Whirlpool Motor

Used U-Tube diagnostic clips to diagnose that most likely problem was a worn Evaporator Fan Motor which is located in the freezer back wall, located in the top third of the unit. I removed 6 hex head screws from the freezer's interior back panel that covers the evaporator coils. The cover is located in the lower 2/3s of the back wall. Removed all shelving. Also removed screws that held in shelf supports on one side of the freezer wall. I then removed the back panel. You may need to... Read more

• Freezer section too warm

The fan has a very thin wire in it's coil, and when that wire breaks, you need a new fan. In a previous repair, i noticed that an ice build-up had dislodged the wiring on my fan and severed the coil winding. I was able to undo the winding a couple of turns and get it working again. But more recently, the fan stopped and there was no repairing it. So i ordered a new fan from AppliancePartsPros.com and it got here in very good time. The new fan was slightly different as the prongs seemed to be... Read more

If the freezer is cold and the fridge is hot, logic would indicate that the fan blowing the cold air from the freezer into the refrigerator is not working. Searched the ApplicancePartsPros.com website for a fan in the freezer compartment and found the video on how to replace one. Followed the steps in the video to get the freezer partially disassembled and found the whole back of the freezer frozen over. Plugged the refrigerator back in and verified that the fan was not working. Unplugged... Read more

Removed the back cover to access the fan area. Clean the area with brush and vac first. Unplugged the Refrigerator. Used a socket set with 1/4" socket. Had an extended and a standard socket. Removed the condensate plastic drain from the bottom of the refrigerator to have more access to the fan. Unplugged the fan motor. Removed the two screws holding the fan in place. Removed the fan unit from the condenser side of the bracket. Place new fan on the fan and installed exactly the way I removed the... Read more

• Noisy
• Freezer section too warm
• Fridge too warm

Replaced motor/fan assembly Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

Checked the evaporator fan it wasn't working properly. Replaced the fan all is good Read more

My KitchenAid refrigerator was not cooling, but the freezer was working perfectly. The help section here listed three parts that could be defective–defrost thermostat, evaporator fan motor and blade, and air diffuser/damper control–so I replaced them all. The videos were EXCELLENT, and despite the difficulty I had squeezing my shoulders into the small freezer compartment, I installed the parts and my refrigerator is cooling perfectly! THANK YOU FOR THE EXCELLENT REPAIR VIDEOS! I am so happy... Read more

• Fridge too warm
• Freezer section too warm
• Noisy

Replaced compressor fan. the video on the website showed step by step. very easy and it fixed the problem. Read more

The repair went well. Never made this type of repair before. Took me around 90 minutes to complete. The worst part was winging it on how to disassemble the bottom drawers. On my Kenmore Elite, it has three freezer compartment sliding trays. The other difficult part for me was removing the clipped in part on the back of the freezer panel. Without knowing what to do it was a little frustrating. after getting to the evaporator unit, removing built-up ice and replacing the unit was fairly easy. The... Read more

Unplugged power cord, shut off hot and cold water valves, and disconnected hot and cold water lines. I taped the lid closed and laid washer down on its front panel to access motor parts underneath. Removed center screw (allen wrench) and then removed large, round, plastic rotor (had to use some force with fingers behind it to get it off). I could see that the gear teeth inside the rotor had been partially stripped off ruining the rotor (and causing the noise). I then removed the clutch... Read more

After checking the suggested fixes and parts on Appliance Parts Pros, I ordered the defrost thermostat and evap motor for my refrigerator, a Kitchen Aid KSSC42QTS00. Installation was very easy, simply emptying the freezer and removing the access panel in the back bottom half. Upon getting everything open, I found out that the existing evap motor was working fine, so I didn't install that part. I did install the defrost thermometer, which was a 5-minute process. I also cleared out the vent... Read more

Ordered the new fan (blower) from AppliancePartsPros. It arrived 3 days later. Pulled the wall oven out of the wall, removed the sheet metal back and removed the noisy fan. Installed the new fan, reinstalled the sheet metal back, shoved it back into it's place, turned the power back on and viola!, much quieter. Read more

Checked and found the evaporator frozen causing the fan to stop working. Took the interior panels off and applied a blow dryer to the ice, once the ice melted I cut the tabs on the grommet holding the fan since everything is thin plastic and replaced the grommet and fan. Placed everything back and found no further issues. Tools I used were a small flat head screwdriver to pry the panels off and a 1/4 socket to remove the center drawer (4), water filter cover (2), and the ice maker (2). Not too... Read more

Went to appliance parts pros and typed in the problem, and they had a video on that problem and how to fix it, easy fix, ordered the part, had it 2 days later, took my washer apart while I was waiting for the part to come, and then reviewed the video several times, and then completed my repair, probably saved 150-200 dollars by doing it myself, also had my dryer conk out last year, did the same thing, looked up the problem, ordered the part, and made the repair, the pair is 20 years old, parts... Read more

We watched the videos posted on AppliancePartsPros.com website several times before starting the work. Once we were confident of the process, we jumped in with the complete disassembly of the washing machine's drum rotating assembly...everything that touched the drum or made it rotate. My son and I disassembled and inspected each part for wear/damage and ordered replacement parts based on condition. The parts came in within 3 days of ordering. My son and I took 3 hours to reassemble and... Read more