire harness to restore electrical connections between an appliance's controls and components. It helps re-establish reliable power and signal routing for proper appliance operation. What it does:

• Routes power and signal connections between control modules, switches, sensors and major components
• Restores interrupted circuits that can cause controls to be unresponsive or the appliance to fail to start
• Replaces cracked, frayed or heat-damaged wiring that may cause intermittent operation or arcing
• Ensures proper connector fit and factory routing to prevent shorts and electrical faults

• Disconnect power at the breaker or unplug the appliance before starting any work
• Compare the new harness to the old one and follow original wire routing and connector orientation
• Secure harness with existing clips or fasteners; avoid contact with moving parts or hot surfaces

This wire harness routes power and signals between the appliance's control assembly and its components to restore reliable electrical connections and operation. Designed to replace a damaged or worn harness. What it does:

• Connects control board and components so the appliance can receive power and communicate commands
• Replaces frayed, scorched, or broken wiring that can cause intermittent operation or no power
• Helps stop sparking, arcing, or electrical odors when faulty wiring is the source
• Restores secure plug-and-socket connections that may have loosened over time

• One complete wire harness as shown

• Disconnect power (unplug or switch off breaker) before beginning any repair
• Compare new harness to the original to ensure connector types and lengths prior to installation
• Route and secure wiring away from moving parts and heat sources; use existing clips or ties

This UI harness assembly connects the range/oven control board to the front control panel, restoring reliable button and display communication for the user interface. Replaces a damaged or loose harness to regain normal panel operation. What it does:

• Routes signals and power between the control board and touchpads/display so controls respond correctly
• Commonly used when buttons are unresponsive, display is intermittent, or control functions fail
• Helps eliminate loose or corroded connector issues that cause erratic or no UI behavior
• Matches factory connector ends and routing for proper fit and function

• One UI harness assembly as shown

• Disconnect power to the appliance before attempting any repair to avoid electric shock
• Requires removal of the control panel; handle connectors gently to avoid damaging pins
• Verify connectors fully seat and routing follows original path to prevent pinches or interference