Whirlpool Parts

Watche videos on their website - very good! Read more

After watching several YouTube videos on similar problem, I decided to replaced the air diffuser. Read more

• Burning smell
• Will not agitate
• Pumps but will not spin

I pulled the unit away from the wall and noticed black dust on the floor. Unplugged the unit, turned off the water. Removed back panel (about 10 screws with Torx heads) and noticed the belt was off, the drive pulley was loose and wobbling on the shaft, black dust all over the inside. Belt was worn along one side. Some grooves/damage in the outer drum casing around the pulley where it appeared the belt had rubbed. Removed the lower crossbar (2 more screws) to get better access to the drive... Read more

The most difficult part was figuring out how to take the door off as the manual instructions were not clear. Thank you, YouTube for your help. This door doesn't have the more modern release latches. You open the door all the way and stick Allen wrenches into the holes that appear by the joint of the latch. When you close the door to 3/4 or 7/8 closed, the latches are released from the unit and by holding the sides of the door, you pull it out. The whole replacement would take around an hour,... Read more

1. Ordered new gasket. 2. Heated with blow dryer gasket until it resumed its normal shape. 3. Turned off refrig. 4. Cleaned freezer compartment. 5. Removed old gasket. 6. Installed new gasket. 7. Turned on refrig. 8, Operation back to normal in about 6 hours. Read more

Remove and replace Read more

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

Replaced both hot and cold water inlet valves. Works like a charm, issue resolved. Read more

• Spins slowly
• Will not agitate
• Pumps but will not spin

My parents have the older 80 series washer and dryer that gets used way more than a consumer washer and dryer was ever meant to be used. The washing machine finally said im tired. During the spin cycle it was making a really loud squealing noise and during the agitation cycle it would barely agitate the clothes. So i ordered the basket drive to get rid of the squealing during spin cycle and noticed the dogs on the cams were warn and werent grabbing so ordered the whole cam kit to be safe... Read more

Replaced blower belt and nut as per your You tube video. Read more

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

I started with the suspension pad kit and the tub suspension pads. I do have to say if you have an older model washer (mine is approx 17 years old) be prepared to let the inner tub sit in penetrating oil for a few days before attempting to take the tub out. I was able to get to this point on my own and then it wouldn't budge. My husband ended up buying some direct drive tool (it was pretty cool) and was able to break the tub free after two days. Yay! From there he took the the inner tub and put... Read more

I looked on Appliancepartspros.com, it helped me diagnose the problem, told me what parts to buy and showed me a video of how to fix it. Therefore I saved $150 by not having to call a repair shop. Read more

Replaced blower belt and nut as per your You tube video. Read more

I think I could have just replaced the pump, but I chose to replace the whole assembly. The part is more expensive, but all the gaskets, etc, that come with it are new and that made sense to change all at once. I was able to change this in about 30 minutes, without removing the washer from the under-counter space. I did remove the front door panel, but in retrospect that was unnecessary and probably cost me more time than it saved. Empty the washer of parts, remove the front access panel.... Read more

Dishes were 'gritty' with an almost invisible coating of specks smaller than grains of salt. Prior to ordering parts, I had to determine which part(s) needed replaced and which could benefit from a good cleaning. After viewing Appliance Parts Pros YouTube Videos, I removed the Main Manifold (snaps right off) including the Top Spray Arm. I discovered the Flappers of the Docking Station (AP6009888) were worn out and/or missing. I removed the Docking Station simply by popping the old one off... Read more